3Mメーカー39800の使用説明書/サービス説明書
ページ先へ移動 of 226
3 3M-Matic 800rf T ype 39800 Automatic Random Case Sealer with AccuGlide II T aping Heads Service Manual Printed in U.S.A. 3M Packaging Systems Division Copyright © 1999, 3M IPC. 3M Center, Building 220-8W-01 3M-Matic and AccuGlide are trademarks of 3M, All right s reserved.
.
T o Our Customers: This is the 3M-Matic /AccuGlide /Scotch brand equipment you ordered. It has been set up and tested in the factory with Scotch brand tapes. If technical assistance or replacement part s are needed, call or Fax the appropriate number listed below .
T o Our Customers: This is the 3M-Matic /AccuGlide /Scotch brand equipment you ordered. It has been set up and tested in the factory with Scotch brand t apes. If any problems occur when operating this equipment, and you desire a ser- vice call, or phone consult ation, call, write, or Fax the appropriate number listed below.
3M-Matic 800rf Case Sealer Revision History Copyright 1999, 3M IPC. All rights reserved. i 3M-Matic 800rf Service Manual Revision History The original issue of this manual and subsequent revisions are identified as follows: Issue date (Rev .
This page intentionally left blank. Revision History 3M-Matic 800rf Case Sealer ii Copyright 1999, 3M IPC. All rights reserved..
Section 1. Description and Specifications 1-1. Intended Use ............................................................................................................... .............................. 1-1 1-2. Description ...........................
3-17. Counter-Balance Pressure Regulator ........................................................................................ .............. 3-14 3-18. Case T op Sensitivity .........................................................................
Section 6. T roubleshooting 6-1. General .................................................................................................................... ................................. 6-1 6-2. T roubleshooting Guide ...........................
Section 8. Preventative Maintenance 8-1. General .................................................................................................................... ................................. 8-1 8-1-1. Maintenance ............................
3M-Matic 800rf Case Sealer Safety Information Copyright 1999, 3M IPC. All rights reserved. vii W arning Label The W ARNING Sharp Knife label, shown in Figure 1, is attached to the orange cut-off knife guard on both taping heads.
Safety Information 3M-Matic 800rf Case Sealer viii Copyright 1999, 3M IPC. All rights reserved. T ape Threading Label The T ape Threading Label, shown in Figure 3, is attached to the left side of both the upper and lower taping heads. This label provides a convenient tape threading diagram.
3M-Matic 800rf Case Sealer W arranty Copyright 1999, 3M IPC. All rights reserved. ix Equipment W arranty and Limited Remedy: THE FOLLOWING W ARRANTY IS MADE IN LIEU OF ALL OTHER W ARRANTIES, E.
W arranty 3M-Matic 800rf Case Sealer x Copyright 1999, 3M IPC. All rights reserved. This page intentionally left blank..
3M-Matic 800rf Case Sealer Description and Specifications T able of Contents 1. Description and Specifications ............................................................................................... ...................... 1-1 1-1. Intended Use .
This page intentionally left blank. Description and Specifications 3M-Matic 800rf Case Sealer 1-ii Copyright 1999, 3M IPC. All rights reserved.
1. Description and Specifications 1-1. Intended Use The 3M-Matic Model 800rf T ype 39800 Automatic Random Case Sealer with AccuGlide II T aping Heads is designed to accept filled, regular slotte.
1-2. Description The 800rf Case Sealer is controlled from two operator control panels located on the front left side of the case sealer . These control panels (Electrical Control Panel and Pneumatic Control Panel) have the most-used controls within easy reach of the operator .
Caution Do not connect a lubricator or lubricated air to this machine. This machine has a non-lubricated air circuit. 3M-Matic 800rf Case Sealer Description and Specifications Copyright 1999, 3M IPC. All rights reserved. 1-3 1-1. Specifications T ape: 3M brand pressure-sensitive film box sealing tapes.
Description and Specifications 3M-Matic 800rf Case Sealer 1-4 Copyright 1999, 3M IPC. All rights reserved. 1-1. Case Sealing Rate Approximation Formula T o determine the case sealing rate for your application: 1. Obtain a representative sample of boxes in the proportion that will be run through the machine.
1-1. Machine Dimensions Figure 1-2 shows machine dimensions for the 800rf Case Sealer . The dimensions are given in both inches and millimeters. For example, 20.00 inches [508 millimeters] is shown as 20.00 [508]. 3M-Matic 800rf Case Sealer Description and Specifications Copyright 1999, 3M IPC.
Description and Specifications 3M-Matic 800rf Case Sealer 1-6 Copyright 1999, 3M IPC. All rights reserved. This page intentionally left blank..
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-i T able of Contents 2. Installation ................................................................................................................. .....
Installation 3M-Matic 800rf Case Sealer 2-ii Copyright 1999, 3M IPC. All rights reserved. This page intentionally left blank..
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-1 2-1. General The following instructions are presented in the order recommended for installing and setting up the 800rf Case Sealer , as well as for learning the operating functions and adjustments.
2-2 Copyright 1999, 3M IPC. All rights reserved. 2-2. Unpacking ü Note It is the responsibility of the customer to uncrate the case sealer . Lifting equipment (forklift, overhead crane, etc.) is necessary to lift the case sealer from its pallet. The case sealer is delivered in one crate.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-3 2-3. Setup Pr ocedure 2-3-1. Case Sealer Bed Height The legs on the case sealer can be adjusted to obtain different bed heights from the factory set-point.
2-4 Copyright 1999, 3M IPC. All rights reserved. 2-3-3. W arning Beacon Installation A red warning beacon is electrically connected to the case sealer , but not mounted to the machine. Install this warning beacon on top of the frame support member to which it is connected.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-5 2-3-5. Air Pressur e Indicator The Pneumatic Control Panel (Figure 2-6) is equipped with an Air Pressure Indicator to show , in red, when the air circuit is energized.
