Campbell HausfeldメーカーSDM-CD16ACの使用説明書/サービス説明書
ページ先へ移動 of 22
SDM-CD16AC 16 Channel AC/DC Controller Revision: 8/07 Copyright © 1987-2007 Campbell Scientific, Inc..
Warranty and Assistance The SDM-CD16AC 16 CHANNEL AC/DC CONTROLLER is warranted by CAMPBELL SCIENTIFIC, INC. to be free from defects in m aterials and workmanship under norm al use and service for twelve (12) m onths from date of shipment unl ess specified otherwise.
SDM-CD16AC Table of Contents PDF viewers note: These page numbers refer to the printed version of this document. Use the Adobe Acrobat® bookmarks tab for links to specific sections. 1. Function ........................................................
This is a blank page..
SDM-CD16AC 16 Channel AC/DC Controller 0 1 2 3 0 1 2 3 ADDRESSES GND C1 C2 C3 +12V AUTO ON OFF 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 AUTO ON OFF C2 C2 C2 16 C2 C2 C2 16 C2 C2 C2 16 C2 C2 C2 16 C2 C2 .
SDM-CD16AC 16 Channel AC/DC Controller 2. Control Specifications Operating voltage: 12 VDC nominal (9 to 18). Current drain at 12 VDC: 6 m A quiescent; 45 m A per active LED (switch on or auto active).
SDM-CD16AC 16 Channel AC/DC Controller Position of Contacts When Position of Contacts When Coil is Energized (ON) Coil Is Not Energized (OFF) FIGURE 2.
SDM-CD16AC 16 Channel AC/DC Controller TABLE 1. Datalogger to SDM-CD16AC Connections Connection Order SDM-CD16AC Datalogger (see note) Function First 12 V 12 V on datalogger or Power external supply S.
SDM-CD16AC 16 Channel AC/DC Controller Cables connecting the terminals of the datalogger and SDM device should be kept as short as possible to minimize the risk of corr uption of the signals and damage from induced surges.
SDM-CD16AC 16 Channel AC/DC Controller Device Neutral (-) Hot (+ ) NO NC COM FIGURE 4. Typical Wiring Application 4.1.3 Motor Control The CD16AC is a UL approved Start/S top motor controlle r. In the figure below, a typical 5 Am p 115 VAC relay contact ci rcuit shows how to control a three phase motor starter in a Motor Contro l Cen ter (MCC).
SDM-CD16AC 16 Channel AC/DC Controller FIGURE 5. CD16AC Relay Outputs to MCC 5. Address Selection Switches Each SDM-CD16AC can have 1 of 16 addresses. Shipped from the factory, the address is set at 00. The following t able shows switch position and t he corresponding address (see Figure 6).
SDM-CD16AC 16 Channel AC/DC Controller 0 1 2 3 0 1 2 3 BA ADDRESSES FIGURE 6. Addressing 6. Datalogger Programming In CRBasic, the SDMCD16AC instructio n is used to contro l th e SDM- CD16AC. Dataloggers that are pr ogramm ed with CRBasic include our CR800, CR850, CR 1000, CR3000, and CR5000.
SDM-CD16AC 16 Channel AC/DC Controller CDCtrl(1) will be sent to port 1 , th e value held in CDCtrl(2) will b e sen t to port 2, etc. The value held in CDCt rl(32) would be sent to port 16 on the second SDM-CD16AC. Reps: The Reps parameter is the number of SDM-CD16AC devices th at will be controlled with this in struction.
SDM-CD16AC 16 Channel AC/DC Controller The number of SDM-CD16ACs to be addressed is defined by the Reps (repetitions) parameter. Each Rep will sequentially address (00, 01, 02,...32, 33) SDM-CD16ACs starting wi th the address specified in paramet er 2 (Instruction 29 param eter 3).
SDM-CD16AC 16 Channel AC/DC Controller 'Dimension Variables Public src(32) Dim i, count , mask(16) 'Program BeginProg for i=1 to 16 mask(i) = 2^(i-1) next i Scan(20,msec,2,0) count = count + 1 for i=1 to 32 src(i) = count AND mask(((i -1) MOD 16) +1) next i SDMCD16AC(src(),2,1) NextScan EndProg 8.
SDM-CD16AC 16 Channel AC/DC Controller Input Location assignm ents are as follows: Input Location Location Label Description 1..5 Temp #1..#5 Avg temp, greenhouse 1..5 10..14 Heat #1..#5 Heater control, greenhouse 1..5 SDM -CD16AC Port 1..5 15..19 Cool #1.
SDM-CD16AC 16 Channel AC/DC Controller 9: Else (P94) Else, If the hea ter is off, 10: Z=F (P30) 1: 0 F Enter a "0" into hea ter 2: 0 Exponent of 10 control locatio n 3: 10-- Z Loc : 11: End .
SDM-CD16AC 16 Channel AC/DC Controller 21: End (P95) End Then Do/Else/End END COOLER CONTROL LOGIC START FAN CONTROL LOGIC BASED ON HEATER/COOLER 22: If X<=>F (P89) If heater is on 1: 10-- X Loc.
SDM-CD16AC 16 Channel AC/DC Controller 32: If Flag/Port (P91) If flag 2 is set 1: 12 Do if flag 2 is hi gh 2: 30 Then Do Then 33: Beginning of Loop (P87) Start fan loop 1: 0 Delay 2: 5 Loop Count 34: .
SDM-CD16AC 16 Channel AC/DC Controller This is a blank page. 16.
This is a bl ank page..
Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 Nort h Logan, Utah 84 321 UNITED STATES www.campbellsci.com info@campbellsci.com Campbell Scientific Afri ca Pty. Lt d. (CSAf) PO Box 2450 Somerset West 7129 SOUTH AFRICA www.
デバイスCampbell Hausfeld SDM-CD16ACの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Campbell Hausfeld SDM-CD16ACをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCampbell Hausfeld SDM-CD16ACの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Campbell Hausfeld SDM-CD16ACの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Campbell Hausfeld SDM-CD16ACで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Campbell Hausfeld SDM-CD16ACを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCampbell Hausfeld SDM-CD16ACの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Campbell Hausfeld SDM-CD16ACに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCampbell Hausfeld SDM-CD16ACデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。