CanonメーカーTrinitron KV-2199XDKの使用説明書/サービス説明書
ページ先へ移動 of 47
MODEL COMMANDER DEST . CHASSIS NO. KV -2199XDK RM-952 ME SCC-U30J-A MODEL COMMANDER DEST . CHASSIS NO. CHASSIS TRINITRON ® COLOR TV SER VICE MANU AL BG-3S.
– 2 – KV -2199XDK RM-952 SPECIFICA TIONS Note P ower requirements 110-240 V A C, 50/60 Hz P ower consumption (W) Indicated on the rear of the TV T ele vision system B/G, D/K Color system P AL, P AL 60, SECAM, NTSC4.
– 3 – KV -2199XDK RM-952 T ABLE OF CONTENTS Section T itle P age SELF DIA GNOSIS FUNCTION ................................ 4 1. GENERAL ........................................................................ 8 2. DISASSEMBL Y 2-1. Rear Cover Remov al .
– 4 – KV -2199XDK RM-952 The units in this manual contain a self-diagnostic function. If an error occurs, the ST ANDBY/TIMER lamp will automatically begin to flash. The number of times the lamp flashes tr anslates to a probable source of the prob lem.
– 5 – KV -2199XDK RM-952 2. DISPLA Y OF ST ANDBY/TIMER LIGHT FLASH COUNT Diagnostic Item Flash Count* +B overcurrent/overvoltage 2 times V er tical deflection stopped White balance failure 5 times * One flash count is not used for self-diagnostic.
– 6 – KV -2199XDK RM-952 4. SELF-DIA GNOSTIC SCREEN DISPLA Y F or errors with symptoms such as “power sometimes shuts off ” or “screen sometimes goes out” that cannot be confirmed, it is p.
– 7 – KV -2199XDK RM-952 6. SELF-DIA GNOSTIC CIRCUIT [+BovercurrentªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON and the voltage to pin 18 of IC301 should go do wn when V .SYNC is more than sev en v er ticals in a period, the unit will automatically tur n off.
– 8 – KV -2199XDK RM-952 2 WARNING • Dangerously high voltages are pr esent inside the TV . • Operate the TV only between 1 10 – 240 V AC. To prevent fire or shock hazard, do not expose the TV to rain or moisture. Do not operate the TV if any liquid or solid object falls into it.
– 9 – KV -2199XDK RM-952 5 Using Y our New TV Using Y our New TV 1 1 VHF LOW B/G ONE-PUSH AUTOMATIC PROGRAMMING ONE-PUSH AUTOMATIC PROGRAMING 1 2 Notes • If you connect a stereo VCR, connect the yellow plug to (the yellow jack) and the white plug to (the black jack).
– 10 – KV -2199XDK RM-952 8 Using Y our New TV VHF LOW B/G AUTO PROGR TV 1 2 3 4 6 7 8 9 ÷ 0 5 JUMP SOUND MODE FAVORITE PROGR Á ONE-PUSH AUTOMATIC PROGRAMING Presetting channels Y ou can preset up to 100 TV channels in numerical sequence from program number 1 using the remote and the buttons on your TV as well.
– 11 – KV -2199XDK RM-952 9 Using Y our New TV Using Y our New TV 1 Press SELECT until “MANUAL PROGRAM” appears. 2 Press + or –. 3 Press PROGR +/– or the number buttons until the desired program number appears. 4 Press + or – until the desired channel picture appears.
– 12 – KV -2199XDK RM-952 12 Using Y our New TV To T urn off temporarily T urn off completely Mute the sound W atch the video input (VCR, camcorder , etc.
– 13 – KV -2199XDK RM-952 13 Using Y our New TV Using Y our New TV Setting the Wake Up timer 1 Press until the desired period of time appears. 2 Select the TV program or video mode you want to display when you wake up. 3 Press u or set the Sleep timer if you want the TV to turn off automatically .
– 14 – KV -2199XDK RM-952 15 Advanced Operations PICTURE COLOR BRIGHT HUE* TREBLE BASS SHARP SELECT PICTURE 60 Adjusting the picture and sound settings 1 Press SELECT until the desired setting appears. Each time you press SELECT , the setting item will change as follows: 2 Press + or – to adjust the item.
– 15 – KV -2199XDK RM-952 17 Advanced Operations Blocking the channels (CHILD LOCK) Y ou can prevent a child from watching certain programs by using the buttons on the remote control. 1 Select the TV program you want to lock. 2 Press SELECT until “CHILD LOCK” appears on the screen.
– 16 – KV -2199XDK RM-952 19 Additional Information Snowy picture Noisy sound Distorted picture Noisy sound Good picture Noisy sound No picture No sound T roubleshooting If you find any problem while viewing your TV , please check the following guide.