2-6 Copyright 1999, 3M IPC. All rights reserved. 2-3-7. Electrical Connection Caution Before making the electrical connection, make sure that the red Latching Emergency Stop switch located on the Electrical Control Panel is depressed. Also ensure that all p ackaging materials and tools are removed from the case sealer .
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-7 Figure 2-7. Electrical Control Panel (T o p View) Figure 2-8.
2-8 Copyright 1999, 3M IPC. All rights reserved. 2-4. T ape Loading T urn air and electrical supplies off and disconnect before servicing t aping heads. Never attempt to work on the t aping heads or load tape when the box drive system is running. Each taping head is equipped with an extremely sharp cut-off knife.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-9 2-4-1. T op T ape Head Loading 1. T urn of f the Main Disconnect Switch on the Electrical Control Panel. 2. Insert the tape-threading tool downward around the rollers, as shown in Figure 2-10.
2-10 Copyright 1999, 3M IPC. All rights reserved. 2-4-2. Bottom T ape Head Loading The bottom taping head is loaded and threaded in the same manner as the top taping head. For ease in loading, lift the bottom taping head from the con- veyor bed and follow the top tape head loading procedure.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-1 1 2-5. T ape Drum Friction Brake 1. Refer to Figure 2-14. T urn the locking nut clockwise to increase the braking force or coun- terclockwise to decrease the force.
2-12 Copyright 1999, 3M IPC. All rights reserved. 4. Check the Box Centering Pressure gauge on the Pneumatic Control Panel. Refer to Figure 2-15. The gauge should read 40 60 PSIG . If the pressure does not fall within this range, adjust the pressure regulator (CW increases pressure, CCW decreases pressure).
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-13 8. Press the ST AR T button on the Electrical Control Panel.
2-14 Copyright 1999, 3M IPC. All rights reserved. 10. Check the operation of the electrical interlocks for the sliding doors. W ith the drive motors running, move each sliding door , one at a time, from its closed position.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-15 2-6-2. Programmable Contr oller Inputs and Outputs Figure 2-18 shows the SLC 500 Programmable Controller used in the 3M-Matic 800rf T ype 39800 Case Sealer .
2-16 Copyright 1999, 3M IPC. All rights reserved. Figure 2-19 shows the Programmable Controller lights that turn on during the following startup conditions.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-17 T able 2-1 lists the INPUT LEDs displayed on the Programmable Controller , the names of the input signals that feed the LEDs, and the conditions that cause the LEDs to turn ON or OFF .
2-18 Copyright 1999, 3M IPC. All rights reserved. T able 2-2. Programmable Controller Outputs OUTPUT LED Output Signal Name LED Condition 0 Side Belt Lock ON when side belts lock. 1 Side Drive Motors ON when side belt drive motors are running. 2 Flap Folder Arm ON when flap folder arm is down.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-19 2-6-3. Dynamic T ests The following procedures check the actual operation of the 800rf Case Sealer . The following conditions must be observed. • Electrical power and compressed air are available and turned on.
2-20 Copyright 1999, 3M IPC. All rights reserved. 2-7. Placing 800rf Case Sealer in P r oduction Line When installing the 800rf Case Sealer into a produc- tion line, ensure compliance with the following requirements: • The case sealer must be level.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-21 2-8. Special Setup Pr ocedure 2-8-1. Relocating Pneumatic and Electrical Contr ol Panels T urn off electrical power and air supply and disconnect power cord from electrical supply before beginning this procedure.
2-22 Copyright 1999, 3M IPC. All rights reserved. 3. Disconnect the plastic conduit at the Electrical Control Panel, which connects to the Pneumatic Control Panel. This conduit contains the electri- cal wires for the valve solenoids. 4. Slide the left front sliding door all the way to the right to provide additional access.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-23 8. Remove the left and right mainframe brackets that support the Pneumatic Control Panel.
2-24 Copyright 1999, 3M IPC. All rights reserved. Figure 2-25. Moving Support Brackets for Pneumatic Control Panel Installation 3M-Matic 800rf Case Sealer.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-25 Installing Air On/Off V alve/Regulator/Filter 13. Locate the Air On/Off V alve/Regulator/Filter and bracket. 14. Rotate the bracket 180°. a. Remove the lower socket-head screw (4 mm) and loosen the upper screw , but do not remove it.
2-26 Copyright 1999, 3M IPC. All rights reserved. 16. Remove and separate the Air On/Off V alve from the Regulator/Filter . a. Loosen the hex screw in the bracket that holds the two assemblies together . Refer to Figure 2-28. b. Separate the Air On/Off V alve from the Regulator/Filter by removing both assem- blies from the bracket.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-27 19. Connect the air line from the Pneumatic Control Panel to the air outlet on the regulator body . a. Open the Pneumatic Control Panel (8 mm hex wrench) and remove the center of the left knockout grommet.
2-28 Copyright 1999, 3M IPC. All rights reserved. Removing Electrical Contr ol Panel 20. Remove the Electrical Control Panel. This step requires two people. a. Disconnect the large electrical connector and the two smaller infeed motor electrical connectors located under the Electrical Control Panel.
3M-Matic 800rf Case Sealer Installation Copyright 1999, 3M IPC. All rights reserved. 2-28 23. Remove the mainframe bracket and E-St op switch from the rear left of the machine and install the mainframe bracket at the front right of the case sealer .
2-30 Copyright 1999, 3M IPC. All rights reserved. 26. Connect the electrical connectors and cables to the Electrical Control Panel. a. Route the electrical connectors and cables through the undercarriage to the rear of the case sealer .
