Curtisメーカー40の使用説明書/サービス説明書
ページ先へ移動 of 66
1740/-41/-42 Manual C URTIS I NSTRUMENTS, I NC. 200 Kisco Avenue Mt. Kisco, New Y ork 1 0509 USA T el. 9 1 4.666.297 1 Fax 9 1 4.666.2 1 88 www .cur tisinstruments.com © 2006 CUR TIS INSTR UMENTS, INC . 40 -series POWERCHAIR CONTROL SYSTEM 40-series Manual, p/n 37893 Rev.
.
Curtis enAble ® 40-Series Manual, Rev. B iii CONTENTS 1. O VER VIEW ..............................................................................1 Configurations .....................................................................2 P rofiles ....
iv Curtis enAble ® 40-Series Manual, Rev. B CONTENTS Sound & Display Parameters ............................................27 Reverse, Command, and Error Beep; Backlight Day/N ight Handcontrol Inhibit P arameters ................................
Curtis enAble ® 40-Series Manual, Rev. B v FIGURES FIG . 1: Curtis 40-Series P owerchair Control System ............................ 1 FIG . 2: M ounting dimensions, 1740 powerbase .................................. 5 FIG . 3: M ounting dimensions, 1741 user handcontrol .
.
1 Curtis enAble ® 40-Series Manual, Rev. B O VER VIEW The C ur tis enAble ® 40 P owerchair Control S ystem provides outstanding versatility packaged in an easy-to-install, easy-to-use set of three c.
2 Curtis enAble ® 40-Series Manual, Rev. B 1 — OVER VIEW ✔ Three flexible M ulti-Function input pins for advanced seat actuator inhibits, speed limiting, and swivel chair functions usually found only on high-end systems. ✔ P owerbase software is upgradable in the field or in the factory .
3 Curtis enAble ® 40-Series Manual, Rev. B 1 — OVER VIEW Profiles Each configuration in the 40-Series has two complete operational P rofiles, each with its own speed, acceleration, and other response parameters.
4 Curtis enAble ® 40-Series Manual, Rev. B Multi-Function Inputs The 40-Series introduces a level of seat and vehicle speed limiting/inhibit modes normally found on only the highest end Rehab systems.
5 Curtis enAble ® 40-Series Manual, Rev. B 2 — INST ALLA TION & WIRING 2 Fig. 2 Mounting dimensions, Curtis 1740 pow erbase. Dimensions in millimeters (and inches) INST ALLA TION AND WIRING INS.
6 Curtis enAble ® 40-Series Manual, Rev. B Mounting the 1741 Handcontrol Brass inser ts in the user handcontrol allow it to be securely mounted and re - mov ed/reinstalled many times. The handcontrol is designed to fit both tube and plate mounting systems.
7 Curtis enAble ® 40-Series Manual, Rev. B Mounting the 1742 Attendant Control Like the handcontrol, the attendant control has brass inserts that allow it to be securely mounted and remov ed/reinstalled many times. The field replaceable cable can be rotated to either of two positions, fore and aft.
8 Curtis enAble ® 40-Series Manual, Rev. B Fig. 5 Basic wiring diagr am, Curtis 1740 pow erbase. 2 — INST ALLA TION & WIRING PO WERB ASE WIRING Wiring for the 1740 powerbase is shown in F igure 5. The connections to the 14-pin connector ar e optional, depending on the level of functionality desired.
9 Curtis enAble ® 40-Series Manual, Rev. B 2 — INST ALLA TION & WIRING Fig. 6 Wiring for the M ulti-Function inputs. Molex High Current Contacts must be used for onboar d charging through this connector . Allowable current is 12 amps continuous.
10 Curtis enAble ® 40-Series Manual, Rev. B 1741 HANDCONTROL 1740 POWERBASE 1742 A TTEND ANT CONTROL 1740 POWERBASE 4 1 5 2 3 Pin 1 B+ Pin 2 B- Pin 3 Inhibit (active to ground/B-) Pin 4 TXD Pin 5 RXD.
11 Curtis enAble ® 40-Series Manual, Rev. B 3 USER HANDCONTROL (1741) The 40-S eries handcontrol is designed to be user-friendly . The keypad buttons are responsive and clearly marked. The LCD display is crisp and clear , with intuitive icons and backlighting to enhance daytime and nighttime readability .
12 Curtis enAble ® 40-Series Manual, Rev. B Drive Only (4-button keypad) The Drive Only keypad has four buttons: On/Off, Horn, Speed Up , and S peed Do wn. These four basic buttons are standard on all the keypad versions. On/Off Button The P ower On/Off button is located at the top of the keypad, abov e the display .
