Cliffordメーカー700-IQの使用説明書/サービス説明書
ページ先へ移動 of 25
Owner' s Manua l World-Clas s Aut o Securit y T M intelliguar d 700-I Q.
All IntelliGuard-IQ Series systems are covered by one or more of the following Clifford Electronics patents: 4,158,874; 4,233,642; 4,327,444; 4,383,242; 4,430,685; 4,845,464; 4,887,064; 4,890,108; 4,9.
Table of Contents Standard Features of the IntelliGuard 7OO-IQ . . . . . . . . . . . . . . . . 3 Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Your 4-button/12-channel remote controls . . . . . . . . . . . . . . . .
Table of Contents (cont.) Remote controlled sensor adjustments . . . . . . . . . . . . . . . . . . . . 15 Remote controlled override of optional sensor #2 . . . . . . . . . . . . . . 15 FACT — False Alarm Control and Test . . . . . . . . . . . . . .
Standard Features of the IntelliGuard 7OO- IQ ✔ Limited Lifetime Warranty — For as long as you own the vehicle, Clifford Electronics will repair or replace the control unit and remote controls free of charge (see the warranty card for full details).
Standard Features of the IntelliGuard 7OO- IQ (cont.) ✔ Remotely Adjustable Dual-Zone Piezo Sensor™ — With just a touch on the remote, you ma y , at any time or place, adjust and test the sensitivity of this microprocessor-controlled solid-state senso r .
Standard Features of the IntelliGuard 7OO- IQ (cont.) ✔ Remote Courtesy Lighting — Automatically turns on your vehicle ’s interior light(s) when you remotely disarm, and keeps them on for 30 seconds or until you start the engine, whichever occurs first.
Standard Features of the IntelliGuard 7OO- IQ (cont.) ✔ Smart Trunk Release Capability — An electronic interlock ensures that the optional remote trunk release can be activated only when the system is disarmed.
Standard Features of the IntelliGuard 7OO- IQ (cont.) ✔ Use r-Selectable Starter/Ignition Interrupt — You may choose either a fault-proof mode, which lets you start the engine even in the unlikely.
Welcome to the world of high-technology vehicle security and convenience C ongratulations on the purchase of your IntelliGuard 700-IQ vehicle security/convenience system. Clifford Electronics has long been recognized as the world’s leading manufacturer of high-technology vehicle security systems and accessories.
Your 4-button/12-channel remote controls The 4-button/12-channel remote controls (one with a gun-metal gray case, the other with a laminated burlwood finish) are ultra-sophisticated miniature radio transmitters powered by a tiny 12-volt battery. Range is up to 100 feet.
What each button/channel does Your IntelliGuard 700-IQ remote controls come pre-programmed so that certain channels command certain functions. If you wish, you can actually assign any channel except 9 through 12 to any function (see pages 20-24).
TO ACTIVATE THE PANIC FEATURE . . . . . . . . . . Press button 1 for 3 seconds. The lights will flash repeatedly and the siren will blare for 30 or 60 seconds (user-selectable), or until you press button 1 again to turn it off.
AntiScan™ Thieves can disarm some other brands of car alarms with a “scanner” that rapidly transmits one remote control code after another. Clifford’s AntiScan will detect any scanner and block the codes it generates.
UltraSecure™ Coded Valet Mode Your secret valet code In seconds, thieves can disable all other alarm brands by hotwiring the ignition and flicking an easy to find “hidden” valet switch. Your IntelliGuard 700 has safeguards that absolutely ensure that a thief cannot enable the valet mode as a way of “turning off” your system.
To exit valet mode 1. Turn the ignition switch to its “ON” position or start the engine. 2. Flick the switch back to its center position. The LED will turn off to confirm that the system is now in its normal operating mode.
Remote controlled sensor adjustments Due to ever-changing conditions, all alarms require periodic fine-tuning of their sensors. An improperly adjusted sensor is the most common cause of false alarms. With other alarms, this requires repeated trips back to the dealer.
Selectable starter/ignition interrupt At the time of installation, you can select whether your IntelliGuard 700-IQ interrupts the starter line or the ignition line. To verify which line is electronically interrupted, enter the vehicle, close the doors, arm the system while inside the vehicle, then try to start the engine.
Smart AutoTesting™ Each time you remotely arm the system, it tests all triggers and sensors. If the hood or trunk is open when you remotely arm, the system will immediately alert you of the problem by sounding 4 chirps and 4 parking light flashes instead of the usual 2 and 2.
3. The LED will blink 1–5 times to indicate the most recently activated point, pause, blink 1–5 times to indicate the next most recently activated point, and so on.
Remote controlled chirp muting: Remote controlled chirp muting capabilities are especially valuable when parking late at night in a quiet residential area or any other time when you want to arm or disarm silently. To arm or disarm silently, simply press button 3 (channel 3) on your remote control instead of the usual button 1 (channel 1).
User-selectable features Your IntelliGuard 700-IQ allows you to set many of its features to your own personal preferences. Although the system’s programming capabilities are very extensive, we have made the programming procedures very simple: to make a change, you just flick the PlainView switch a few times.
EXAMPLE 1: Turn off siren sound number 2: You can turn each of the siren’s six different sound patterns on and off as you wish to create you own custom sound (see the Personalized Siren Sounds section on page 18 for more information) To turn off “Sound 2” you’ll note that “Sound 2” is in column 1, row 2 of the Table (on pages 23-24).
chirps to confirm that the QuietChirps feature is now on. 5. To exit the program mode, turn the ignition off . You’ll hear 3 chirps to confirm program mode exit. You just made three programming changes in only five steps. Easy, isn’t it? Notice again that in step 3 on the previous page you did not have to re-select column 1.
Table of user-selectable features: 1 chirp = OFF, two chirps = ON. Feature Select Column 1 1st latched Column 2 2nd latched Column 3 3rd latched Column 4 4th latched Row 1 1st momentary Sound 1: on /o.
デバイスClifford 700-IQの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Clifford 700-IQをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはClifford 700-IQの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Clifford 700-IQの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Clifford 700-IQで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Clifford 700-IQを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はClifford 700-IQの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Clifford 700-IQに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちClifford 700-IQデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。