Char-Broilメーカー5101194の使用説明書/サービス説明書
ページ先へ移動 of 20
04201101 WARNING Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
2 Installation Safety Precautions • • National Fuel Gas Code, NFPA 54 / ANSI Z223.1 NFPA/ANSI 58. National Electrical Code, ANSI / NFPA 70. Use appliance only with LP (propane) gas and the regulator/valve assembly supplied. Appliance installation must conform with local codes, or in their absence with .
3 T o insure your satisfaction and for follow-up service, register your product online at: www .g rillr e gistr a tion.com Table of Contents Use and Care .................................... 2-10 Safety Symbols ...............................2 Cylinder Cylinder Cylinder Cylinder Cylinder Installation Safety Precautions .
D ANGER • NEVER store a spare LP cylinder under or near the appliance or in an enclosed area. • Never fill a cylinder beyond 80% full. • An over filled or improperly stored cylinder is a hazard due to possible gas release from the safety relief valve.
• A frosty regulator indicates gas overfill. Immediately close LP cylinder valve and call local LP gas dealer for assistance. • Do not release liquid propane (LP) gas into the atmosphere. This is a hazardous practice. • T o remove gas from LP , contact an LP dealer or call a local fire department for assistance.
Hold coupling nut and regulator as shown for proper connection to LP cylinder valve. C Straight 6. An additional one-half to three quarters turn is required to complete connection. Tighten by hand only - do not use tools. NOTE: do not use this Regulator! T urn the coupling nut clockwise to tighten to a full solid stop.
WARNING Ignitor Lighting 1. Open lid during lighting. 2. Press and turn the control knob to the position. 3. T urn knob rapidly . 4. If ignition does not occur in 5 seconds, turn the burner control knob , wait 5 minutes, and repeat lighting procedure.
SOLUTION: Wait for appliance to cool. Clean burner often. Spiders and insects don’t care if your appliance is brand new or you just cleaned it. Use a hose with a nozzle attached. Forced water will wash out the web. Natural Hazard • Spiders CA UTION FACT: Sometimes spiders and other small insects climb into the burner tube.
Job Routine Cleaning Fingerprints and Smears Stubborn Stains and Discoloration Grease and Blood Burnt-on or Baked-on Foods Grease and Oil Cleaning Agents* W arm W ater , Soap, Ammonia, Detergent 3M St.
Problem Burner will not light using ignitor . Burner will not match- light. Sudden drop in gas flow or low flame. Flames blow out. Flashback... (fire in burner tube). Unable to fill LP cylinder Possible Cause — Electrode and burner are wet. — Electrode is cracked or broken, “sparks at crack”.
ST OP! Missing a part? No need to go back to the store! The store where you made your purchase does not stock parts for this item. If you need parts, whether they are missing or damaged, call the Customer Service toll free Help Line. Call us and we will gladly ship the part you need FREE OF CHAR GE.
Parts Diagram A B C C D E F F G H I J K L L M M F N O 12.
Assembly Step 1 Slide tool hooks onto one of the towel bars prior to assembly . Attach each towel bar using two . 1/4-20x3/4” machine screws DO NOT LIFT UNIT USING TOWEL BARS. 1/4-20x3/4” Machine Screw Qty: 4 Wrap/Body 55700670 Towel bar 55700667 Tool hook 1/4-20x3/4” Machine Screw Step 2 Feed burner tube through center hole of heat shield.
Step 3 Position rotary ignitor as shown below . Attach ignitor behind control panel using two . #8x1/2” self-tap screws #8x1/2” Self-Tap Screw Qty: 2 Rotary ignitor 55700666 #8x1/2” Self-Tap Scr.
Step 5 Align valve with burner tube. Figure A #10- 24x3/8” machine screws #10-24 hex/keps nuts #10x1/2” self-tap screw See for proper valve-to-burner engagement. Secure control panel to body at each end using two and two . Inside body , insert one through body into panel.
Step 8 Step 7 Lift body assembly and place onto base. Back/open-end of body assembly should face back of base. Back of base has locking casters, front has non-locking casters.
Cylinder valve must face to rear of cart once cylinder is attached. Failure to install cylinder correctly may allow gas hose to be damaged in operation, resulting in the risk of fire. CA UTION Step 9 Place cover assembly onto top. Align lower hinge holes with holes on back side of top.
18.
Please register your product online at: (If you register online, you do not need to send in this registration card.) WWW .GRILLREGISTRA TION.COM 19.
Char-Broil, LLC • Columbus, GA 31902 • Assembly Instructions © 2005.
デバイスChar-Broil 5101194の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Char-Broil 5101194をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChar-Broil 5101194の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Char-Broil 5101194の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Char-Broil 5101194で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Char-Broil 5101194を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChar-Broil 5101194の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Char-Broil 5101194に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChar-Broil 5101194デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。