Chicago Electricメーカー91511の使用説明書/サービス説明書
ページ先へ移動 of 18
7” POR T ABLE WET TILE SA W Model 91511 ASSEMBL Y AND OPERA TING INSTR UCTIONS Distributed Exclusiv ely by Harbor F reight T ools 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com Cop yr ight © 2004 b y Harbor F reight T ools ® .
PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual f or the safety w ar nings and precautions , assembly , operating, inspection, maintenance and cleaning procedures, par ts list and assemb ly diagram. K eep your in voice with this manual.
3. Keep b ystanders, children, and visitor s awa y while operating a power tool. Distractions can cause y ou to lose control. Protect others in the work area from debris such as chips and spar ks. Provide barriers or shields as needed. PERSONAL SAFETY 1.
2. Do not use the power tool if the P ower Switc h does not turn it on or off. Any tool that cannot be controlled with the P ower Switch is dangerous and must be replaced. 3. Disconnect the P ower Cord Plug fr om the power sour ce before making an y adjustments, changing accessories, or storing the tool.
2. Double insulated tools are equipped with a polarized plug (one prong is wider than the other). This plug will fit in a polarized outlet only one wa y . If the plug does not fit fully in the outlet, rever se the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet.
resistance path to carr y electricity aw ay from the user , reducing the risk of electr ic shock. (See Figure A.) 2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool.
5. If you are using one e xtension cord f or more than one tool, add the nameplate amperes and use the sum to deter mine the required minimum cord siz e. (See Figure B.) 6. If you are using an e xtension cord outdoors, mak e sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptab le for outdoor use .
SPECIFIC SAFETY R ULES 1. Maintain labels and nameplates on the W et Tile Saw . These carr y impor tant inf or mation. If unreadable or missing, contact Harbor F reight T ools for a replacement. 2. D ANGER! Keep hands and fingers awa y from cutting area and Sa w Blade.
13. Bef ore using the W et Tile Saw , make sure the Saw Blade is pr operly mounted on the Saw Spindle. Make sure the Sa w Blade is balanced, and is not crac ked or bent. 14. The Saw Blade will become hot while cutting. Allo w the Saw Blade to completely cool bef ore touching.
SKU 91511 P A GE 10 25. W ARNING! People with pacemaker s should consult their ph ysician(s) before using this pr oduct. Electromagnetic fields in close proximity to a hear t pacemaker could cause interf erence to or f ailure of the pacemaker .
SKU 91511 P A GE 11 Saw Blade (6) from the Spindle of the Wet Tile Saw . Then, install a new diamond Saw Blade with a 7” diameter , 5/8” round arbor hole, and rated at a minimum 3,600 RPM.
SKU 91511 P A GE 12 3. Check to mak e sure the Blade Guard (2) mov es freely upward and do wnward. (See Figure D .) 4. Close the Left Side Cutting T able (26). (See Figure D .) T o Attach The Fence And Miter Guide: 1. Place the F ence (11) on top of the Right Cutting T ab le (10) and clamp both ends of the F ence to secure it in place.
SKU 91511 P A GE 13 3. Make sure the P ower Switch (21) is in its “OFF” position. Then, plug the P ower Cord (17) into the nearest 120 v olt, grounded, electrical outlet. (See Figure G.) T o P erform Straight Cutting: 1. Lift the front and rear Le v ers of the F ence (11).
SKU 91511 P A GE 14 FIGURE G WORKPIECE (NO T INCLUDED) FENCE (11) FENCE SCALE FENCE LEVER FENCE LEVER PO WER SWITCH (21) 2. Raise the Right Cutting T able (10) to the desired angle of cut (i.e ., 15°, 30°, 45°, or 60° ). (See Figure next page .) 3.
SKU 91511 P A GE 15 FIGURE H RIGHT CUTTING T ABLE (10) WORKPIECE (NO T INCLUDED) PO WER SWITCH (21) ST AND (0° to 60°) and tighten the Lock Knob to loc k the Miter Guide in place. (See Figure I.) 3. Place the workpiece flush against the Miter Guide (24).
INSPECTION, MAINTENANCE, AND CLEANING 1. W ARNING! Alwa ys make sure the P ower Switc h (21) is in its “OFF” position, and unplug the P ower Cord (17) fr om its 120 volt electrical outlet before perf orming any inspection, adjustments, maintenance, or c leaning.
P AR TS LIST SKU 91511 P A GE 17 P AR TS LIST SKU 91511 P A GE 17 Part # Description Qt y . Part # Description Qty. 1 Screw 1 18 Motor Bottom Base 1 2 Blade Guard 1 19 Electrical Cord Fixed Head 1 3 W.
SKU 91511 P A GE 18 LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every ef fort to assure that its products meet high quality and durability standards, and warrants to the origina.
デバイスChicago Electric 91511の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Chicago Electric 91511をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChicago Electric 91511の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chicago Electric 91511の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chicago Electric 91511で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chicago Electric 91511を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChicago Electric 91511の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chicago Electric 91511に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChicago Electric 91511デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
