CaliberメーカーRCD264の使用説明書/サービス説明書
ページ先へ移動 of 18
.
Page CONTENTS 01 Contents 02 Installation 04 Using the detachable front panel 05 Wiring iagram 06 Operations 06 07 General perations 0 Radio perations CD/MP3 perations 1 Mixed- CD perations 1 USB pera.
Notes: - Choose the mounting location where the unit will not interfere with the normal driving function of the driver . - Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly .
7. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables. 8. Slide the unit into the sleeve until it locks into place. 9. T o further secure the unit, use the supplied metal strap to secure the back of the unit in place.
If your vehicle is a Nissan, T oyota, follow this mounting instruction. Use the screw holes marked T (T oyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. Fasten the unit to the factory radio mounting brackets.
Wiring diagram L R 15 ISO CONNECT OR ISO connector: Part A: A1: A2: A3: A4: A5: A6: A7: A8: Part B: B1: B2: B3: B4: B5: B6: B7: B8: No Connect No Connect No Connect Battery B+ (Y ellow) Antenna (Blue).
Operations Location and function of controls Front panel: 27 28 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1 1) (12) (13) Power on/off Button ( ), Mute Button V olume Control, Audio/Menu Selector (SEL).
Reset the unit Power on/off 1.T urn off the unit power . 2. () - Rotate the volume control to adjust volume level. - Press the button short and repeatedly to select the volume, bass, treble, balance and fader.
“RETUNE L or RETUNE S” RETUNE L mode: - RETUNE S mode: “MASK DPI or MASK ALL”: - MASK DPI mode: MASK ALL mode: (long/short retune): This function allows you to set the duration after which the automatic search for traffic information or a station with an identical PI should be carried out.
CT -> FREQUENCY -> PTY NONE-> In CDP/USB/SD mode: CT -> FREQUENCY -> PTY NONE -> T rack or file number and Running time The selected information is displayed for 5 seconds, then the radio goes back to the first display mode after 5 seconds.
Short pressing the button, the radio searches for each preset station that saved in the memories of the current band. If the field strength level is more than the threshold level, the radio will hold .
Listening to Traffic Announcement The RDS data are the PI, PS, TP , PTY , T A and AF data. PI PS PTY TP TA AF (Program identification): Code for identifying the radio station. (Program service): Name of the radio station. (Program type): T ype of program such as news, Pop music, sports etc.
Repeat playback Shuffle playback Select the track or file for playback in MP3 or WMA format In CD or MP3/WMA file playback, briefly press the button to Press again to stop repeat playback and resume normal playback.
The unit is equipped with a USB port on the front panel of the unit, you can connect a USB stick through the USB port. When you insert a USB stick through the port, the unit will search the MP3 files and start to play it automatically . If insert a disc into the disc slot while read the file in the USB device, the unit will playing the disc first.
- Do not warp discs. - A disc should always be kept in its case when not in use to prevent from damage. - Do not place discs in the following places: 1. Direct sunlight. 2. Dirty , dusty and damp areas. 3. Near car heaters. 4. On the seats or dashboard.
T rouble shooting Symptom Cause Solution No power The car ignition switch have not turn on. If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse has been blown. Replace a new one.
1. GENERAL 2. CD PLA YER 3. RADIO FM Power Supply Requirements DC 12 V olts, Negative Ground Chassis Dimensions 178(W)x160(D)x 50(H) mm T one Controls -B a s s( a t1 0 0H z ) ± 1 0d B - T reble (at 10 kHz) ±10 dB Maximum Output Power 4x75 watts Current Drain 15 Ampere (max.
W W W . C A L I B E R . N L CALIBER HEAd OffICE • The Netherlands • Fax: +31 (0)416 69 90 01 • E-mail: info@caliber .nl.
デバイスCaliber RCD264の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Caliber RCD264をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCaliber RCD264の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Caliber RCD264の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Caliber RCD264で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Caliber RCD264を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCaliber RCD264の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Caliber RCD264に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCaliber RCD264デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。