T able of Contents 3. Adjustments .................................................................................................................. ................................. 3-1 3-1. Case Sealer Bed Height ....................................
Adjustments 3M-Matic 800rf Case Sealer 3-ii Copyright 1999, 3M IPC. All rights reserved. 3-28. Low Air Pressure Switch ................................................................................................... .............. 3-22 3-29.
3. 3M-Matic 800rf Case Sealer Adjustments Copyright 1999, 3M IPC. All rights reserved. 3-1 3. Adjustments 3-1. Case Sealer Bed Height Specification Adjust the case sealer bed height so that it is the same height as the conveyor line to which it is attached.
Adjustments 3M-Matic 800rf Case Sealer 3-2 Copyright 1999, 3M IPC. All rights reserved. 3-2. Pneumatic Device Factory Set Points T able 3-1 lists the factory set points for regulator pressure controls, Pneumatic Control Panel mounted speed controls, and cylinder mounted speed controls.
T able 3-1. Pneumatic Device Factory Set Points and Adjustment Locations (Continued) Cylinder Mounted Speed Controls Air Rate Exhaust Restriction Controls (Speed Controls) Set V alue Adjustment Locati.
Adjustments 3M-Matic 800rf Case Sealer 3-4 Copyright 1999, 3M IPC. All rights reserved. 3-3. Main Air Pressur e Regulator Specification The case sealer requires a compressed air supply of 75 140 PSIG [5.2 9.5 BAR] 7.0 SCFM [1 1.89 m 3 /h, 21 o C, 101 kPa] maximum at maximum cycle rate.
3M-Matic 800rf Case Sealer Adjustments Copyright 1999, 3M IPC. All rights reserved. 3-5 3-5. Side Belt Pr essur e Regulator Specification The side belt pressure should be set so that cases are driven smoothly through the sealing process by the belts without the cases being deformed by excessive side pressure.
Adjustments 3M-Matic 800rf Case Sealer 3-6 Copyright 1999, 3M IPC. All rights reserved. 3-7. Side Belts In/Out Rates This is not a r outine adjustment.
3M-Matic 800rf Case Sealer Adjustments Copyright 1999, 3M IPC. All rights reserved. 3-7 3-8. Side Belt Inner Limit This is not a r outine adjustment.
3-9. Side Belt T ension This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification Adjust the tension of the side belts so that the cases move through the machine positively and the belts wrap tightly around the surface of the idler pulleys at each end of the frame.
3-10. Motor Drive Belts, Upper and Lower This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification Adjust the motor drive belts to maintain proper belt tension. Adjustment W arning T urn the main air supply and electrical power off before making this adjustment.
3-1 1. Drive Chain This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification There is no exact chain tension specification. Adjust the chain so that it is just tight enough to drive reliably without slack.
3-13. Flap Folder Arm and Flap Folder Flow Controls - Speed Contr ols This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification Adjust the cylinder-mounted speed flow controls for optimum stroke operation.
Adjustments 3M-Matic 800rf Case Sealer 3-12 Copyright 1999, 3M IPC. All rights reserved. Figure 3-15. Flap Folder Arm Reed Switch Adjustment Adjustment 1. Observe when the Flap Folder activates. It should begin to move downward when the Flap Folder Arm is about midway between fully extended and fully retracted.
3M-Matic 800rf Case Sealer Adjustments Copyright 1999, 3M IPC. All rights reserved. 3-13 3-15. Cylinder Cushion Setting ü Note This is a generic approach to adjusting the cylinder cushion settings for all cylinders used in the 800rf Case Sealer .
Adjustments 3M-Matic 800rf Case Sealer 3-14 Copyright 1999, 3M IPC. All rights reserved. 3-17. Counter-Balance Pr essur e Regulator Specification The Counter-Balance Pressure Regulator should be set so the upper head assembly comes to a stop between 0 and 1/8 inch from the top of the carton.
3M-Matic 800rf Case Sealer Adjustments Copyright 1999, 3M IPC. All rights reserved. 3-15 3-19. Fork Lift Flow Controls-Speed Controls These cylinder-mounted speed flow controls ar e factory set and normally do not need adjusting unless r elated components ar e r eplaced.
Adjustments 3M-Matic 800rf Case Sealer 3-16 Copyright 1999, 3M IPC. All rights reserved. 3-20. Infeed Box S top-Gate Flow Contr ol- Speed Control This cylinder-mounted speed flow control is factory set and normally does not need adjusting unless the cylinder is replaced.
3M-Matic 800rf Case Sealer Adjustments Copyright 1999, 3M IPC. All rights reserved. 3-17 3-21. Box Centering Rails In/Out Rates This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components.
Adjustments 3M-Matic 800rf Case Sealer 3-18 Copyright 1999, 3M IPC. All rights reserved. 3-22. Upper Head Assembly Down/Up Rates This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components.
3M-Matic 800rf Case Sealer Adjustments Copyright 1999, 3M IPC. All rights reserved. 3-19 3-23. T op Flap Compression Rollers Specification Adjust the top flap compression rollers to hold the top flaps of the case together during the taping process.
Adjustments 3M-Matic 800rf Case Sealer 3-20 Copyright 1999, 3M IPC. All rights reserved. 3-25. T ape Drum Friction Brake Specification Adjust the tape drum friction brake to prevent exces- sive tape overtravel caused by a flywheel effect. Adjustment 1.
3M-Matic 800rf Case Sealer Adjustments Copyright 1999, 3M IPC. All rights reserved. 3-21 3-27. One-W ay T ension Roller Specification Adjust the one-way tension roller so that it slips under a tangential force of 1 to 2 lbs. [0.5 to 0.9 kg]. Refer to Figure 3-27.
