ClarionメーカーDPX1001.2の使用説明書/サービス説明書
ページ先へ移動 of 16
OPERAT I ON I NSTALLAT I ON MANUAL 2/1 CHANNEL POWER AMPLIFIER.
DPX1001.2 Power System Amplifier 2 TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Input Connections and Audio Controls . . . . . . .
Owner’s Manual 3 Owner’s Manual • Gold-plated input/output connectors • Aluminum heat sink for efficient heat dissipation • Low profile, compact size for space limited installations • Wire.
DPX1001.2 Power System Amplifier 4 INPUT CONNECTIONS AND AUDIO CONTROLS The front panel of the DPX1001.2 contains connections for RCA Inputs, Speaker Level Inputs and Audio Controls as shown below. The RCA Input Connections are gold-plated RCA jacks and are labeled as RIGHT and LEFT.
Owner’s Manual 5 Use this feature, along with your speaker manufacturer’s recommended crossover frequencies, to quickly design a more advanced system. • X-Over Slope Switch - This switch will change the X-Over between a 12db and 24dB per octave slope.
DPX1001.2 Power System Amplifier 6 APPLICATIONS The Clarion DPX1001.2 2-channel car audio amplifier can be used in a variety of system applications. Here are some examples to help plan your own installation. Figure 3 - In this application the amplifier is bridged for mono operation to drive a subwoofer.
Owner’s Manual 7 Figure 4 - In this application, the amplifier is used in stereo and drives two full-range (or satellite or subwoofer) speakers. NOTE: A passive crossover must be used with satellite speakers. Minimum load in the stereo mode is 1ohm.
DPX1001.2 Power System Amplifier 8 (Set INPUT SELECT Switch to STEREO) Mixed-Mode Satellite and Subwoofer System NOTE: Chart values based on 4 ohm speakers. Figure 5 - The amplifier can be configured for a mixed-mode operation. The table provides component values to create a 6dB per octave crossover at specified frequencies.
Owner’s Manual 9 INSTALLATION This section lists Mounting and Wiring Precautions for installing the Clarion DPX1001.2. These safeguards provide enough detail to complete the installation successfully. If you do not have the necessary skills, Clarion recommends consulting your authorized Clarion dealer for installation.
DPX1001.2 Power System Amplifier 10 5. Add an external fuse on the amplifier’s positive (+) power lead and connect it as close as possible to the vehicle’s (+) battery terminal. Use a fuse rated to the total current consumption of the amplifier(s).
Owner’s Manual 11 Figure 6. - Electrical connections for the DPX1001.2.
DPX1001.2 Power System Amplifier 12 SETTING THE GAIN After completing the installation, follow these steps to set the Gain Control and then perform the Final System Checks. 1. Turn the Gain Control all the way counter-clockwise. 2. Turn the vehicle’s Ignition Switch to the ON position.
Owner’s Manual 13 FINAL SYSTEM CHECKS 1. Start the engine and turn on the source unit. After a two-second delay, slowly increase the Volume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to Troubleshooting.
DPX1001.2 Power System Amplifier 14 Frequency Response Signal Noise Ratio THD Input Sensitivity Low Level Input Sensitivity Speaker Level Max. Power Output Cont. Power Output 2-Ohm Stereo Output Bridged Power Dimensions Current Consumption at output @ max power 20Hz ~ 20kHz >95db .
Owner’s Manual 15 WARRANTY INFORMATION This product is warranted against all defects in material workmanship for a period of one year from the date of original purchase. Clarion ProAudio products except for speakers are covered by a two year warranty when installed by an authorized Clarion dealer.
Clarion Corporation of America 661 W. Redondo Beach Blvd. Gardena, CA 90247-4201 U.S.A. Tel 1.800.GO.CLARION www.clarion.com DPX1001.2 Rev. 1(11/01).
デバイスClarion DPX1001.2の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Clarion DPX1001.2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはClarion DPX1001.2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Clarion DPX1001.2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Clarion DPX1001.2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Clarion DPX1001.2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はClarion DPX1001.2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Clarion DPX1001.2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちClarion DPX1001.2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
