CrimeStopperメーカーCS-2003DC SERIES IIの使用説明書/サービス説明書
ページ先へ移動 of 18
CS-2003DC & CS-2003DC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle™ Remote Al arm System by Crimestopper Security Products Inc. This booklet contains the information nece ssary for installing, using, and maintaining your alarm system.
TABLE OF CONTENTS Installation Cautions & Warn ings…….………………………… ……………………………………………………2 Control Module Mounting……… ….…………………………………………… ..……………………….
CONTROL MODULE MOUNTING DO NOT Mount the control unit in the engine compartment! DO NOT Mount the control unit or wiring harness wh ere they can become entangled with moving parts such as brake/gas/clutch peda ls, or the steering column! The alarm control module should be mounted in a concealed location.
WIRING PIN 1: GRAY WIRE: INPUT SOURCE FOR REMOTE OUTPUT 1 RELAY Connect to a +12 Volt or Chassis Grou nd sour ce depending on the output requ ired for PIN 2 Gray wire See Below. PIN 2: GRAY WIRE: REMOTE OUTPUT 1 On-Board Relay (Optional) Connect this wire to an AUX device or Function.
WIRING PIN 11: YELLOW WIRE: IGNITION SWITCHED “ON” +12 VOLTS INPUT Connect to an Ignition Wire (or Fuse in the fuse box) that shows +12 Volts pow er when the key turned “On”, when the car is “Cranking”, and when the car is running.
POWER DOOR LOCK WIRING (ON-BOARD RELAYS) WHITE WIRE: DOOR LOCK [Switch Side, Term 87A] Reverse Polarity and Aftermarket Systems. GREEN: DOOR LOCK OUTPUT [Motor Side, Term 30] Reverse Polarity, Positive , Negative and Aftermarket Systems. BLUE: DOOR UNLOCK OUTPUT [Motor Side , Term 30] Reverse Polarity, Posi tive, Negative and Aftermark et.
SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGA TIV E TRI GGER DO OR LOCKS GREEN DRIVER'S DOOR MOTOR L L UL UL FA C T O R Y L O C K RELA YS +12V + FUSED UNLOCK WIRE CUT +12V FUSED WHITE GREEN BLUE BR.
TRANSMITTER PROGRAMMING This system will learn a maximu m of 3 transmitters total. 1. Turn Ignition ON/OFF…ON/OFF …O N. You should hear (3) chirps. 2. Press the Program/Override Button 5 times and you should hear 5 light flas hes and 5 siren chirps.
OPTION PROGRAMMING PROGRAMMABLE OPTIONS 1. Turn the Ignition ON and press the Override/Pro gram button 5 times. Yo u should hear a long confirmation chirp. 2. Within the next few seco nds, pre ss the Override/Progr am button [again] the number of times that correspon ds to the feature list below.
OPTION PROGRAMMING 1. HORN CHIRPS / PULSES This option controls the system’s Fa ctory Vehicle Horn outp ut. There are 3 selections: Button 1 (Lock) = Horn Pulse only when alarm is tripped. Button 2 (Unlock) = Horn Chirps for Arm / Disa rm and Pulse when tripped.
OPTION PROGRAMMING 9. PARKING LIGHTS ON WITH DISARM Keeps parking lights on instead of 2 flashes when system i s di sarmed to assist i n locating your vehicle in a crowded parking lot or structure. Light will stay on for 30 Sec. or until Ignition is turned on.
CUSTOM OVERRIDE Custom override allows the user to se t a specific number of bu tton presses (2-15) required to perform an emergency override/disarm of the alarm system. This increa ses the level of security of the system, but you MUST MEMORIZE how many button presses you have changed your system to use or the unit will not disarm in an emergency.
OPERATING INSTRUCTIONS ACTIVE ARMING To arm the alarm and lo ck the doors, press the #1 (L ock Symbol) button on the transm itter. You will hear a single siren chirp and the lights will flash once. The system will arm, the do ors will lock and th e starter will be disabled if these optional features are installed.
OPERATING INSTRUCTIONS PROGRAMMABLE SILENT ARM/DISARM MODE The system can be silently armed and disarmed as norma l with Lock/Unlock Buttons, but no siren chirp.
OPERATION OPEN ZONE ALERT/BYPASS If the system detects a faulty or open zone (Door left open) when the system is ACTIVELY ARMED, the siren will chirp 4 times along with 4 light flashes.
CARJACK PROTECTION PASSIVE CARJACK This feature provides Passive Carjack protection and must be enabl ed before use through Alarm programming options (13) & (14).
CS-2003DC SERIES II This page applies to CS2003DC Series II systems ONLY: 5-Button Remote Functions: BANK #1 (Directly Press Buttons) Button 1: Arm Button 2: Disarm Button 3: Aux #1 (Trunk) Button 4: .
CS-2003DC SERIES II DASH UNDER IN DASH Use "L" Bracket OR LED / VALET BUTTON MOUNTING:.
デバイスCrimeStopper CS-2003DC SERIES IIの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
CrimeStopper CS-2003DC SERIES IIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCrimeStopper CS-2003DC SERIES IIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。CrimeStopper CS-2003DC SERIES IIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。CrimeStopper CS-2003DC SERIES IIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
CrimeStopper CS-2003DC SERIES IIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCrimeStopper CS-2003DC SERIES IIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、CrimeStopper CS-2003DC SERIES IIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCrimeStopper CS-2003DC SERIES IIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。