Adjustments 3M-Matic 800rf Case Sealer 3-22 Copyright 1999, 3M IPC. All rights reserved. 3-28. Low Air P r essure Switch Specification Adjust the Low Air Pressure Switch so the case sealer shuts down if the main air pressure drops below 50 PSIG and a box feed is attempted.
3M-Matic 800rf Case Sealer Adjustments Copyright 1999, 3M IPC. All rights reserved. 3-23 3-29. Overload Circuit Br eaker Specification Adjust the setting screw on the Overload Circuit Breaker to the 1.4 Amp setting. Adjustment Use a Phillips-head screwdriver to set the alignment mark to the 1.
Adjustments 3M-Matic 800rf Case Sealer 3-24 Copyright 1999, 3M IPC. All rights reserved. This page intentionally left blank..
3M-Matic 800rf Case Sealer Disassembly/Reassembly 3M 1998 December 4-i T able of Contents 4. Disassembly/Reassembly ....................................................................................................... .......................
Disassembly/Reassembly 3M-Matic 800rf Case Sealer 4-ii 3M 1998 December This page intentionally left blank..
3M-Matic 800rf Case Sealer Disassembly/Reassembly 3M 1998 December 4-1 4. Disassembly/Reassembly 4-1. General This section provides instructions for removing components and major assemblies from the Model 800rf T ype 39800 Case Sealer . Disassembly should be done only to replace a faulty part.
Disassembly/Reassembly 3M-Matic 800rf Case Sealer 4-2 3M 1998 December 4-3. Side Drive Belt Assembly T urn off the main air supply and electrical power before removing any components .
3M-Matic 800rf Case Sealer Disassembly/Reassembly 3M 1998 December 4-3 4-4. Side Drive Belt W arning T urn off the main air supply and electrical power before removing any components . 1. Remove the side drive belt assembly using Procedure 4-3 in this section.
Disassembly/Reassembly 3M-Matic 800rf Case Sealer 4-4 3M 1998 December 4-5. M otor Drive Belts, Upper and Lower T urn off the main air supply and electrical power before removing any components . ü Note A gear puller is needed to complete this procedure.
3M-Matic 800rf Case Sealer Disassembly/Reassembly 3M 1998 December 4-5.
Disassembly/Reassembly 3M-Matic 800rf Case Sealer 4-6 3M 1998 December 4-6. Case Sealer Bed Plates T urn off the main air supply and electrical power before removing any components . 1. Remove the side drive belt assembly using Procedure 4-3 in this section.
3M-Matic 800rf Case Sealer Disassembly/Reassembly 3M 1998 December 4-7 4-7. Fork Cylinder ng T urn off the main air supply and electrical power before removing any component s. 1. Remove the case sealer bed plates using Procedures 4-3 and 4-6 in this section.
Disassembly/Reassembly 3M-Matic 800rf Case Sealer 4-8 3M 1998 December 4-9. Flap Folder Cylinder T urn off the main air supply and electrical power before removing any components . Steps 1 through 3 on the figure below refer to removal of the Flap Folder Cylinder .
3M-Matic 800rf Case Sealer Disassembly/Reassembly 3M 1998 December 4-9 4-1 1. Knife Replacement, Upper T aping Head The T ape Cut-Off Knife is very sharp. T o avoid personal injury , handle the knife with special care. Also, disconnect the power before starting this procedure.
Disassembly/Reassembly 3M-Matic 800rf Case Sealer 4-10 3M 1998 December 4-12. Knife Replacement, Lower T aping Head The T ape Cut-Off Knife is very sharp. T o avoid personal injury , handle the knife with special care. Also, disconnect the power before starting this procedure.
3M-Matic 800rf Case Sealer Disassembly/Reassembly 3M 1998 December 4-1 1 12. T o reassemble and reinstall the side drive belt assembly , perform steps 1 through 9 in reverse order . 13. When the side drive belt assembly has been reassembled and reinstalled, perform the follow- ing adjustment procedures described in Section 3.
Disassembly/Reassembly 3M-Matic 800rf Case Sealer 4-12 3M 1998 December 4-14. Infeed Rollers 1. Remove the photocell connectors [40] from photocells PC1 and PC2. 2. Remove the front photocell support bracket [34] secured by 3 hex-head screws. 3.
3M-Matic 800rf Case Sealer Disassembly/Reassembly 3M 1998 December 4-13.
Disassembly/Reassembly 3M-Matic 800rf Case Sealer 4-14 3M 1998 December 4-15. Overload Circuit Br eaker 1. Pull and hold down on the silver release clip located at the bottom and rear of the circuit breaker . Refer to the figure below . 2. Pull outward on the bottom of the circuit breaker and lift up and away from the DIN rail.
3M-Matic 800rf Case Sealer Theory of Operation Copyright 1999, 3M IPC. All rights reserved. 5-i T able of Contents 5. Theory of Operation .........................................................................................................
Theory of Operation 3M-Matic 800rf Case Sealer 5-ii Copyright 1999, 3M IPC. All rights reserved. This page intentionally left blank.
3M-Matic 800rf Case Sealer Theory of Operation Copyright 1999, 3M IPC. All rights reserved. 5-1 5. Theory of Operation 5-1. General This section begins with an operation summary , which gives an overview of the operations that the Model 800rf T ype 39800 Case Sealer performs as it seals a carton.
Theory of Operation 3M-Matic 800rf Case Sealer 5-2 Copyright 1999, 3M IPC. All rights reserved. During normal operation, as the box exits the case sealer it blocks the light path of the sixth photocell momentarily . When the box clears this light path, the controller allows the next box to enter the machine.
3M-Matic 800rf Case Sealer Theory of Operation Copyright 1999, 3M IPC. All rights reserved. 5-3 T able 5-1. Sequence T able Random Mode SEQUENCE RANDOM MODE PLC V A L VE ACTION OUTPUT .
