Crimestopper Security ProductsメーカーCS-2014FMの使用説明書/サービス説明書
ページ先へ移動 of 28
INSTALLATION HANDBOOK: CS - 2011RS IV / CS - 2012TW1 / CS - 2014FM / CS - 2016FM INTRODUCTION Congratulations on your choice of a Crimestopper combination alarm & remote engine starter. This installation Handbook covers the following models: CS2011RS IV, CS - 2012TW1, CS - 2014FM & CS - 2016FM.
TABLE OF CONTENTS Pre - Installatio n Considerations…………………...….…...…………...……………………………………………………….2 Cautions & Warnings…….…………………………..…..………………………………………………………………………3 Component Mounting………….
CAUTIONS & WARNINGS DAMAGE RESULTING FROM IMPROPER INSTALLATION IS NOT COVERED UNDER WARRANTY!! DO NOT remote start your vehicle in a closed garage. Make sure that the garage door is open or there is adequate ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes.
Momentary Switch GREEN Optional Turbo Timer Wiring (Not included) WIRING: 9 - PIN Connector Green: MODE A: ( - ) Start Activation Input This wire allows an outside source or accessory to activate a Remote Start. A 1 - second Ground pulse on this wire will trigger a remote start.
WIRING: 9 - PIN Connector M.A.P. can be used to interrupt power/accessory wiring to prevent unauthorized access of t he vehicle’s audio or entertainment systems when Valet Park mode is ON. See Mobile Accessories Protection Diagram below. 86 85 + IGN.
WIRING: 9 - PIN Connector STARTER DISABLE: CUT STARTER WIRE STARTER ORANGE ORANGE CONNECT TO PRE-WIRED OF ALARM IGN. SWITCHED BLUE YELLOW ORANGE WIRE STARTER DISABLE RELAY & SOCKET IGNITION SWITCH.
WIRING: 6 - PIN High Current Connector FUSE RED PINK/WHITE 30A FUSE RED 30A + - BROWN PINK FUEL ENGINE BATTERY PUMP ECU GRAY + STARTER - COIL IGN OR ACC HEAT / AC Diagram not to scale, for illustration purposes only.
WIRING: 3 - PIN Connec tor White/Red: Tachometer Input When installing this system in TACH REFERENCE mode, this wire must be connected to a valid source of AC voltage. This wire allows the unit to sense the engine running. See Tach Section on Page 15 for more information.
WIRING: 5 - PIN Connector Pink: (+12V) +/ - Diesel Glow Plug Input or Car Jack Input (Programmable Input Wire) +/ - Glow Plug Input (Diesel Vehicles Only) Connect Pink wire to indicator circuit that shows a ( - or +) Signal while the “WAIT TO START LAMP” is on.
4-Pin Blue Crimestopper External Data Bus Door Lock Adapter. (Optional) Check Catalog for Part numbers & Applications. (-) UNLOCK (#2) (-) LOCK (-) UNLOCK +12 VDC New Connection for External Modules WIRING: 2 - PIN LED / 2 - PIN Program - Valet Button (22 gauge wires) Mount LED in a visible location on the Dash or Console.
POWER DOOR LOCKS: WIRING & SYSTEM TYPES GREEN: ( - ) LOCK / (+) UNLOCK BLUE: ( - ) UNLOCK / (+) LOCK [READ BELOW FOR COMMON DOOR LOCK TYPES] RED: +12V Coil Power for external relays HINT! This system provides BOTH Positive and Negative Door Lock Outputs on the same set of wires.
DOOR LOCK WIRING NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN RED RED BLUE BLUE DIODES FACTORY FACTORY L L LOCK LOCK POWER POWER LOCKING LOCKING UL UL RELAYS RELAYS UN.
SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGATIVE TRIGGER DOOR LOCKS BLUE/WHITE GREEN RED BLUE DRIVER'S DOOR MOTOR 86 85 L L 87 UL UL 87A 30 FACTORY LOCK RELAYS +12V + FUSED UNLOCK WIRE CUT WIRING .
TACHLESS MODE Your system includes a Tach - less mode that actively monitors and compares the vehicle’s resting voltage versus its running voltage each a remote start is performed; [instead of the conventional tach - pulse method].
TACH MODE & TACH FINDER FEATURE Tach Reference Mode provides reliable remote starting performance though engine speed sensing. When using Tach Reference Mode, the WHITE/RED wire is used for Tach signal [Engine RPM] input. Most modern engines include various points where the Engine Speed [Tach] or A/C signal may be obtained.
