Chicago Electricメーカー99702の使用説明書/サービス説明書
ページ先へ移動 of 22
AIRLESS P AINT SPRA Y MACHINE 99702 SET UP AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: http://www .harborfreight.com Read this material before using this product.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 2 SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 3 plugs with grounded power tools. Unmodied plugs and matching out - lets will reduce risk of electric shock. Do not expose power tools to rain b. or wet conditions. Water entering a power tool will increase the risk of electric shock.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 4 ries, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool ac - cidentally .
SKU 99702 For technical questions, please call 1-800-444-3353. Page 5 grounded. Ground Fault Circuit Inter- rupter (GFCI) should also be imple- mented – it prevents sustained elec- trical shock.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 6 Use tools with the lowest vibration 4. when there is a choice between dif- ferent processes. Include vibration-free periods each 5. day of work. Grip tool as lightly as possible (while 6.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 7 Double Insulated T ools: T ools with T wo Prong Plugs T ools marked “Double Insulated” do 1.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 8 RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOL T) NAMEPLA TE AMPERES (at full load) EXTENSION CORD LENGTH 25’ 50’ 75’ 100’ 150’ 0 – 2.0 18 18 18 18 16 2.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 9 SPECIFICA TIONS Electrical Requirements 120 V~ / 60 Hz / 7.5 A Motor 3/4 HP Operating PSI 2350 – 2650 psi Paint Flow 0.33 GPM Fuse Class F , F10A/250 V Hose Size 1/4” Oil Requirement Hydraulic Oil UNP ACKING When unpacking, make sure that the item is intact and undamaged.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 10 Remove plastic cap and thread the 4. pressure hose onto the hose spray port and secure. Hose connected to spray port Power Switch 5. Remove the plastic cap on the end of the spray gun and thread the other end of the hose onto it.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 1 1 W ork Piece and W ork Area Set Up Designate a work area that is clean 1. and well-lit. The work area must not allow access by children or pets to prevent injury and distraction. Route the power cord along a safe 2.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 12 Allow the unit to draw paint until all air 10. and impurities are cleansed from the system and the paint runs pure. T urn the power Switch to its “OFF” 1 1. position and secure the return tube in its normal operating position.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 13 Adjust the pressure control dial until 23. a solid coat of paint of desired thick- ness is achieved. Painting T ips: 24. Spray 10 to 12 inches from the surface. Begin moving the Gun before squeezing the T rigger .
SKU 99702 For technical questions, please call 1-800-444-3353. Page 14 MAINTENANCE AND SER VICING Procedures not specically explained in this manual must be performed only by a qualied technician.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 15 T urn the power switch Off and un- o.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 16 T roubleshooting Problem Possible Causes Likely Solutions Sprayer will not start No power at outlet. 1. Cord not connected. 2. Sprayer turned off under 3. pressure. Check power at outlet.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 17 PUMP P ARTS LIST Part Description Qty 1 Housing 1 2 Rocker 1 3 Inlet V alve Assembly 1 4 Retaining Ring 1 5 Pin 1 6 W asher 1 7 Screw 1 8 Nut 1 8.1 Bush 1 9 W asher 1 10 T op Seal 1 10.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 18 PUMP DIAGRAM.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 19 PUMP DIAGRAM, CONTINUED.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 20 SUCTION TUBE ASSEMBL Y P ARTS LIST & DIAGRAM Part Description Qty 1B Hose Nut 1 2B Circlip 1 3B Connection 1 4B T ube 1 5B .
SKU 99702 For technical questions, please call 1-800-444-3353. Page 21 GUN P ARTS LIST & DIAGRAM Part Description Qty 1C Housing 2 2C Elbow 1 3C Pin 1 4C Seal 1 5C W asher 1 6C W asher 1 7C Ball 1.
SKU 99702 For technical questions, please call 1-800-444-3353. Page 22 Record Product’ s Serial Number Here: Note: If product has no serial number , record month and year of purchase instead.
デバイスChicago Electric 99702の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Chicago Electric 99702をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChicago Electric 99702の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chicago Electric 99702の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chicago Electric 99702で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chicago Electric 99702を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChicago Electric 99702の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chicago Electric 99702に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChicago Electric 99702デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。