Theory of Operation 3M-Matic 800rf Case Sealer 5-4 Copyright 1999, 3M IPC. All rights reserved. T able 5-1. Sequence T able Random Mode (continued) SEQUENCE RANDOM MODE PLC V AL VE ACT.
3M-Matic 800rf Case Sealer Theory of Operation Copyright 1999, 3M IPC. All rights reserved. 5-5 T able 5-1. Sequence T able Random Mode (continued) SEQUENCE RANDOM MODE PLC V AL VE ACT.
Theory of Operation 3M-Matic 800rf Case Sealer 5-6 Copyright 1999, 3M IPC. All rights reserved. T able 5-1. Sequence T able Random Mode (continued) SEQUENCE RANDOM MODE PLC V AL VE ACT.
3M-Matic 800rf Case Sealer Theory of Operation Copyright 1999, 3M IPC. All rights reserved. 5-7 T able 5-2. Sequence T able Fixed Mode SEQUENCE FIXED MODE PLC V AL VE ACTION OUTPUT INP.
Theory of Operation 3M-Matic 800rf Case Sealer 5-8 Copyright 1999, 3M IPC. All rights reserved. T able 5-2. Sequence T able Fixed Mode (continued) SEQUENCE FIXED MODE PLC V AL VE ACTION OUTPUT INPUT IF ST AR T BUTT ON IS PUSHED PROGRAM GOES T O STEP 1 1 STEP 1 ST A R T T23 (0.
3M-Matic 800rf Case Sealer Theory of Operation Copyright 1999, 3M IPC. All rights reserved. 5-9 T able 5-2. Sequence T able Fixed Mode (continued) SEQUENCE FIXED MODE PLC V AL VE ACTION OUTPUT INPUT IF T2 T IMED OUT PROGRAM GOES T O STEP 6 STEP 6 SIDE DRIVE ASSEMBL Y LOCKS LA TCH V2 TURN ON 0 ST AR T T5 (15.
Theory of Operation 3M-Matic 800rf Case Sealer 5-10 Copyright 1999, 3M IPC. All rights reserved. This page intentionally left blank..
This page intentionally left blank. 3M-Matic 800rf Case Sealer Theory of Operation Copyright 1999, 3M IPC. All rights reserved. 5-11 T able 5-3.
Theory of Operation 3M-Matic 800rf Case Sealer 5-12 Copyright 1999, 3M IPC. All rights reserved. T able 5-3. Sequence T able Bypass Mode (continued) SEQUENCE BYP ASS MODE PLC V AL VE A.
3M-Matic 800rf Case Sealer Theory of Operation Copyright 1999, 3M IPC. All rights reserved. 5-13 T able 5-3. Sequence T able Bypass Mode (continued) SEQUENCE BYP ASS MODE PLC V AL VE A.
Theory of Operation 3M-Matic 800rf Case Sealer 5-14 Copyright 1999, 3M IPC. All rights reserved. 5-4. Electrical System When reading about the electrical system, refer to the 800rf Electrical Schematic in Subsection 5-4-3.
3M-Matic 800rf Case Sealer Theory of Operation Copyright 1999, 3M IPC. All rights reserved. 5-15 Photocells Six photocells positioned along the left side (front) of the case sealer detect the presence of boxes as they pass through the case sealer .
Theory of Operation 3M-Matic 800rf Case Sealer 5-16 Copyright 1999, 3M IPC. All rights reserved. 1-1-3. Electrical Schematic The 800rf Electrical Schematic is shown on three pages, which are labeled 1 of 3, 2 of 3, and 3 of 3.
3M-Matic 800rf Case Sealer Theory of Operation Copyright 1999, 3M IPC. All rights reserved. 5-17.
Theory of Operation 3M-Matic 800rf Case Sealer 5-18 Copyright 1999, 3M IPC. All rights reserved..
3M-Matic 800rf Case Sealer Theory of Operation Copyright 1999, 3M IPC. All rights reserved. 5-19.
Theory of Operation 3M-Matic 800rf Case Sealer 5-20 Copyright 1999, 3M IPC. All rights reserved. 5.5 Pneumatic System When reading about the pneumatic system, refer to the 800rf Pneumatic Diagram on the next page.
3M-Matic 800rf Case Sealer T roubleshooting Copyright 1999, 3M IPC. All rights reserved. 6-i T able of Contents 6. T roubleshooting .............................................................................................................. .
T roubleshooting 3M-Matic 800rf Case Sealer 6-ii Copyright 1999, 3M IPC. All rights reserved. This page intentionally left blank..
3M-Matic 800rf Case Sealer T roubleshooting Copyright 1999, 3M IPC. All rights reserved. 6-1 6-1. General Read the Theory of Operation in Section 5, so that the operational characteristics of the machine are understood.
Problem Cause Correction Box rear flap pulled back out of box. Rear flap folder out of adjustment. Adjust Rear Flap Folder (refer to Section 3). Flaps not positioned properly before entering case sealer . Position flaps properly . Front of box crushed by upper Paddle is not returning after Adjust Paddle Pressure Regulator head assembly .
3M-Matic 800rf Case Sealer T roubleshooting Copyright 1999, 3M IPC. All rights reserved. 6-3 Problem Cause Correction Blade does not cut tape or tape end Adhesive has built up on blade. Clean blade. is jagged or shredded. (continued) Cutoff force is not sufficient.
T roubleshooting 3M-Matic 800rf Case Sealer 6-4 Copyright 1999, 3M IPC. All rights reserved. Problem Cause Correction T ape end does not stay in T ape is threaded incorrectly .
