Chicago ElectricメーカーModel 90891の使用説明書/サービス説明書
ページ先へ移動 of 25
10” COMPOUND SLIDE MITER SA W Model 90891 SET UP AND OPERA TING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® .
Page 2 SKU 90891 For technical questions, please call 1-800-444-3353. REV 05i, 07h SPECIFICA TIONS Electrical Requirements 120 V / 60 Hz / 4600 RPM 10.8 A Input Working Amperage (with load) 1-3/4 HP Motor / Single Phase 2-Prong Power Plug Double Insulated Motor w/ External Access Brushes Arbor Diameter 5/8” (0.
Page 3 SKU 90891 For technical questions, please call 1-800-444-3353. Do not operate power tools in explosive atmospheres, such as in the pres- ence of ammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. Keep bystanders, children, and visitors away while operating a power tool.
Page 4 SKU 90891 For technical questions, please call 1-800-444-3353. Dress properly . Do not wear loose clothing or jewelry . Contain long hair . Keep your hair , clothing, and gloves away from moving parts. Loose clothes, jewelry , or long hair can be caught in moving parts.
Page 5 SKU 90891 For technical questions, please call 1-800-444-3353. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SER VICE T ool service must be performed only by qualied repair personnel.
Page 6 SKU 90891 For technical questions, please call 1-800-444-3353. When replacing the Saw Blade, make sure the new Saw Blade has a diam- eter of 10”, has an RPM rating of at least 4600, and has an arbor hole of 5/8” diameter . T o avoid accidental injury , always wear heavy duty work gloves when changing a Saw Blade.
Page 7 SKU 90891 For technical questions, please call 1-800-444-3353. job better and more safely at the rate for which it was intended. Do not modify this product, and do not use this product for a purpose for which it was not in- tended.
Page 8 SKU 90891 For technical questions, please call 1-800-444-3353. Grounded T ools: T ools with Three Prong Plugs T ools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet.
Page 9 SKU 90891 For technical questions, please call 1-800-444-3353. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
Page 10 SKU 90891 For technical questions, please call 1-800-444-3353. UNP ACKING When unpacking, check to make sure all the parts shown on the Parts Lists on pages 22 and 23 are included. If any parts are missing or broken, please call Harbor Freight T ools at the number shown on the cover of this manual as soon as possible.
Page 1 1 SKU 90891 For technical questions, please call 1-800-444-3353. BAFFLE PLA TE (151) HOLDER (149) WING SCREW (148) ADJUSTING KNOB (102) GUIDE FENCE (105) WING SCREW (97) FIGURE E A workpiece Clamp Assembly (95, 96, 97, 98, 99, 100, 101, 102) can be installed by inserting the Assembly into the hole located in the Guide Fence (105).
Page 12 SKU 90891 For technical questions, please call 1-800-444-3353. 1/4” MOUNTING HOLE 1/4” MOUNTING HOLE FIGURE F FRONT COVER WITH SUPPORT LEG (1 17) Use two C-clamps (not included) to secure the back side of the Miter Saw to the table/workbench.
Page 13 SKU 90891 For technical questions, please call 1-800-444-3353. FLA T HEAD SCREW (60) CENTER COVER (55) FIGURE H SAFETY COVER (58) Remove the Flat Head Screw (60) and Center Cover (55).
Page 14 SKU 90891 For technical questions, please call 1-800-444-3353. HEX SOCKET WRENCH (150) HEX FLANGE HEAD BOL T (61) FLANGE (52) HEX FLANGE HEAD BOL T (61) FLANGE (52) FIGURE J BLADE CASE (43) ARROW SA W BLADE (51) ARROW FIGURE K Remove the old Saw Blade (51).
Page 15 SKU 90891 For technical questions, please call 1-800-444-3353. SA W BLADE (51) HEX FLANGE HEAD BOL T (61) FLANGE (52) SPINDLE (35) INNER FLANGE (65) FIGURE L Insert the Flange (52) onto the Spindle (35) and against the Saw Blade (51). NOTE: Make sure the larger diameter side of the Flange is against the Saw Blade.
Page 16 SKU 90891 For technical questions, please call 1-800-444-3353. The Power Switch: Note: The Miter Saw can be disabled for safety purposes by removing the Safety But- ton (16). Make sure to store the Safety Button in a safe place, and do not lose it.
Page 17 SKU 90891 For technical questions, please call 1-800-444-3353. KERF BOARD (1 14) HEX HEAD BOL T (71) SA W BLADE (51) MOTOR HOUSING (26) TURN BASE (125) FIGURE M Push the Miter Saw’s Motor Housing (26) forward as far as it will go. Notice whether the edge of the Saw Blade (51) passes completely through the Kerf Board (1 14).
Page 18 SKU 90891 For technical questions, please call 1-800-444-3353. T o Adjust The Miter Angle: W ARNING! Prior to performing this procedure, make sure the Power Cord of the Miter Saw is unplugged from its electrical outlet.
Page 19 SKU 90891 For technical questions, please call 1-800-444-3353. T o Adjust The Support Screw: The Support Screw (138) can be adjusted by turning it clockwise to lengthen it or by turning it counter- clockwise to shorten it. It should be adjusted so that it rests just above the surface of the table or bench the saw is mounted on.
Page 20 SKU 90891 For technical questions, please call 1-800-444-3353. OPERA TION Make sure the Power Cord of the Miter Saw is unplugged from its electri- cal outlet. Then, if necessary , make adjustments to the workpiece Holder (149), Bafe Plate (151), cutting depth, and miter angle and/or bevel angle.
Page 21 SKU 90891 For technical questions, please call 1-800-444-3353. INSPECTION, MAINTENANCE, AND CLEANING W ARNING! Always make sure the Switch Lever (25) is in its “OFF” position, and unplug the Power Cord from its 120 volt electrical outlet before performing any inspection, adjustments, maintenance, or cleaning.
Page 22 SKU 90891 For technical questions, please call 1-800-444-3353. REV 05b P ARTS LIST T orsion Spring Assy . * * Includes: #57 Spindle Sleeve and #58 Safety Cover . (Note: Customer must save old brass sleeve from old Safety Cover and use it when installing new #56 T orsion Spring Assembly).
Page 23 SKU 90891 For technical questions, please call 1-800-444-3353. P ARTS LIST - CONTINUED REV 04d.
Page 24 SKU 90891 For technical questions, please call 1-800-444-3353. Note: Some parts are listed and shown for illustration purposes only , and are not avail- able individually as replacement parts.
Page 25 SKU 90891 For technical questions, please call 1-800-444-3353. ASSEMBL Y DIAGRAM - CONTINUED REV 04d 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 1 1.
デバイスChicago Electric Model 90891の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Chicago Electric Model 90891をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはChicago Electric Model 90891の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Chicago Electric Model 90891の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Chicago Electric Model 90891で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Chicago Electric Model 90891を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はChicago Electric Model 90891の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Chicago Electric Model 90891に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちChicago Electric Model 90891デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。