CasioメーカーDT-X7の使用説明書/サービス説明書
ページ先へ移動 of 75
Handheld T erminal User’ s Guide Series Be sure to r ead “Safety Precautions” inside this guide before trying to use your Handheld T erminal. E Illustrated operating instructions in this user ’ s guide use laser model of DT -X7 series.
Information in this document is subject to change without advance notice. CASIO Computer Co., Ltd. makes no representations or warranties with respect to the contents or use of this manual and speci fi cally disclaims any express or implied warranties of merchantability or fi tness for any particular purpose.
E-1 Contents Safety Precautions ......................................................................................... E-3 Operating Precautions ................................................................................... E-8 Important .....
E-2 DT -X7 Specifi cations ................................................................................... E-40 Using the USB Cradle (HA-F60IO) ...............................................................E-44 General Guide ....................
E-3 Safety Pr ecautions Congratulations upon your selection of this CASIO product. Be sure to read the following Safety Precautions before trying to use it for the fi rst time.
E-4 W arning Dust and Moisture Though the Handheld T erminal is dust and water splash resistant, its options including the battery pack are not. Keep loose metal objects and containers fi lled with liquid away from your Handheld T erminal and the options.
E-5 Caution Foreign Objects T ake care to ensure that metals or combustible objects are not inserted into the openings of the Handheld T erminal or its options, and not to allow moisture to get inside of them. Location Install the cradle properly on a fl at and stable surface so that it cannot fall down onto fl oor .
E-6 Optional Lithium-ion Battery Pack Danger Never use the Handheld T erminal and its option including the battery pack and battery next to open fl ame, near a stove, or any other area exposed to high heat, or leave them for a long period of time in a vehicle parked in direct sunlight.
E-7 Power Supply / AC Adaptor W arning Do not use the Handheld T erminal at a voltage other than the speci fi ed voltage. Also, do not connect the Handheld T erminal to a multi-plug power strip. Never modify , sharply bend, twist, or pull on the power cord.
E-8 Operating Pr ecautions Y our Handheld T erminal and its options are precision. Improper operation or rough handling can cause problems with data storage and other problems. Note and observe the following precautions to ensure proper operation. Do not continue operating the Handheld T erminal when battery power is low .
E-9 Important This guide does not include any information about programming and download procedures. See the applicable separate documentation for information about the procedures.
E-10 Regulatory Information The USA and Canada GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not applicable to other ar eas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
E-11 L ’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
E-12 Standard lssue date EN 300 328 v1.7.1: 2006.10 EN 50371 (for DT -X7M10R2, DT - X7M30R) 2002 and therefore comply with the essential requirements and provisions of the Directive 1999/5/EC of the E.
E-13 The CASIO DT -X7M10E, DT -X7M10R2, DT -X7M30E, DT -X7M30R and DT -X7M10U models are designed, tested and found to meet the relevant regulatory standards described below .
E-14 Checking in the Box Please check the contents of the box before using the Handheld T erminal for the fi rst time. Open the box and make sure that all the items shown here are included.
E-15 Handheld T erminal System Confi guration Options USB Cradle HA-F60IO Cradle-type Dual Battery Charger HA-F36DCHG DT -X7 Series Ethernet Cradle HA-F62IO Cradle-type Battery Charger HA-F30CHG The illustration shows the USB Cradle (HA-F60IO).
E-16 HA-F20BA T (Battery Pack) HA-F21LBA T (Large-capacity Battery Pack) Dual Battery Charger HA-F32DCHG Battery Pack AC Adaptor for USB Cradle/Ethernet Cradle/ Dual Battery Charger AD-S42120B AD-S421.
E-17 Options AC Adaptor for Cradle-type Dual Battery Charger AD-S60160BE AD-S60160B-N AD-S60160BU Hand Belt HA-F95HB Cable DT -380USB Power Cord for Eur ope AC-CORD-EU Power Cord for North America AC-.
E-18 General Guide 17 Left Front Right Back 1 2 3 4 5 7 6 7 11 10 8 9 12 13 16 15 16 14 23 24 25 24 22 21 21 20 19 18 19 Bottom 17 TOP 17 DT -X7M10E DT -X7M10R2 DT -X7M10U DT -X7M30E DT -X7M30R 1 Indicator 1 Orange: Charging the battery pack. Green: Charging the battery pack is complete.
E-19 7 Cursor Keys Perform the same functions as the up and down arrow keys on a PC keyboard. 8 Enter Key Press when fi nishing entering numerical values or when moving to the next step. 9 Numeric Keys Used to enter numeric values and decimal points.
E-20 21 Strap Holes Used to attach the hand strap. Also used for the hand belt. 22 Reset Switch Used to reset the Handheld T erminal. 23 Hand Belt Holes Used to attach the hand belt. 24 Battery Pack Cover Lock Switch Used to lock the battery cover and to release.