3M-Matic 800rf Case Sealer T roubleshooting Copyright 1999, 3M IPC. All rights reserved. 6-5 Problem Cause Correction T ape edge folds over, providing an T ape drum is not aligned. Adjust T ape W eb Alignment unsatisfactory seal. (refer to Section 3).
T roubleshooting 3M-Matic 800rf Case Sealer 6-6 Copyright 1999, 3M IPC. All rights reserved. 6-3. Pneumatic Component T esting Using the solenoid actuated valves, located in the Pneumatic Control Panel, you can manually actuate the valves that initiate the operation of other pneumatic components within the Model 800rf Case Sealer .
3M-Matic 800rf Case Sealer T roubleshooting Copyright 1999, 3M IPC. All rights reserved. 6-7 The following table lists the pneumatic valves and describes the function of each valve. T o avoid injury to yourself or others, never actuate a pneumatic valve unless everyone is clear of the machine.
T roubleshooting 3M-Matic 800rf Case Sealer 6-8 Copyright 1999, 3M IPC. All rights reserved. 6-4. Electrical Cir cuit Fault Conditions The Model 800rf Case Sealer displays electrical circuit fault conditions on the Electrical Control Panel with red light indicators along with a red beacon light on a light pole.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-i T able of Contents 7. Illustrated Parts Br eakdown ........................................................................................
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-ii Copyright 1999, 3M IPC. All rights reserved. Figure 7-28. Applying Assembly for Upper and Lower Heads ................................................ 7-74 Figure 7-29. Buffing Assembly for Upper Head .
7. Illustrated Parts Breakdown 7-1. How to Order Replacement Parts 1. Refer to the following figures and their related lists of parts on the following pages to determine the individual part number and description. ü Note Complete descriptions have been included for most commercially available components.
7-4. Illustrations and Parts Lists Figure 7-1. 800rf Case Sealer Breakdown Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-2 Copyright 1999, 3M IPC.
This page intentionally left blank. 3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-3.
Figure 7-2. Conveyor Frame Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-4 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Conveyor Frame Item Part Number Number Description Qty 1 ................ 78-8119-8588-2 ............ BED ASSEMBL Y , Conveyor .............................................................. ......... 1 2 ................ 78-8076-5038-3 ..
Parts List - Conveyor Frame (Continued) Item Part Number Number Description Qty 67 .............. 78-8060-7873-5 ............ PLUG , Female ......................................................................... ...................... 2 68 .........
This page intentionally left blank. 3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-7.
Figure 7-3. Conveyor Center Bed and Fork Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-8 Copyright 1999, 3M IPC. All rights reserved.
Parts List - Conveyor Center Bed and Fork Item Part Number Number Description Qty 15 .............. 26-1003-7963-0 ............ SCREW , Soc. Hd., M8 x 16 ............................................................. .......... 10 18 .............. 78-8017-9318-9 .
Figure 7-4. Conveyor Bed Rollers Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-10 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Conveyor Bed Rollers Item Part Number Number Description Qty 41 .............. 78-80178060-92577803-92 SCREW , Phillips Head, M4 x 10RIVET .............................................. 20 42 .............. 26-1003-6914-4 ............ NUT , Plastic Insert, M4 .
Figure 7-5. Side Belt Centering Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-12 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Side Belt Centering Item Part Number Number Description Qty 1 ................ 78-8114-4867-5 ............ ARM ASSEMBL Y , Front, Right .......................................................... ........ 1 2 ................ 78-8114-4868-3 .
Parts List - Side Belt Centering (Continued) Item Part Number Number Description Qty 34 .............. 78-8060-7533-5 ............ LOCK RING ............................................................................ ..................... 2 35 ......
This page intentionally left blank. 3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-15.
Figure 7-6. Column Assembly Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-16 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Column Assembly Item Part Number Number Description Qty 1 ................ 78-8114-5096-0 ............ COLUMN ASSEMBL Y , Right ..................................................................... 1 2 ................ 78-8114-5097-8 ....
Figure 7-7. Flap Folder Assembly Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-18 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Flap Folder Assembly Item Part Number Number Description Qty 1 ................ 78-8119-8502-3 ............ SUPPOR T , Flap Folder ................................................................ ................. 1 2 ................ 26-1003-7963-0 .
Parts List - Flap Folder Assembly (Continued) Item Part Number Number Description Qty 34 .............. 78-8060-7896-6 ............ SCREW , Soc. Hd., Hex Hd., M6 x 14 .......................................................... 2 35 .............. 78-8060-7885-9 .
This page intentionally left blank. 3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-21.
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-22 Copyright 1999, 3M IPC. All rights reserved. Figure 7-8. Paddle Assembly.
Parts List - Paddle Assembly Item Part Number Number Description Qty 1 ................ 78-8119-8507-2 ............ SUPPOR T ASSEMBL Y , Guide, Right ...................................................... ... 1 2 ................ 78-8119-8508-0 ......
Figure 7-9. Side Belt Rail Assembly Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-24 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Side Belt Rail Assembly Item Part Number Number Description Qty 1 ................ 78-8114-4904-6 ............ SIDE FLAP FOLDER, Right ............................................................. .......... 1 2 ................ 78-8076-5083-9 .
Figure 7-10. Head Cylinder Assembly Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-26 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Head Cylinder Assembly Item Part Number Number Description Qty 1 ................ 78-8057-5747-9 ............ MOUNT , Cylinder Rod End ......................................................................... 2 2 ................ 26-1003-6918-5 .
Figure 7-1 1. Upper T ape Head Mount Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-28 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Upper T ape Head Mount Item Part Number Number Description Qty 1 ................ 78-8122-6717-3 ............ FRAME, Right, Upper Head, w/English Label ........................................... .1 2 ................ 78-8122-6718-1 .....
