ClarionメーカーMS2106の使用説明書/サービス説明書
ページ先へ移動 of 16
MS2106 MS2106 owner 7-14.qxd 7/14/2003 1:42 PM Page 1.
2 CONTENTS 1. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. Ungo-Net Interface Introduction . . . . . . . . . . . . . . . . . . . . . . . 2 3. Remote Transmitter . . . . . . . . . . . . . . . . . . . .
3 1. FE ATURES Ungo Security Systems are state-of-the-art vehicle protection systems equipped with features designed to: Deter potential intrusions to the vehicle by continually flashing the system LED status indicator while the system is Armed, giving a visual indication to any passer-by that the vehicle is equipped with a security system.
4 1. Ungo-Net Interface Introduction This product is equipped with Ungo’s newest and most revolutionary technology to date, the Ungo-Net bus system. Ungo-Net is a network system that allows expansion, flexibilit y , and superior vehicle security through digital communication.
5 3. REMOTE TRANSMITTER 3.1 Remote Transmitter Layout The Ungo MS2106 comes with 2 Random Code Remote Transmitters used to control the system’s features. Each time a transmitter button is pressed, the LED will flash to indicate that a transmission is taking place.
6 3. SYSTEM OPER ATION 3.1 Arming Operation T o arm the alarm system, press Lock button on the transmitter: • The siren will chirp once. • The parking lights will flash once.* • The doors will lock.* • The LED will come on solid for 5 seconds, and then begin to flash.
7 3.5 Tamper Alert On Disarming, if the system responds with three chirps, indicating the system was triggered, turn on the ignition and the LED will flash the triggered zone 5 cycles.
8 3.10 Remote Panic Feature In the event of an emergency ( PANIC) situation, the system's siren can be triggered for 45 seconds to attract attention. T o activate the Panic feature, press and hold the Lock button for 3 seconds. • The siren will sound.
9 3.12 Valet Mode When placed into Valet Mode the security system will be disabled. However, the optional keyless entry and auxiliary outputs will still function if installed. T o enter the Valet Mode: 1. Be sure the alarm system is disarmed. 2. Press and hold the Valet/Override button.
10 3. Press the Lock button on the transmitter. • The siren will chirp once. 4. Press the Lock button on the transmitter again. • The siren will chirp twice. 5. Repeat steps 3 and 4 for each additional transmitter. 6. Turn OFF the ignition when transmitter programming is complete.
11 4. User Selectable Programming Options The Ungo MS2106 features a user selectable programming table allowing simple adjustments to match the user’s preferences. User Programming Options Table 4.1 User Programmable Options 1. Arming Mode: Selects whether or not the system will automatically Arm when ignition is turned off.
12 7. Remote Start in Valet Mode: Selects whether or not the remote start can be activated when the security system is in Valet mode. (Requires optional Ungo- Net remote start module.) 8. Automatic Starting: Selects whether or not the Ungo-Net start module can be programmed for automatic starting.
13 BUTTON Lock Unlock Trunk Lock Lock then Lock DUR ATION Short Short Long (3 Seconds) Long (3 Seconds) Short then Short FUNCTION Arm Disarm Auxiliary 1 Output Panic Remote Sensor Bypass Reference Charts 3.
14 6. WARRANTY INFORM ATION This Ungo Security System is warranted against defects in material and workmanship. The main unit and remote controls are covered by this limited lifetime warrant y. This Limited Lifetime Warranty applies to Ungo Security systems that have been installed by an authorized Ungo Security dealer.
15 7. INS TALLATION INFORM ATION Date of Installation: Installation Facility: Facility Address: Facility Phone Number: Location of Valet/Override: NOTES MS2106 owner 7-14.
Clarion Corporation of America 661 W. Redondo Beach Blvd. Gardena, CA 90247 www.clarion.com 97-MS2106-10 Re v. 1 (8/03) Ungo Security Corporation, Gardena, CA MS2106 owner 7-14.
デバイスClarion MS2106の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Clarion MS2106をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはClarion MS2106の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Clarion MS2106の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Clarion MS2106で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Clarion MS2106を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はClarion MS2106の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Clarion MS2106に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちClarion MS2106デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。