13 Curtis enAble ® 40-Series Manual, Rev. B Drive with Actuators (6-button keypad) This keypad’ s six buttons are the standard four (On/Off , Horn, Speed U p, S peed Down) plus two buttons to activate the two actuator modes. The mode buttons show one dot (for Mode 1) and two dots (for M ode 2).
14 Curtis enAble ® 40-Series Manual, Rev. B Drive with Actuators and Lights (8-button Keypad) This keypad’ s eight buttons are the standard four (On/Off , Horn, Speed U p, S peed Down) plus a Running Lights button, two buttons for the turn indica- tors (left and right), and an Actuator M ode button.
15 Curtis enAble ® 40-Series Manual, Rev. B Mode Button With the chair in Drive and the joystick in neutral, pressing the Mode button selects Mode 1 (actuator 1), and the appropriate portion of the chair icon lights up. Mo ving the joystick to the right selects Mode 2 (actuator 2); moving the joystick to the right again selects both modes.
16 Curtis enAble ® 40-Series Manual, Rev. B LCD DISPLA Y The LCD on the handcontrol briefly displays all of the system ’ s icons, as shown in F igure 9, during its self-test routine on startup.
17 Curtis enAble ® 40-Series Manual, Rev. B On/Off Button Mode Button Mode LED Battery LED Actuator LEDs (Seat Back) (Seat) (Left Leg) (Right Leg) Joystic k 4 — A TTENDANT CONTROL 4 A TTEND ANT CON.
18 Curtis enAble ® 40-Series Manual, Rev. B 4 — A TTENDANT CONTROL P ressing the M ode button longer than one second while the jo ystick is in neutral will select the Seat mode. The M ode LED will go dark, and the LED corresponding to Actuator 1 will be illuminated in the chair icon.
19 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS 5 PR OGRAMMABLE P ARAMETERS The enAble ® 40 P owerchair Control System has a number of parameters that can be programmed using a Curtis 1311 handheld programmer or Curtis 1314 PC P rogramming S tation.
20 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Configuration and MyChair Parameters The 174 0 po we rbas e ho lds fou r co mple te data set s co ntai ning val ues for all the pr ogr amm abl e pa ram ete rs.
21 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Drive Parameters (for Profiles 1&2) The Drive menu contains the major parameters that affect the for ward and reverse speed, response, and feel of the chair . There are separate Drive menus for P rofile 1 and Profile 2.
22 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Steer Parameters (for Profiles 1&2) The Steer menu contains the major parameters that affect the steering and turning response, speed, and feel of the chair . There are separate S teer menus for P rofile 1 and Profile 2.
23 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Steer Parameters (for Profiles 1&2) Fig. 12 Dynamic tur n r adius control, using the patent-pending Speed F ull T ur n and Speed N o T ur n par ameters. Fig. 11 Electronic gating, using the G ate Shape par ameter .
24 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Handcontrol Parameters The thr ee parameters in the Handcontr ols menu apply to the 1741 user hand- control and the 1742 attendant control.
25 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Speed Mode Parameters ☞ The Speed Mode menu allows the therapist, dealer , or OEM to set the number of modes that can be selected by the user and by the attendant, and the speed limit of each mode.
26 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Joystick Parameters JO YSTICK MENU P ARAMETER RANGE DESCRIPTION P erimeter Deadband 0–50 % Sets how close to the stop (gate) the joystic k must be moved before it is considered full on.
27 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Sound & Display and Charger Inhibit Parameters The parameters in the Handcontrol Inhibit menu allow the actuator func- tions to remain active (i.e., inhibit Off ) while the charger is plugged into the handcontrol.
28 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Seat Parameters The parameters in the Seat menu select which part of the seat each actuator controls, how fast it can move, and how end-stops are detected.
29 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Lights and Current Limits Parameters LIGHTS MENU P ARAMETER RANGE DESCRIPTION Running Lights On/Off Set to On if the v ehicle has running rights. Running Light V olts 12–24 V Defines the voltage for the running lights.
30 Curtis enAble ® 40-Series Manual, Rev. B The powerbase has three Multi-Function Inputs , which can be used to create a very flexible array of seat adjustment and drive speed limiting functions.
31 Curtis enAble ® 40-Series Manual, Rev. B Multi-Function Input 2 menu can be used to inhibit one or both actuators, and to set a corresponding speed limit.