Figure 7-12. Upper T ape Drum Bracket Assembly Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-30 Copyright 1999, 3M IPC. All rights reserved.
Parts List - Up per T ape Drum Bracket Assembly Item Part Number Number Description Qty 1 ................ 78-8094-6446-0 ............ BRACKET ASSEMBL Y , Core Holder ....................................................... .. 1 2 ................ 78-8091-0605-3 .
Figure 7-13. Side Belt and Drive Assemblies Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-32 Copyright 1999, 3M IPC. All rights reserved.
Parts List - Side Belt and Drive Assemblies Item Part Number Number Description Qty 1 ................ 78-8119-8513-0 ............ DRIVE ASSEMBL Y , Side, Right, w/o Motor .............................................. 1 2 ................ 78-8119-8514-8 .
Parts List - Side Belt and Drive Assemblies (Continued) Item Part Number Number Description Qty 64 .............. 78-8094-6472-6 ............ MOT OR, 200/220V , 50/60Hz ....................................................................... 2 65 .....
This page intentionally left blank. 3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-35.
Figure 7-14. Side Belt Drive Pulleys (Detail) Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-36 Copyright 1999, 3M IPC. All rights reserved.
Parts List - Side Belt Drive Pulleys (Detail) Item Part Number Number Description Qty 15 .............. 78-8060-8000-4 ............ DRIVE PULLEY ASSEMBL Y ................................................................ .... 2 16 .............. 78-8076-5105-0 .
Figure 7-15. Upper Head Conduit Assembly Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-38 Copyright 1999, 3M IPC. All rights reserved.
Parts List - Upper Head Conduit Assembly Item Part Number Number Description Qty 1 ................ 78-8100-0897-5 ............ HOUSING , W ire ....................................................................... .................... 1 2 ..........
Figure 7-16. Electrical Contr ol Panel Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-40 Copyright 1999, 3M IPC. All rights reserved.
Parts List - Electrical Control Panel Item Part Number Number Description Qty 1 ................ 78-8122-6719-9 ............ BOX, Electric w/English Label ....................................................... ............. 1 2 ................ 78-8119-8591-6 .
Parts List - Electrical Control Panel (Continued) Item Part Number Number Description Qty 34 .............. 78-8076-5123-3 ............ PLUG , CNE 24FSN ...................................................................... ................ 1 35 .....
This page intentionally left blank. 3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-43.
Figure 7-17. Electrical Control Panel (Detail) Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-44 Copyright 1999, 3M IPC. All rights reserved.
Parts List - Electrical Control Panel (Detail) Item Part Number Number Description Qty 1 ................ 78-8100-0898-3 ............ SWITCH ASSEMBL Y , LA2-16 ................................................................... 1 2 ................ 78-8060-7622-6 .
Figure 7-18. Pneumatic Control Panel Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-46 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Pneumatic Contr ol Panel Item Part Number Number Description Qty 1 ................ 78-8122-6721-5 ............ BOX, Pneumatics w/English Label .............................................................. 1 2 ................ 78-8119-8554-4 .
Figure 7-19. Pneumatic Components, #1 Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-48 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Pneumatic Components, #1 Item Part Number Number Description Qty 1 ................ 78-8119-8605-4 ............ FIL TER/REGULA T OR ASSEMBL Y ........................................................... 1 10 .............. 78-8119-8612-0 .
Figure 7-20. Pneumatic Components, #2 Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-50 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Pneumatic Components, #2 Item Part Number Number Description Qty 47 .............. 78-8091-0350-6 ............ UNION, Special ....................................................................... ..................... 8 48 .............
Figure 7-21. Pneumatic Components, #3 Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-52 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Pneumatic Components, #3 Item Part Number Number Description Qty 1 ................ 78-8119-8605-4 ............ FIL TER/REGULA T OR ASSEMBL Y ........................................................... 1 2 ................ 78-8119-8606-2 .
Parts List - Pneumatic Components, #3 (Continued) Item Part Number Number Description Qty 37 .............. 78-8119-8632-8 ............ GAUGE, 50, 0-12 Bar .................................................................. ................ 3 38 ......
Parts List - Pneumatic Components, #3 (Continued) Item Part Number Number Description Qty 77 .............. 78-8119-8659-1 ............ SIDE DRIVE, Air Cylinder Assembly .................................................... ..... 1 78 .............. 78-8119-8660-9 .
Figure 7-22. Sliding Door Assembly Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-56 Copyright 1999, 3M IPC. All rights reserved..
Parts List - Sliding Door Assembly Item Part Number Number Description Qty 1 ................ 78-8119-8568-4 ............ FRAME, Right, Guards ................................................................ ................ 1 2 ................ 78-8119-8670-8 .
Parts List - Sliding Door Assembly (Continued) Item Part Number Number Description Qty 34 .............. 78-8010-7416-8 ............ NUT , Metric, Hex, S teel, M4 .......................................................... ............. 2 35 ..........
This page intentionally left blank. 3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-59.
Figure 7-23. Infeed Conveyor Frame Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-60 Copyright 1999, 3M IPC. All rights reserved..
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-61 Parts List - Infeed Conveyor Frame Item Part Number Number Description Qty 1 ................ 78-8114-4812-1 ............ CONVEYER FRAME ASSEMBL Y .
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-62 Copyright 1999, 3M IPC. All rights reserved. Parts List - Infeed Conveyor Frame (Continued) Item Part Number Number Description Qty 34 .............. 78-8114-4823-8 ............ SUPPOR T , Photocell/Reflector .
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-63 This page intentionally left blank..
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-64 Copyright 1999, 3M IPC. All rights reserved. Figure 7-24. Infeed Conveyor Drive Assembly.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-65 Parts List - Infeed Conveyor Drive Assembly Item Part Number Number Description Qty 1 ................ 78-8114-4827-9 ............ GEARBOX, NMR V40, i20, P AM63, B5 .