E-21 Loading and Removing the Battery Pack Y our Handheld T erminal uses two types of battery: a battery pack and a memory backup battery . The battery pack is used to power normal operations and to s.
E-22 Loading 1. T urn over the Handheld T erminal. 2. Remove the rechargeable battery pack cover as follows: Slide the left and right lock switches for the rechargeable battery pack cover simultaneously in the direction indicated by the arrows.
E-23 After putting back the cover , fi rmly press the cover so that it is locked in the position by the two Battery Pack Cover Lock Switches. Ensure that both the switches returned all the way down to the home positions as indicated by the two arrows.
E-24 4. Remove the battery pack by pulling up the removal tape as shown in the illustration. Loading the large-capacity battery pack into the Handheld T erminal After loading the large-capacity battery pack, you need to use the special lar ge-capacity battery pack cover in place of the standard battery pack cover .
E-25 Attaching the Hand Strap The hand strap can be used to prevent the Handheld T erminal from dropping when carrying it around. Since there are two strap holes where the hand strap can be attached, use the hole that affords the ease of use. Attach the hand strap according to the procedure described below .
E-26 Setting up Using the Mouse Emulator Function The mouse emulator function lets you make settings and adjustments by using a mouse cursor . T o use the mouse cursor , fi rst set up the mouse emulation mode by following the below procedure. In the emulation mode, the numeric keys and T rigger R key are used to manipulate the mouse cursor .
E-27 Right click (calling up a menu) Move the mouse cursor to the position where you want to click, and press the T rigger R key . Left double click Performing this action while the mouse cursor is on an icon starts an application, opens a fi le, etc.
E-28 Adjusting Display Brightness Y ou can use the following procedure to adjust display brightness to make it easier to read under different lighting conditions. Press the “Fn” key and then press the “5” key or “6” key after con fi rming that “F” is displayed in the lower right corner of the screen.
E-29 Using the Laser Scanner (DT -X7M10E/DT -X7M10R2) 1. After turning on the power , position the laser scanner close to a bar code and then press the trigger key . 2. The laser emits light and scans the bar code. If scanning is completed normally , Indicator 2 displays a green light and a buzzer sounds.
E-30 W ar ning Label This label is a warning and caution label for Class 2 laser products that comply with IEC60825-1:1993+A1:1997+A2:2001. Although Class 2 laser light is only emitted momentarily , never look dir ectly into the beam light.
E-31 Adjusting the Laser Light Emission Width The emission width of the laser light emitted by the Handheld T erminal can be adjusted. Adjust the emission width when it has been changed. The mouse emulator function can also be used to make the adjustment.
E-32 4. Use the “ ”/“ ” keys to move the focus to [Calibration] and press the Enter key . The message appears as shown at right. 5. Press the T rigger Key to emit laser light, and align the light with the barcode for adjusting emission width. Align the laser light with the narrow bars on both sides.
E-33 Using the C-MOS Imager (DT -X7M30E/DT -X7M30R) 1. T urn on the Handheld T erminal, position its C-MOS Imager reader port near the bar code or 2D code, and then press the T rigger Key . 2. The Handheld T erminal reads the code by emitting laser and red lights.
E-34 W ar ning Label DT -X7M30E DT -X7M30R DT -X7M30R-CN This label is a warning and caution label for Class 2 laser products that comply with IEC60825-1:1993+A1:1997+A2:2001. Although Class 2 laser light is only emitted momentarily , never look dir ectly into the beam light.
E-35 Using the Linear Imager (DT -X7M10U) 1. After turning on the power , position the reader port close to a bar code and then press the T rigger key . 2. The LED emits light and scans the bar code. When scanning is completed normally , Indicator 2 displays a green light and a buzzer sounds.
E-36 Performing Communications IR Communication IR communication can be used to transmit data between two Handheld T erminals. When performing IR communication, orient the IR ports of both Handheld T erminals so they are pointing directly at each other .
E-37 Bluetooth ® Communication Bluetooth ® interface can also be used to transmit data between two Handheld T erminals. W ith Bluetooth ® the two Handheld T erminals should be located within about .
E-38 Resetting the Handheld T erminal Resetting the Handheld T erminal is the same as restarting a PC. Performing a reset causes all unsaved inputs and edits to be lost, but data that is already stored in the memory as well as all settings should be unaffected.
E-39 Performing a Full Reset (Initialization) Performing a full reset initializes memory . This means that all data stored in the memory (RAM) is deleted and all the settings are returned to their initial factory settings. Perform a full reset whenever any one of the following conditions exists.