32 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Multi-Function Input 3 Parameters Mul ti-F uncti on Inpu t 3 can be us ed to pr ov ide a swiv el cha ir fun cti on (=1 ). Al- ternatively , it can be used to provide an appropriate speed limit when a switch is activated (=2).
33 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Compensation Parameters COMPENSA TION MENU P ARAMETER RANGE DESCRIPTION High Speed Comp 0–100 % Sets motor load compensation at high speeds. Higher values provide stronger disturbance rejection, while smaller v alues provide smoother operation.
34 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Motors & Brakes Parameters MO T ORS & BRAKES MENU P ARAMETER RANGE DESCRIPTION A uto-T rim On/Off Enab les/disables the patented Auto-T rim f eature; see page 4.
35 Curtis enAble ® 40-Series Manual, Rev. B 5 — PROGRAMMABLE P ARAMETERS: Battery Parameters The Battery menu allows any lead acid battery to be installed and the BDI algorithm tailored to match it. Actual usage duty cycle greatly affects the settings and the o verall accuracy of the BDI algorithm.
36 Curtis enAble ® 40-Series Manual, Rev. B 6 6 — MONITOR MENU MONIT OR MENU Thr oug h its Mo nito r men u, th e 131 1 pro gram mer pro vid es ac cess to re al-t ime dat a dur ing chai r ope rati on.
37 Curtis enAble ® 40-Series Manual, Rev. B 6 — MONITOR MENU MONIT OR MENU , cont’ d ITEM DISPLA Y RANGE DESCRIPTION LIGHTS • • • Indicator Current 0–26.5 A Current through the indicator lights. Running Light Current 0–26.5 A Current through the r unning lights.
38 Curtis enAble ® 40-Series Manual, Rev. B 7 7 — TUNING GUIDE TUNING GUIDE This section sho ws you how to to zero in on the desir ed drive feel for the chair . The procedures should be conducted in the sequence given, because successive steps build upon the ones befor e.
39 Curtis enAble ® 40-Series Manual, Rev. B 7 — TUNING GUIDE 3 Set up the Speed Modes The chair can have up to nine different speed modes. The operator selects them by pressing the handcontrol’ s Up and Down buttons.
40 Curtis enAble ® 40-Series Manual, Rev. B STEP 7. F or no w , set the Hot System Resistance parameter at about 10% higher than System Resistance; this parameter will be adjusted later . STEP 8. Return to the Motor T est parameter (P rogram > Motor & Brakes menu) and turn it Off.
41 Curtis enAble ® 40-Series Manual, Rev. B 8 Set Up Compensation Setting the compensation parameters carefully will provide the proper control force during turning, caster reversal, and hill and curb climbing, and will also pro vide smooth and responsive acceleration and steering.
42 Curtis enAble ® 40-Series Manual, Rev. B STEP 9. N ext we wil l a djus t t he Fwd De cel, wh ich use s a n a dva nced al go- rit hm. F irst , set the S oft S top par ame ter to 10 %. a. S ele ct a s pee d mode t hat comm and s abou t 10–2 0% spee d.
43 Curtis enAble ® 40-Series Manual, Rev. B bl Set Up the T urn Accel/Decel Rates Adjusting the feel of the steering is one of the most critical steps in the tun- ing process.
44 Curtis enAble ® 40-Series Manual, Rev. B to incr eas e or decr eas e the spee d the cha ir driv es wh ile mak- ing a wid e turn . c. T o ad d Dyn amic T ur n Rad ius C ontr ol, first adju st th e S pee d Fu ll T urn par amet er .
45 Curtis enAble ® 40-Series Manual, Rev. B STEP 1. Drive the chair full speed and note how well it responds to small movements. Adjust the S teering Sensitivity v alue for more response. STEP 2. If th e ch air is stil l n ot r esp ons ive , y ou m ay n eed to rai se t he Hi gh S pee d Comp valu e set dur ing pro cedu re 8 .
46 Curtis enAble ® 40-Series Manual, Rev. B 7 — TUNING GUIDE set higher than the Low S peed Comp parameter , and can be set higher than 100%. Be careful, though, as too high settings can cause the chair to jerk and oscillate. If this happens, lower the Anti-Rollback Comp value.
47 Curtis enAble ® 40-Series Manual, Rev. B 8 8 — DIAGNOSTICS & TROUBLESHOOTING DIA GNOSTICS AND TROUBLESHOO TING The 40-series control system detects a wide variety of faults or error conditio.
