CDAメーカーHG3602の使用説明書/サービス説明書
ページ先へ移動 of 24
Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.
2 Important This appliance is designed and manufactur ed solely for the cooking of domestic (household) f ood and is not suitable for an y non domestic application and ther ef ore should not be used in a commercial envir onment. The applianc e guar antee will be void if the appliance is used within a non domestic envir onment i.
3 Important Saf eguar ds and R ecommendations – Do not carry out any cleaning or maintenance without first disconnecting the appliance from the electrical supply. – During and after use of the hob, certain parts will bec ome very hot. Do not touc h hot parts.
4 Featur es and T ec hnical Data Cooking P oints 1 . T riple ring burner (TR) - 3,50 kW 2. Rapid burner (R) - 3,00 kW 3. Semi-rapid burner (SR) - 1 ,75 kW Contr ol Panel 4. T riple ring burner (1) control knob 5. Rapid burner (2) contr ol knob 6. Semi-rapid burner (3) contr ol knob Not e: – The electric ignition is incorporat ed in the knobs.
5 How t o Use the Hob Gas Burners Gas flow to the burners is adjust ed by turning the knobs (illustrated in fig.2) whic h contr ol the valves. T urning the knob so that the indicator line points to .
6 Lighting Gas Burners In order t o light the burner , you must: 1 – Press in the corr esponding knob and turn count er -clockwise (fig. 3) t o the full flame position marked by the symbol and hold the knob in until the flame has been lit. In the case of a mains failure light the burner with a mat ch or lighted t aper .
7 Choice o f Burner The symbols printed on the panel by the side of the knob indicate whic h burner you ar e contr olling. Choose a suitable burner depending on the cookwar e diameter and capacity. The pan diameter should be suitable for the burner power to make the most of the burner's high efficiency and not waste fuel.
8 Corr ect use of T riple-Ring Burner The flat-bottomed pans ar e to be placed dir ectly onto the pan-support. T o use the WOK you need to place the pr oper stand in order to av oid any faulty operation of the triple-ring burner (Figs. 5a - 5b). Model: WRONG CORRE CT Fig.
9 Fig. 6 Fig. 7.
10 Cleaning and Maintenanc e Gener al Tips – Befor e cleaning the hob switc h it off and wait f or it to cool down. – Clean with a cloth, hot water and soap or liquid deter gent. – Do not use products whic h ar e abrasive, c orrosive or c hlorine based.
11 Burners and Grids – These parts can be remov ed and cleaned with appropriat e products. – After cleaning, the burners and their flame spr eaders must be well dried and corr ectly r eplaced. – It is v ery important to c heck that the burner flame spreader and the cap have been corr ectly positioned.
12 Corr ect Position o f T riple Ring Burner The triple ring burner must be corr ectly positioned (see fig. 9); the burner ribs must be fitted in their housing as shown by the arr ow . The burner corr ectly positioned must not rot ate (fig. 1 0). Then position the cap A and the ring B (figs.
13 Corr ect Positioning o f the Semi-r apid and Rapid Burners – It is very important to check that the burner flame spreader F and the cap C have been correctly positioned (see figs. 1 3 and 1 4). They shall be level and must not rot ate. Failur e to do so can cause serious pr oblems.
14 TIPS FOR INS T ALLA TION Location – The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a r oom or space containing a bath or a show er . – The appliance must not be installed in a bed-sit r oom of less than 20m 3 .
15 30 mm Space for connections Clearance Separator Installation T echnical Information f or the Installer In or der to install the hob into the kitc hen fixture, a hole with the dimensions shown in fig.
16 3 cm min 3 cm 4 cm S A R Fast ening the Cookt op Each cooktop is provided with an installation kit including brackets and screws for fastening the cooktop to benc hes fr om 30 to 40 mm thick.The kit includes f our R brac kets and f our self-thr eading scr ews S (figs.
17 Gas Supply Requir ements Important Not e This appliance is supplied for use on NA TURAL GAS or LPG (check the gas r egulation label attac hed on the appliance). – Appliances supplied for use on NA TURAL GAS: they are adjusted for this gas only and cannot be used on any other gas (LPG) without modification.
18 Gas Connection The installation of the gas appliance to Natural Gas or LP Gas must be carried out by a suitably qualified and register ed installer .
19 Gas connection Cat: II 2H3+ The fitting (fig. 2 1) is made up of: – 1 nut A – 1 elbow fitting C – gasket F Connection t o the Gas Supply – Be careful when flexible pipes ar e used that they do not come into contact with moving parts.
20 J J Con v er sion to Natur al Gas or LPG Replacing the Burner Inject ors If the NA TURAL GAS/LPG conversion kit is not supplied with the appliance this kit can be pur chased by contacting the A fter -Sales Service. Choose the injectors t o be replac ed accor ding to the table below .
21 Regulating the Burner Minimum Set ting When changing from one type of gas to another , the minimum tap output must also be corr ect, considering that in this position the flame must be about 4 mm long and must remain lit even when the knob is turned sharply from the maximum t o the minimum position.
22 Mains Electricity Connection Incorr ect installation ma y be danger ous and the manufacturer can no t be held responsible. W arning! This appliance must be earthed The manufacturer declines all responsibility f or any problem caused b y failur e to observ e this rule.
23 Appliance Servicing CDA pr ovide a quality and effective after -sales service to cover all y our servicing needs. Please attac h your r eceipt to this page f or safekeeping. Please help us to help you by ha ving the following inf ormation available when booking a servic e-call: 1 .
Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu T o contact our Customer Car e Department, or for Servic e, please contact us on the det ails below .
デバイスCDA HG3602の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
CDA HG3602をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCDA HG3602の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。CDA HG3602の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。CDA HG3602で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
CDA HG3602を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCDA HG3602の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、CDA HG3602に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCDA HG3602デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。