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-66 Copyright 1999, 3M IPC. All rights reserved. Figure 7-25. Infeed Conveyor Centering Assembly.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-67 Parts List - Infeed Conveyor Centering Assembly Item Part Number Number Description Qty 1 ................ 78-81 14-4837-8 ............ BOX .
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-68 Copyright 1999, 3M IPC. All rights reserved. Parts List - Infeed Conveyor Centering Assembly (Continued) Item Part Number Number Description Qty 34 .............. 78-8054-8779-6 .....
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-69 This page intentionally left blank..
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-70 Copyright 1999, 3M IPC. All rights reserved. Figure 7-26. T aping Head Assemblies - AccuGlide Ô II STD 2-Inch.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-71 This page intentionally left blank..
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-72 Copyright 1999, 3M IPC. All rights reserved. Figure 7-27. Frame Assembly for Upper Head.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-73 Parts List Frame Assembly for Upper Head Item Part Number Number Description Qty 1 ................ 78-8070-1386-3 ............ FRAME, T ape Mount Upper Assembly .
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-74 Copyright 1999, 3M IPC. All rights reserved. Figure 7-28. Applying Assembly for Upper and Lower Heads.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-75 Parts List Applying Assembly for Upper and Lower Heads Item Part Number Number Description Qty 1 ................ 78-8070-1206-3 .....
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-76 Copyright 1999, 3M IPC. All rights reserved. Figure 7-29. Buffing Assembly for Upper Head.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-77 Parts List Buffing Assembly for Upper Head Item Part Number Number Description Qty 1 ................ 78-8070-1392-1 ............ BUFFING ARM, Sub Assembly .
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-78 Copyright 1999, 3M IPC. All rights reserved. Figure 7-30. Link Assembly for Upper and Lower Heads.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-79 Parts List Link Assembly for Upper and Lower Heads Item Part Number Number Description Qty 1 ................ 78-8070-1388-9 .........
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-80 Copyright 1999, 3M IPC. All rights reserved. Figure 7-31. Knife Assembly for Upper and Lower Heads.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-81 Parts List Knife Assembly for Upper and Lower Heads Item Part Number Number Description Qty 1 ................ 78-8070-1217-0 ........
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-82 Copyright 1999, 3M IPC. All rights reserved. Figure 7-32. T ape Drum and Bracket for Upper and Lower Heads.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-83 Parts List T ape Drum and Bracket for Upper and Lower Heads Item Part Number Number Description Qty 1 ................ 78-8070-1395-4 .
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-84 Copyright 1999, 3M IPC. All rights reserved. Figure 7-33. Frame Assembly for Lower Head.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-85 Parts List Frame Assembly for Lower Head Item Part Number Number Description Qty 1 ................ 78-8070-1369-9 ............ FRAME, T ape Mount Lower Assembly .
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-86 Copyright 1999, 3M IPC. All rights reserved. Figure 7-34. Buffing Assembly for Lower Head.
3M-Matic 800rf Case Sealer Illustrated Parts Breakdown Copyright 1999, 3M IPC. All rights reserved. 7-87 Parts List Buffing Assembly for Lower Head Item Part Number Number Description Qty 1 ................ 78-8070-1391-3 ............ BUFFING ARM SUB ASSEMBL Y .
Illustrated Parts Breakdown 3M-Matic 800rf Case Sealer 7-88 Copyright 1999, 3M IPC. All rights reserved. This page intentionally left blank..
T able of Contents 8. Pr eventative Maintenance ............................................................................................................................ 8-1 8-1. General .............................................................
This page intentionally left blank. Pr eventative Maintenance 3M-Matic 800rf Case Sealer 8-ii Copyright 1999, 3M IPC. All rights reserved..
3M-Matic 800rf Case Sealer Preventative Maintenance Copyright 1999, 3M IPC. All rights reserved. 8-1 8. Preventative Maintenance 8-1. General The Model 800rf Case Sealer is designed for long, trouble-free service. 8-1-1. Maintenance The machine performs best when it receives routine maintenance and cleaning.
Pr eventative Maintenance 3M-Matic 800rf Case Sealer 8-2 Copyright 1999, 3M IPC. All rights reserved. 8-3. Lubrication Like most other equipment, the case sealer must be lubricated periodically to ensure long, trouble-free service. Most of the machine bearings are perma- nently lubricated and sealed and do not need further lubrication.
3M-Matic 800rf Case Sealer Preventative Maintenance Copyright 1999, 3M IPC. All rights reserved. 8-3 2. Side Belt Drive Assembly At 250 hours, use multipurpose grease. • Lightly coat chain pitches (Figure 7-13, # 75). 3. Column Assembly At 250 hours, use multipurpose grease.
Pr eventative Maintenance 3M-Matic 800rf Case Sealer 8-4 Copyright 1999, 3M IPC. All rights reserved. 8-4. Maintenance Schedule 1-1-1. T aping Heads The following table provides recommendations for inspecting and replacing parts, and cleaning and lubricating the upper and lower taping heads.
3M-Matic 800rf Case Sealer Preventative Maintenance Copyright 1999, 3M IPC. All rights reserved. 8-5 8-4-3. Main Assembly The following table provides recommendations for inspecting and replacing parts, and cleaning and lubricating the main assembly .
Pr eventative Maintenance 3M-Matic 800rf Case Sealer 8-6 Copyright 1999, 3M IPC. All rights reserved. This page intentionally left blank..
デバイス3M 39800の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
3M 39800をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこには3M 39800の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。3M 39800の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。3M 39800で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
3M 39800を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又は3M 39800の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、3M 39800に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわち3M 39800デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。