48 Curtis enAble ® 40-Series Manual, Rev. B HANDCONTROL DIA GNOSTICS F aults are typically indicated by the wrench icon plus a flashing icon for the problem site. W arnings are indicated by the warning symbol instead of the wrench—or , in the case of keylock, by the key icon, and in the case of over/ undertemperature, by the thermometer icon.
49 Curtis enAble ® 40-Series Manual, Rev. B T able 1: HANDCONTROL INDICA T ORS, cont’ d HANDCONTROL LCD DISPLA Y F A UL T/W ARNING REMED Y Under v oltage W ar ning 1. Recharge batter y . 2. Replace old battery . 3. If this is happening frequently , replace charger.
50 Curtis enAble ® 40-Series Manual, Rev. B T able 1: HANDCONTROL INDICA T ORS, cont’ d HANDCONTROL LCD DISPLA Y F A UL T/W ARNING REMED Y Low battery . 1. Recharge battery . Lock ed mode. * 1. Unloc k the system. Chair under attendant control. * 1.
51 Curtis enAble ® 40-Series Manual, Rev. B A TTEND ANT CONTROL DIA GNOSTICS The LEDs on the attendant control are used to communicate information about faults, warnings, and batter y charging. The Mode LED, the BDI LED, and the LEDs in the chair icon signal warnings b y flashing.
52 Curtis enAble ® 40-Series Manual, Rev. B 9 MAINTENANCE The re are no user servic eabl e par ts in the Cu rtis 1740 cont rol ler . N o att empt sho uld be ma de to open , r epai r , or oth erwis e mod ify the cont rol ler . D oing so ma y dama ge the co ntr olle r and wil l voi d the war rant y .
Curtis enAble ® 40-Series Manual, Rev. B A-1 APPENDIX A: BDI SETUP APPENDIX A B A TTER Y DISCHARGE INDICA T OR (BDI) SETUP The B atter y D ischarge I ndicator on the enAble 40 system is quite flexible and, when properly set up , will provide the user with r eliable information on the status of the battery system.
A-2 Curtis enAble ® 40-Series Manual, Rev. B Step 3. Setting the Empty V oltage 3.a N ormally a value of 1.7 volts per cell is used as the empty point. This corresponds to a setting of 20.4 V . F or some sealed batteries, this may be too low . Consult the batter y manufacturer if you are unsure.
Curtis enAble ® 40-Series Manual, Rev. B A-3 formula: Charge Factor = 10 * (Batter y amp-hrs / Charger amps). 5.d S tar ting with the dead batter y from Step 4, plug in the charger . After 10 minutes of charging, measure the battery voltage with a meter .
A-4 Curtis enAble ® 40-Series Manual, Rev. B determine a new estimated battery charge level and then reset the BDI to the new estimate. U nfortunately , this estimate is wrong — because in fact no charge was actually put onto the batter y . 6.d The P arti al Cha rge M in par amet er is de sign ed pr ev ent th ese fa lse es tima tes .
Curtis enAble ® 40-Series Manual, Rev. B A-5 A-1 Fig. B-1 Curtis 1311 handheld progr ammer . APPENDIX B: 1311 PROGRAMMER APPENDIX B Curtis 1311 HANDHELD PROGRAMMER The C ur tis 1311 handheld programmer provides programming, diagnostic, and test capabilities for the enAble ® 40-Series P ower chair Contr ol S ystem.
A-6 Curtis enAble ® 40-Series Manual, Rev. B A-2 APPENDIX B: 1311 PROGRAMMER PROGRAMMER OPERA TION The 1311 programmer is easy to use, with self-explanatory functions. After plugging in the programmer , wait a few seconds for it to boot up and gather information from the controller .
Curtis enAble ® 40-Series Manual, Rev. B A-7 APPENDIX C: CONNECTORS & P ARTS LIST C-1 APPENDIX C MA TING CONNECT ORS & REPLA CEMENT P ARTS High Po wer Connectors, 1740 P owerbase Complete bat.
A-8 Curtis enAble ® 40-Series Manual, Rev. B APPENDIX D SPECIFICA TIONS APPENDIX D: SPECIFICA TIONS MODEL NUMBER OPTIONS 1742-20XX — D-1 T able D-1: 1740 PO WERBASE Nominal input voltage 24 V PWM operating frequency 15.
デバイスCurtis 40の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Curtis 40をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCurtis 40の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Curtis 40の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Curtis 40で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Curtis 40を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCurtis 40の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Curtis 40に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCurtis 40デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