E-40 DT -X7 Specifi cations Model: DT -X7M10E, DT -X7M10R2, DT -X7M10U, DT -X7M30E, DT -X7M30R CPU: Marvell ® PXA270 416MHz Memory: 64MB RAM, 64MB Flash ROM (user area: approx. 28MB) OS: Microsoft ® W indows ® CE5.0 operating system, English V ersion Display: 2.
E-41 WLAN(DT -X7M10R2, DT -X7M30R): Standards: Complies with IEEE 802.1 1b/g Diffusion Modulation: DS: 802.1 1b DS/OFDM: 802.1 1g Frequency: 802.11b/g: 2.
E-42 Dimensional Drawings For Laser Scanner Models Linear Imager Model 52.5mm (2 1 / 16 ") (Displa y) Appro x. Appro x. 51mm (2") (Grip) Appro x. 166mm (6 9 / 16 ") 23.5mm ( 15 / 16 ") (Displa y) 30.5mm (1 3 / 16 ") (Grip) Appro x.
E-43 For C-MOS Imager Models Appro x. 169mm (6 5 / 8 ") 2 3 .5mm ( 15 / 16 ") (Di s pl a y) 3 0.5mm (1 3 / 16 ") (Grip) Appro x. Appro x.
E-44 Using the USB Cradle (HA-F60IO) The optionally available USB Cradle (HA-F60IO) makes it possible to transmit data and fi les between the Handheld T erminal and a PC via a USB connection (download or upload). Y ou can also use the USB Cradle to charge the battery pack installed in the Handheld T erminal.
E-45 1 USB Client Port This port is used to transmit data and fi les (download, upload) by connecting the Cradle to a PC using a USB cable (DT -380USB). A dedicated driver must be installed in the PC before connecting the Cradle to the PC. 2 USB Host Port This port is used to connect a corresponding USB peripheral device.
E-46 Connecting the USB Cradle Power Supply Use the separately sold AC adaptor (AD-S42120B) for the power supply of the USB Cradle. Always make sure to connect the AC adaptor to the USB Cradle before performing communication with the Handheld T erminal.
E-47 4. Connect the USB cable (DT -380USB) to the USB client port on the back of the USB Cradle, and then connect it to the PC. The USB host port is used when connecting the cradle with other USB peripheral device.
E-48 Do not subject the Handheld T erminal and USB Cradle to vibration or impact during communication. This can cause communication to be interrupted. When placing the DT -X7, make sure that it is seated properly and that the power LED at the front of the USB Cradle is lit in gr een.
E-49 Using the Ether net Cradle (HA-F62IO) The optionally available Enthernet Cradle (HA-F62IO) makes it possible to transmit data and fi les between the Handheld T erminal and a PC via a USB or LAN connection (download or upload). Y ou can also use the Ethernet Cradle to charge the battery pack installed in the Handheld T erminal.
E-50 1 USB Client Port This port is used to transmit data and fi les (download, upload) by connecting the Ethernet Cradle to a PC using a USB cable (DT -380USB). The dedicated driver must be installed in the PC before connecting the Ethernet Cradle to the PC.
E-51 Connecting the Ethernet Cradle Power Supply Use the separately sold AC adaptor (AD-S42120B) for the power supply of the Ethernet Cradle. Always make sure to connect the AC adaptor to the Ethernet Cradle before performing communication with the Handheld T erminal.
E-52 4. Before using the cradle ports, remove the caps from the ports. When using a LAN, connect one end of the LAN cable to the LAN port and the other end to the PC or hub. When using a USB connection, connect one end of the USB cable (DT -380USB) to the USB port and the other end to the PC.
E-53 When plac ing the DT-X7, make sure that it is seated pr operly and that the power LED at the fr ont of the Ethernet Cradle is lit in green. Charging and communication will not proceed pr operly if the Handheld T erminal is not mounted properly . Always cap ports that are not being used.
E-54 Using the Cradle-type Battery Charger (HA-F30CHG) The optionally available Cradle-type Battery Charger (HA-F30CHG) lets you char ge the Handheld T erminal’ s battery simply by placing the Handheld T erminal onto the charger . General Guide To p 2 3 Front 4 Left Back 1 1 AC Adaptor Jack Connect the AC adaptor here.
E-55 Connecting the AC Adaptor for Cradle-type Battery Charger Use the separately sold AC adaptor (AD-S15050BE) for the power supply of the Cradle-type Battery Charger . 1. Plug the AC adaptor into the AC adaptor jack on the back of the charger . 2. Next, plug the AC adaptor into a wall outlet.
E-56 Status of Indicator 1 on DT -X7: Orange: Char ging the battery pack. Red: Standby due to battery pack error or the surrounding temperature is out of the charging temperature range. (charging begins when the temperature is within the char ging temperature range) Green: Charging the battery pack is complete.
