Agilent Technologiesメーカー5203の使用説明書/サービス説明書
ページ先へ移動 of 20
A TM M ultimode Fiber Transceivers for SONET OC-3/SDH STM-1 in Low Cost 1x9 P ackage Style T echnical Data Features • Full Compliance with ATM Forum UNI SONET OC-3 Multimode Fiber Physical Layer Spe.
2 design complies with the maximum height allowed for the duplex SC connector over the entire length of the package. The optical subassemblies utilize a high volume assembly process together with low cost lens elements which result in a cost effective building block.
3 DATA OUT SIGNAL DETECT OUT DATA IN ELECTRICAL SUBASSEMBLY QUANTIZER IC DRIVER IC TOP VIEW PIN PHOTODIODE DUPLEX ST RECEPTACLE OPTICAL SUBASSEMBLIES LED PREAMP IC DIFFERENTIAL SINGLE-ENDED DIFFERENTIAL Figure 2. Package Outline Drawing. Figure 1a.
4 Figure 3. Pin Out Diagram. 25.4 (1.000) MAX. 24.8 (0.976) 42 (1.654) MAX. 5.99 (0.236) 12.7 (0.500) 12.0 (0.471) MAX. 0.5 (0.020) 3.3 ± 0.38 (0.130) (± 0.015) + 0.08 - 0.05 + 0.003 - 0.002 + 0.25 - 0.05 + 0.010 - 0.
5 Agilent LED technology has produced 800 nm LED and 1300 nm LED devices with lower aging characteristics than normally associated with these technolo- gies in the industry. The industry convention is 3 dB aging for 800 nm and 1.5 dB aging for 1300 nm LEDs.
6 Figure 5. Transceiver Relative Optical Power Budget at Constant BER vs. Signaling Rate. Figure 6. Bit Error Rate vs. Relative Receiver Input Optical Power. illustrates the typical trade-off between link BER and the receivers input optical power level.
7 NO INTERNAL CONNECTION NO INTERNAL CONNECTION HFBR-520X TOP VIEW V EE RD RD SD V CC V CC TD TD V EE 123456789 C1 C2 L1 L2 R2 R3 R1 R4 C5 C3 C4 R9 R10 V CC FILTER AT V CC PINS TRANSCEIVE.
8 Board Layout - Art W ork The Applications Engineering group is developing Gerber file art work for a multilayer printed circuit board layout incorporating the recommendations above.
9 Electromagnetic Interference (EMI) Most equipment designs utilizing these high speed transceivers from Agilent will be required to meet the requirements of FCC in the United States, CENELEC EN55022 (CISPR 22) in Europe and VCCI in Japan.
10 Figure 10. Relative Input Optical Power vs. Eye Sampling Time Position. Figure 9. Transmitter Output Optical Spectral Width (FWHM) vs. Transmitter Output Optical Center Wavelength and Rise/Fall Times.
11 Transceiver Reliability and Performance Qualification Data The 1 x 9 transceivers have passed Agilent reliability and performance qualification testing and are undergoing ongoing quality monitoring. Details are available from your Agilent sales representative.
12 HFBR-5203, -5204, and -5205 Series Recommended Operating Conditions Parameter Symbol Min. Typ. Max. Unit Reference Ambient Operating Temperature T A 07 0 ° C Supply Voltage V CC 4.75 5.25 V Data Input Voltage - Low V IL - V CC -1.810 -1.475 V Data Input Voltage - High V IH - V CC -1.
13 HFBR-5203, -5204 and -5205 Series Transmitter Electrical Characteristics (T A = 0 ° C to 70 ° C, V CC = 4.75 V to 5.25 V) Parameter Symbol Min. Typ.
14 Agilent offers two such compatible duplex Push-Pull ST connectored jumper cable assemblies to assist you in your evaluation of these products. These cables may be purchased from Agilent with the following part numbers. 1. HFBR-XXX001 A duplex cable 1 meter long assembled with 62.
15 HFBR-5203/-5203T Receiver Optical and Electrical Characteristics (T A = 0 ° C to 70 ° C, V CC = 4.75 V to 5.25 V) Parameter Symbol Min. Typ. Max. Unit Reference Input Optical Power P IN Min. (W) -26 dBm avg. Note 16 Minimum at Window Edge Output Optical Power P IN Min.
16 HFBR-5204/-5204T Receiver Optical and Electrical Characteristics (T A = 0 ° C to 70 ° C, V CC = 4.75 V to 5.25 V) Parameter Symbol Min. Typ. Max. Unit Reference Input Optical Power P IN Min. (W) -29 dBm avg. Note 16 Minimum at Window Edge Figure 10 Input Optical Power P IN Min.
17 HFBR-5205/-5205T Transmitter Optical Characteristics (T A = 0 ° C to 70 ° C, V CC = 4.75 V to 5.25 V) Parameter Symbol Min. Typ. Max. Unit Reference Output Optical Power BOL P O -19 -14 dBm avg. Note 9 62.5/125 µ m, NA = 0.275 Fiber EOL -20 Output Optical Power BOL P O -22.
18 HFBR-5205/-5205T Receiver Optical and Electrical Characteristics (T A = 0 ° C to 70 ° C, V CC = 4.75 V to 5.25 V) Parameter Symbol Min. Typ. Max. Unit Reference Input Optical Power P IN Min. (W) -30 dBm avg. Note 16 Minimum at Window Edge Figure 10 Input Optical Power P IN Min.
19 expressed as a percentage. With the transmitter driven by a 25 MBd (12.5 MHz square-wave) input signal, the average optical power is measured. The data “1” peak power is then calculated by adding 3dB to the measured average optical power.
www.semiconductor.agilent.com Data subject to change. Copyright © 1999 Agilent Technologies, Inc. Obsoletes 5963-5774E (2/95) 5965-9729E (11/99).
デバイスAgilent Technologies 5203の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Agilent Technologies 5203をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAgilent Technologies 5203の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Agilent Technologies 5203の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Agilent Technologies 5203で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Agilent Technologies 5203を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAgilent Technologies 5203の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Agilent Technologies 5203に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAgilent Technologies 5203デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
