CaliberメーカーRCD110Bの使用説明書/サービス説明書
ページ先へ移動 of 17
CAR CD/MP3 PLA YER / RDS RECEIVER WITH USB INTERF ACE , SD INTERF ACE AU X U S B IN T 2 6 5 RD M 4 RP T 3 OP EN M EN U MO D E ID3 DI S P 1 BA N D PS PT Y AS M UT E 1. P ANEL RELEASE BUT TON 2. ENCODER VOLUME KNOB 3. SYSTEM MENU BUTTON 4. PRESET MEMORY BUTTONS 5.
E - 1 1. HANDLING COMP ACT DISCS MOISTURE CONDENSA TION NOTES ON CDs P . 2 P . 3 P . 4 P . 1 P . 5 P . 6 P . 7 1. 2. 3. 4. 5. NOTES ON DISCS There are paste residue. Ink is sticky (P .5). Stickers that are beginning to peel away , leaving a sticky residue (P .
2. INST ALLA TION 30° DIN FRONT/REAR-MOUNT - DIN FRONT -MOUNT (Method A) Installation the unit 1. Dashboard 2. Half Sleeve 3. Screw 1 7 4 2 3 5 6 1. Dashboard 2.
- DIN REAR-MOUNT (METHOD B) Installation using the screw holes on the sides of the unit. Fastening the unit to the factory radio mounting bracket. 1. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted) and tighten the screws at 2 places on each side.
E - 4 3. DET ACHABLE CONTROL P ANEL(D.C.P) 1. T o attach the front panel back to the unit chassis, firstly join the left guide block hole to the left cylinder ( ), then join the right guide block hole and the right cylinder ( ). T o remove the front panel: 1.
4. WIRING DIAGRAM E - 5 CONNECTOR ISO 1 2 1 2 3 4 7 5 6 8 7 5 3 8 6 4 CONNECTOR B Figure 2 CONNECTOR A ISO CONNECTOR WIRING CHART YELLOW WIRE COLOR VIOLET/BLACK GREY/BLACK GREEN/BLACK WHITE/BLACK VIOL.
Press this button to fold down the front panel. press POWER/MUTE button or any other button on the front of the radio (except Open / Eject) to turn the unit on.
6. AUDIO / MENU OPERA TIONS 3) AUDIO MENU ( MENU ) Press “ MENU ” button to access the Audio Menu. User can navigate thru the Audio Menu intems by pressing the MENU button. Once the desired menu item appears on the display , adjust that option by using the encoder volume knod within 5 seconds.
7. RADIO OPERA TIONS 11) RADIO SIGNAL STRENGTH METER (RSLM) This is use to indicate the signal strength of current radio station broadcast. When you choose RADIO mode, it will show on the display . 4) ST A TION PRESET BUTTONS (M1-M6) 1.Press these buttons briefly to recall the stored stations in the selected band.
8) PTY BUTTON Each time when this button is pressed, the PTY mode will toggle in the following order: PTY Music Group -> PTY Speech Group ->PTY Off Music Group Speech Group M1 POP , ROCK NEW.
M3) REPEA T BUTTON (RPT) Press this button, the current track will be played repeatedly until this button is pressed again. 12) EJECT BUTTON ( ) Press this button to eject the CD from the unit.
10. USB DRIVE OPERA TIONS ST AR T THE USB DEVICE MODE 2. Plug in the USB drive / device completely as indicated in picture 2 (P .2) and display will show “USB PLA Y” to indicate that the USB drive / device is being plugged in correctly & the download has begun.
Open button 11. SD OPERA TIONS 1.Press panel open button to release the front panel.(P .1) 3.The SD card slot is located on the unit as indicated in (P .4). 4. Insert the SD card into the card slot in the correct direction until a “CLICK” sound is heard.
Notes : L OADING DISC NAVIGA TING THROUGH DIRECTORIES AND TRACKS Insert the CD as usual, if it is an MP3 CD , the display will show “MP3 T01” then the message “READING” will appear , when disc scanning completed, the first track on the first directory will play .
(2) SEARCH DIRECTORY / TRACK NAME BY USING ENCODER VOLUME KNOB Under MP3 Play Mode, press AS/PS BUT TON twice, the display shows “ * “. Rotate the ENCODER VOLUME KNOB for selecting the character . In this Encoder Search mode, SELECT button use as move cursor .
E - 16 GENERAL Power Supply Polarity Speaker impedance Power Output Frequency Range Intermediate Frequency Usable Sensitivity Stereo Separation S/N Ratio DC 11 -14V Negative Ground 4 ohms 40W x 4 87.5-108 MHz 10.7 MHz Better than 15dB at S/N 30 dB 25 dB at 1KHz 50 dB 13.
14. TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer .
デバイスCaliber RCD110Bの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Caliber RCD110Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCaliber RCD110Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Caliber RCD110Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Caliber RCD110Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Caliber RCD110Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCaliber RCD110Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Caliber RCD110Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCaliber RCD110Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。