– 17 – KV -2199XDK RM-952 21 Additional Information • Use the fine tuning (FINE) function. (page 10) • Contact your nearest Sony service center . (page 18) –– — Possible cause Symptom Solutions • There is interference fr om external sources, e.
– 18 – KV -2199XDK RM-952 23 Additional Information Remote Control Button function For general TV operations For T eletext operations 1 u (power) button (11) 2 ; (TV) button (12) 3 Number buttons .
– 19 – KV -2199XDK RM-952 SECTION 2 DISASSEMBL Y 2-2. CHASSIS ASSY REMO V AL 1 Chassis assy Lever Lever 2-1. REAR CO VER REMO V AL 1 ten screws (+BVTP 4 × 16) 1 two screw (+BVTP 4 × 16) 2 Rear cover 2-3. F BRACKET REMO V AL 3 One screw (+BVTP 3 × 12) 1 Three connectors 2 F board Lever 2-4.
– 20 – KV -2199XDK RM-952 2-6. TERMINAL BRA CKET REMO V AL A board Terminal board bracket screw (+BVTP 3 x 12) 2-7. DEGA USS COIL REMO V AL 1 Demagnetization coil 2 Tension spring Picture tube 2-5.
– 21 – KV -2199XDK RM-952 2-8. PICTURE TUBE REMO V AL • REMO V AL OF ANODE-CAP NOTE : After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CR T shield or carbon paint on the CRT . • REMOVING PROCEDURES 1 Do not damage the surface of anode-caps with sharp shaped objects.
– 22 – KV -2199XDK RM-952 • The following adjustments should be made when a complete realignment is required or a new picture tube is installed. • These adjustments should be performed with rated power supply voltage unless otherwise noted. Controls and switches should be set as follo ws unless otherwise noted: PICTURE control .
– 23 – KV -2199XDK RM-952 3-2. CONVERGENCE Preparation : • Before starting this adjustment, adjust the focus, horizontal size and vertical size. • Minimize the brightness setting. • Provide dot pattern. (1) Horizontal and V ertical Static Conv ergence (Moving vertically), adjust the V .
– 24 – KV -2199XDK RM-952 4 Y separation axis correction magnet adjustment. 1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN] and [BRIGHTNESS] to [ST ANDARD] . 2. Adjust the Y separation axis correction magnet on the neck assembly so that the horizontal lines at the top and bottom of the screen are straight.
– 25 – KV -2199XDK RM-952 (3) Screen-corner Con vergence ba cd a-d : screen-corner misconvergence a d c b a to d : Permalloy assembly Fix a Permalloy assy corresponding to the misconverged areas 3-3. FOCUS ADJUSTMENT Adjust FOCUS control on the flyback transformer for the best focus.
KV -2199XDK RM-952 KV -2199XDK RM-952 KV -2199XDK RM-952 – 36 – – 37 – – 35 – SECTION 5 DIA GRAM 5-1. BLOCK DIAGRAM YC JUNGLE IC301 CXA2130S <slave:88H> MONITOR OUT TV V in TV L in T.
KV -2199XDK RM-952 – 39 – KV -2199XDK RM-952 KV -2199XDK RM-952 – 38 – – 40 – CN604 CN306 CN703 DY1 DGC B 9V IK 1 5 6 (RGB OUT) 1 E CN704 PICTURE TUBE 1 2 3 4 5 6 H+ H+ H- H- V- V+ 1 2 3 4.
– 41 – KV -2199XDK RM-952 5-4. SCHEMA TIC DIA GRAMS AND PRINTED WIRING BO ARDS Note: • All capacitors are in µ F unless otherwise noted. • All electrolytic capacitors are rated at 50V unless otherwise noted.
– 42 – KV -2199XDK RM-952 4.5Vp-p (V) 3.8Vp-p (V) NTSC 3.58 NTSC 4.43 PA L 0.7Vp-p (H) 1.2Vp-p (H) 1.1Vp-p (H) 920Vp-p 125Vp-p 0.9Vp-p (H) 1.3Vp-p (H) P AL/NTSC 3.58 SECAM/NTSC 4.43 0.8Vp-p (H) SECAM 0.8Vp-p (H) 1.0Vp-p (H) P AL/NTSC 3.58 NTSC 4.43 3.
– 44 – – 45 – – 43 – A 1234 5678 9 1 0 1 1 1 2 13 14 15 16 17 18 19 20 21 22 B C D E F G H I J (1) Schematic Diagram of A 1/2 board 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22.
