Cadillacメーカー2000の使用説明書/サービス説明書
ページ先へ移動 of 19
2000 Cadillac D e Ville Outer Wheelhouse Sectioning 1-12 Inner Front Pillar Sectioning 1-9 Inner Center Pillar Sectioning 1-10 Outer Front Pillar Sectioning 1-2 Outer Center Pillar Sectioning 1-4 Rear.
2000 cadillac deville 1-1 Outer Front Pillar , Center Pillar and Quarter Panel Sectioning CAUTION: When performing service on or near the Supplemental Inflatable Restraint (SIR) components or the SIR wiring, the SIR system must be disabled.
Outer Front Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Visually inspect and restore as much of the damage as possible to factory specifications.
Installation Procedure IMPORTANT: Remove all foam prior to welding this section of the service panel. 1. Prepare mating surfaces. 2. Apply weld-through primer to mating surfaces prior to assembly. 3. Weld backing plates to vehicle at rocker. IMPORTANT: Replace hinge pillar blocks prior to welding outer panel.
Outer Center Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Locate an approved sectioning area in the center pillar (Fig.
Installation Procedure 1. Install sleeves on vehicle at rocker and center pillar areas using plug welds. 2. Replace hinge blocks and bolts. 3. Prepare mating surfaces. IMPORTANT: Prior to refinishing, refer to the publication GM4901M-D-2000 “GM Approved Refinish Materials” for recommended products.
1-6 2000 cadillac deville Quarter Panel Sectioning Removal Procedure The service part comes with lower quarter panel extension and taillamp pocket attached. These parts can be left on the vehicle if not damaged. Drill out factory welds on the car and service part and use the outer panel only.
2000 cadillac deville 1-7 Preparation Of Service Part 1. Cut service part in corresponding locations to fit original cut lines. Leave a gap of one-and- one-half times the metal thickness of sectioning joint (Fig. 1-9). 2. Create 100␣ mm (4␣ in) backing plate on rocker panel from unused portion of service part.
1-8 2000 cadillac deville Inner Front Pillar , Center Pillar and Rear Wheelhouse Sectioning Fig.␣ 1-11 — 2000 DeVille Inner Frame Sectioning Locations CAUTION: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled.
2000 cadillac deville 1-9 Inner Front Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Visually inspect and restore as much of the damage as possible to factory specifications.
1-10 2000 cadillac deville Installation Procedure 1. Prepare mating surfaces. IMPORTANT: Prior to refinishing, refer to the publication GM4901M-D-2000 “GM Approved Refinish Materials” for recommended products. Do not combine paint systems. Refer to paint manufacturer’s recommendations.
2000 cadillac deville 1-11 Preparation of Service Part 1. Cut center pillar at laser weld location. This will allow a 25␣ mm (1␣ in) overlap to the vehicle for welding (Fig. 1-16). 2. Notch the weather strip flange to prevent excessive metal thickness in these areas.
1-12 2000 cadillac deville Outer Wheelhouse Sectioning Removal Procedure 1. Locate horizontal laser-weld line in upper quarter area (Fig. 1-18). 2. Measure down 25␣ mm (1␣ in) and scribe a cut line. 3. On the vehicle rocker area, locate and scribe a vertical cut line in the recommended section area.
2000 cadillac deville 1-13 Rear Rail Sectioning The rear rail is available as a complete assembly. It consists of an outer panel, two inner reinforcements, a rail extension, and all necessary component mounting brackets (Fig. 1-20). The outer panel and rear mounting brackets are also available separately to facilitate sectioning.
1-14 2000 cadillac deville Removal Procedure 1. Visually inspect and restore as much of the damage as possible to factory specifications. 2. Remove all related panels and components. 3. Cut the rear rail along the rearward flange of the crossbar (Fig.
2000 cadillac deville 1-15 Installation Procedure 1. Using the original part as a guide, mark a line on the service rail 35␣ mm (1-5/16␣ in) forward of the cut made to the original part; this should be approximately 535␣ mm (21␣ in) without the extension attached to the rail.
1-16 2000 cadillac deville ZERO LINE A B C D E F ALL LENGTHS MEASURED FROM Ø LINE AT TOP HINGE 19 MM HOLE ALL MEASUREMENTS HOLE CENTER TO CENTER 19 MM GAGE HOLE Ø Engine Compartment Dimensions – 2.
2000 cadillac deville 1-17 Ø C A B D E F G 540 469 552 526 925 888 1752 2537 3191 1092 348 358 537 496 504 427 430 496 553 577 D A TUM LINE WIDTH HEIGHT LENGTH Underbody Dimensions – 2000 Cadillac .
1-18 2000 cadillac deville ø A B C D E F D A TUM LINE 829 840 827 836 0 0 1140 1140 2183 849 591 930 964 665 1004 WIDTH HEIGHT LENGTH Body Side Dimensions – 2000 Cadillac DeV ille Description Locat.
デバイスCadillac 2000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Cadillac 2000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCadillac 2000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cadillac 2000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cadillac 2000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cadillac 2000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCadillac 2000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cadillac 2000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCadillac 2000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。