TIMED CRANK MODE As an alternative to Tach or Tachless mode, “Timed Crank” provides an additional method of starting the vehicle without locating an exact tach wire. It uses a timed cranking output combined with the use of th e Red/White tach wire as an engine ON/OFF monitor.
DIESEL GLOW PLUG DELAY This feature provi des a solution for diesel vehicles without having to connect to the Glow Plug - “Wait to Start Circuit” input. This may be due to a variety of reasons for example: If your vehicle does not have a viable “Wait to Start Circuit” or you cannot locate and identi fy the circuit.
PROGRAM MABLE OPTIONS TABLE (* = Default) Option # Option Description Option values Lock Button #1 Unlock Button #2 1 Engine Monitoring Tach (Engine RPM)or Tachless Learn Tach *Tachless 2 Auto lock with Ignition ON or OFF.
PROGRAMMABLE OPTIONS Cont. Option # Cont. Option Description Option values Lock Button #1 Unlock Button #2 23 Remote Start Engine Run Time Button #1 = 12 Min.
PROGRAMMABLE OPTIONS 5. PASSIVE LOCKS: This option controls whether the doors will lock when Passive Arming occurs. Note: This may increase the risk of locking keys in the v ehicle.
PROGRAMMABLE OPTIONS 14. LOCK DURING/AFTER REMOTE START: This option controls whether the unit will automatically lock during and after a remot e Start abort or time - out. 15. NO OPTION / NOT USED 16. TIMED CRANK or TACH MONITOR MODE: This option controls whether the system uses a tach wire to control the starter or uses a pre - set cranking time.
PROGRAMMABLE OPTIONS 24. UL TRA - SMART TACHLESS VOLTAGE ADJUSTMENT: This option controls the voltage reference point when using smart Tachless mode. Pressing the Lock or Unlock buttons on the remote raises or lowers the reference level in 1% increments from 80% - %100.
REMOTE PROGRAMMING DIAGRAM IGN OFF WAIT FOR 4 FLASHES PRESS 4X's FLASH 2, 3, or 4 X's (BLUE WIRE GROUNDED) 2-WAY SYSTEMS & ONE WAY CS-2011RS IGN OFF PRESS TOGETHER LOCK & UNLOCK PRES.
2 - VEHICLE OPERATION The CS - 2011RS Series IV, CS - 2014FM and CS - 2016FM systems can be used for 2 car operation. A single remote can control two independent vehicles with identical systems installed, for example, two 2011’s or two 2016’s. NOTE: These systems ARE NOT interchangeable.
5. Press button #2 (Unlock) to reset the options. (Lights should flash twice) 6. T urn Ignition OFF, Close hood (un - ground Blue wire). All features should be set at *DEFAULT values. R EMOTE START TROUBLESHOOTING UNIT CHIRPS 3X, FLASHES LIGHTS ONCE, BUT WILL NOT ATTEMPT A REMOTE START: 1.
J UMPER PIN DIAGRAM JUMPER PLUG SIDE VIEW JUMPER PINS P10/11 JUMPERS: P10 PINK/WHITE = IGN #2 (DEFAULT) P11 PINK/WHITE = ACC #2 IGN2 or ACC2 PINK WHITE for GLOW PLUG PINK WIRE: Jumper Select for Posti.
ANTENNA DIAGRAM WINDSHIELD ANTENNA LOCATIONS CS-2011RS IV 2-WAY SYSTEM Color of plug should match color of socket. 27.
IGNITION 1 ACCESSORY BATTERY STARTER (+) BRAKE SWITCH (-) HOOD /TRUNK SWITCH (+) DOOR SWITCH WHITE IGNITION SWITCH GREEN BLUE 30AMP FUSE BROWN FLASHING ALARM & GREEN RED BLUE (-) LOCK / (+) UNLOCK.
デバイスCrimestopper Security Products CS-2014FMの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Crimestopper Security Products CS-2014FMをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCrimestopper Security Products CS-2014FMの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Crimestopper Security Products CS-2014FMの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Crimestopper Security Products CS-2014FMで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Crimestopper Security Products CS-2014FMを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCrimestopper Security Products CS-2014FMの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Crimestopper Security Products CS-2014FMに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCrimestopper Security Products CS-2014FMデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。