– 47 – – 46 – – 48 – A 1234 5678 9 1 0 1 1 1 2 13 14 15 16 17 18 19 20 21 22 B C D D E F G H I (2) Schematic Diagram of A 2/2 board HV 1 4 2 3 6 5 11 13 9 8 7 FV SV 10 14 1 2 1 2 3 4 5 1 2.
KV -2199XDK RM-952 KV -2199XDK RM-952 KV -2199XDK RM-952 – 50 – – 51 – – 49 – 5 8 2 6 2 2 3 8 8 8 INT0 INT1 INT2 TEX TX EXTAL XTAL RST MP V DD V SS RMC AN0~AN5 6 PA0~PA7 PORT A PORT B PORT.
– 53 – – 52 – – 54 – A 1234 5678 9 1 0 1 1 1 2 13 14 15 16 17 18 19 20 21 22 B C D D E F G H I (3) Schematic Diagrams of C 3 and VM 1 boards H KG G2 CV KR G1 G4 HV KB 1 1 1 1 1 2 3 4 5 6 5.
KV -2199XDK RM-952 – 57 – KV -2199XDK RM-952 – 58 – A 12345 6 7 B C D D E F G H I (4) Schematic Diagram of F boar d 1 2 1 2 1 2 3 4 1 2 3 4 CN4603 CN4601 CN4602 T4601 F4601 C4602 C4601 C 6 5 4 0 .0 0 4 7 2 5 0 V VDR461 R4601 T4602 1P :TAB 2P :VH 2P :VH T.
KV -2199XDK RM-952 KV -2199XDK RM-952 – 56 – – 55 – PA L 25Vp-p (H) 89Vp-p (H) NTSC 3.58 NTSC 4.43 75Vp-p (H) 4 2 2 2 12 3 SECAM 93Vp-p (H) P AL/SECAM : NTSC : 86Vp-p (H) 95Vp-p (H) 80Vp-p (H).
KV -2199XDK RM-952 KV -2199XDK RM-952 – 60 – – 59 – 5-5. SEMICONDUCTORS DIODE AK04V0 AU-01Z-V1 EL1Z GP08D RD33EB3T RGP02-17EL-6433 D4SB60L ERC04-06SE RN4Z RS3F3 31DQ06-FC5 ERA22-08 ERD29-08J DTZ10B DTZ-TT11-15B RD10S-B MA111-TX UDZS-TE17-5.1B UDZS-TE17-6.
KV -2199XDK RM-952 – 61 – KV -2199XDK RM-952 – 62 – SECTION 6 EXPLODED VIEW NOTE: • Items with no part number and no des- cription are not stocked because they are seldom required for routine service. • The construction parts of an assembled part are indicated with a collation number in the remark column.
– 63 – REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified.
– 64 – REF . NO. P AR T NO. DESCRIPTION REMARK REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified. KV -2199XDK RM-952 C243 1-216-295-91 SHOR T 0 C244 1-164-700-11 CERAMIC CHIP 0.
– 65 – REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified. REF . NO. P AR T NO. DESCRIPTION REMARK KV -2199XDK RM-952 C614 1-126-964-11 ELECT 10MF 20% 50V C616 1-130-202-00 FILM 0.
– 66 – REF . NO. P AR T NO. DESCRIPTION REMARK REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety .
– 67 – REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified.
– 68 – REF . NO. P AR T NO. DESCRIPTION REMARK REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified. KV -2199XDK RM-952 R340 1-216-025-91 RES,CHIP 100 5% 1/10W R345 1-216-081-00 RES,CHIP 22K 5% 1/10W R348 1-208-806-11 RES,CHIP 10K 0.
– 69 – REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified. REF . NO. P AR T NO. DESCRIPTION REMARK KV -2199XDK RM-952 R537 1-208-814-91 RES,CHIP 22K 0.
– 70 – REF . NO. P AR T NO. DESCRIPTION REMARK REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety .
– 71 – REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety . Replace only with part number specified. REF . NO. P AR T NO. DESCRIPTION REMARK KV -2199XDK RM-952 R712 1-215-922-11 MET AL OXIDE 6.
– 72 – REF . NO. P AR T NO. DESCRIPTION REMARK REF . NO. P AR T NO. DESCRIPTION REMARK The components identified by shading and mark ! are critical for saf ety .
デバイスCanon Trinitron KV-2199XDKの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Canon Trinitron KV-2199XDKをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCanon Trinitron KV-2199XDKの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Canon Trinitron KV-2199XDKの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Canon Trinitron KV-2199XDKで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Canon Trinitron KV-2199XDKを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCanon Trinitron KV-2199XDKの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Canon Trinitron KV-2199XDKに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCanon Trinitron KV-2199XDKデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