E-57 Specifi cations 1. Charging Speci fi cations Charging Method: Constant current/voltage Charge Period: Approximately 3 hours (battery pack) Approximately 5.5 hours (large-capacity battery pack) 2. Power Supply Power Source: AC adaptor (AD-S15050BE) Consumption Current: 5V DC 1.
E-58 Using the Cradle-type Dual Battery Charger (HA-F36DCHG) The optionally available Cradle-type Dual Battery Charger (HA-F36DCHG) can be used to simultaneously charge two battery packs. General Guide Left 1 2 4 4 To p Right 2 Bottom 3 Front 1 AC Adaptor Jack This is used to supply power by connecting the AC adaptor (sold separately).
E-59 Bundled Items x Connection bracket (for rear) x Connection scr ews (for rear and side), 2 each x Connection bracket (for side) Used when linking two or more Cradle-type Dual Battery Chargers.
E-60 Charging Battery Pack Use the separately sold AC adaptor (AD-S60160BE/AD-S60160BU) for the power supply of the Cradle-type Dual Battery Charger . 1. Plug the cord from the AC adaptor into the AC adaptor jack of the Cradle-type Dual Battery Charger .
E-61 Connecting Multiple Cradle-type Dual Battery Chargers Y ou can connect up to three Cradle-type Dual Battery Chargers. Doing so makes it possible to supply power to all the Cradle-type Dual Battery Chargers using one dedicated AC adaptor .
E-62 Specifi cations 1. Charging Speci fi cation Charging Method: Constant current/voltage Charge Period: Approx. 3 hours (1 standard battery pack) Approx. 5.5 hours (1 large-capacity battery pack) 2. Power Supply Power Source: AC adaptor (AD-S60160BE/AD-S60160BU) Consumption Current: 1.
E-63 Important ! Never short out the power contacts of the Cradle-type Dual Battery Charger . This can damage the Cradle-type Dual Battery Charger . Allowing the power contacts become wet can cause an electric shock or fi re. In addition, if the contacts become soiled, contact may be impaired r esulting in poor charging.
E-64 Using the Dual Battery Charger (HA-F32DCHG) The optionally available Dual Battery Charger (HA-F32DCHG) can be used to simultaneously charge two battery packs.
E-65 1 Charge Indicator LED This LED indicates the charge status of the battery pack(s). Off: Not char ging the battery pack. Red: Charging the battery pack. Red Flashing: Battery pack problem Green Flashing: Standby Green: Charging the battery pack is complete.
E-66 Charging Battery Pack Use the separately sold AC adaptor (AD-S42120B) for the power supply of the Dual Battery Charger . 1. Plug the cord from the AC adaptor into the AC adaptor jack of the Dual Battery Charger . 2. Plug the AC cord into a wall outlet.
E-67 Connecting Multiple Dual Battery Chargers Y ou can connect up to three Dual Battery Chargers. Doing so makes it possible to supply power to all the Dual Battery Chargers using one dedicated AC adaptor . 1. As shown in the illustrations below , remove the connector covers of the Dual Battery Chargers you want to connect to each other .
E-68 Specifi cations 1. Charging Speci fi cation Charging Method: Constant current/voltage Charge Period: Approx. 3 hours (1 standard battery pack, normal temperature) Approx. 5.5 hours (1 large-capacity battery pack, normal temperature) When charging two battery packs: Approx.
E-69 Using Rechargeable Battery Pack HA-F20BA T HA-F21LBA T Y our Handheld T erminal supports use of two battery pack types, one at a time, of different capacity . Y ou can select the one that best suits your needs in terms of operating time, the type of options you need to use, etc.
E-70 Battery Pack Specifi cations Model: HA-F20BA T Rated Capacity: 4.07WH (1 100mAh) Rated V oltage: 3.7V Dimensions: Approximately 36(W) × 55(D) × 9(H) mm (1 7 ⁄ 16 "W × 2 3 ⁄ 16 ".
E-71 Attaching the Hand Belt (HA-F95HB) T o use the Hand Belt (HA-F95HB), attach it to the DT -X7 as follows. Items Included • Screw (2pcs) • Hand Belt • Holdfast Attaching the Hand Belt Attach the Hand Belt as described below . 1. T urn the DT -X7 over .
E-72 3. Thread the looped cord on the end of the Hand Belt through one of the strap holes at the bottom of the DT -X7. (Y ou can use either hole.) Strap holes 4. Feed the belt through the wire loop on the mount, fold it back and secure it with the hook-loop fastener .
CASIO COMPUTER CO., L TD. 6-2, Hon-machi 1-chome Shibuya-ku, T okyo 151-8543, Japan.
デバイスCasio DT-X7の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Casio DT-X7をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCasio DT-X7の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Casio DT-X7の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Casio DT-X7で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Casio DT-X7を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCasio DT-X7の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Casio DT-X7に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCasio DT-X7デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。