Datacom SystemsメーカーJ Classの使用説明書/サービス説明書
ページ先へ移動 of 273
J Class Owner ’ s Guide W orkstation Systems Group HP Part No. A4476–90013 Edition E0596 Printed in U.S.A..
Hewlett-Packard Co. 1995 First Printing: January 1995 Latest Printing: May 1996 UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. NOTICE The information contained in this document is subject to change without notice.
xiii Pr eface.
xiv This owner ’ s guide describes how to use your HP 9000 J Class work- station. This manual assumes that you have installed your workstation as described in the J Class Har dwar e Installation Guide.
xv This guide is intended for HP 9000 J Class workstation users. See Appendix A in the back of this manual for safety and regulatory statements that apply to this workstation.
xvi If you are using HP-UX version 10.0, refer to the following manuals for more information: • J Class Har dwar e Installation Guide (A4081–90600) • Using Y our HP W orkstation (A2615–90003) .
xvii Unless otherwise noted in the text, this guide uses the following sym- bolic conventions. literal values Bold words or characters in formats and command de- scriptions represent commands or key words that you must use literally . Pathnames are also in bold.
xviii If you have any questions, suggestions, or problems with our hard- ware, software, or documentation, please call 1–888–301–5932 ( US & Canada ) or contact the HP Response Center for your country .
iii Contents System Overview Product Description 1-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Unit Front Panel Controls, LED, and LCD 1-6 . . . . . . . . . . . . System LCD 1-7 . . . . . . . . . . . . . . . . . . .
iv IP Address and Subnetwork Mask Information 1-26 . . . . . . . . . . . Networking Overview 1-27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mail 1-27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v Using Y our DDS T ape Drive DDS T ape Drive and Data Cassette Descriptions 4-3 . . . . . . . . . . . . . . DDS Drive 4-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Controls and Indicators 4-3 . . . . . . . . . . .
vi Restoring Files from a Floppy Diskette to Y our System 5-9 . . . . . Listing the Files on a Floppy Diskette 5-10 . . . . . . . . . . . . . . . . . . For More Information 5-1 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring the Floppy Driver 5-12 .
vii CD-ROM Drive B-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DDS T ape Drive B-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Floppy Drive B-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
viii Displaying and Setting Paths D-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . Displaying and Setting the Monitor T ype D-14 . . . . . . . . . . . . . . . . . . The Monitor Command D-14 . . . . . . . . . . . . . . . . . . . . . . . . . .
ix 1–1. System Unit Front Panel Controls 1-6 . . . . . . . . . . . . . . . . . . . . 1–2. LCD Symbols 1-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3. System Unit with Removable Device Door Open 1-9 . . . . . . . .
x B–15. Fast, W ide Hard Drive Jumper Settings B-28 . . . . . . . . . . . . . . B–16. Replacing Hard Drive Mounting Bracket and Drive Orientation B-29 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B–17. Removing Storage Drawer from System Unit B-31 .
xi 1–1. Audio Electrical Specifications 1-14 . . . . . . . . . . . . . . . . . . . . . 1–2. Serial I/O Pins 1-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3. PS/2 Keyboard to ITF Keyboard Equivalent Keys 1-19 . . . . .
xii.
1-1 Chapter 1 System Overview • Product description • System unit front panel controls, LED, and LCD • System unit rear panel connectors • Monitors • Keyboards • Pointing devices • Opera.
1-2 This chapter introduces the HP 9000 J Class workstation. Its purpose is to familiarize you with your workstation and its controls and indi- cators. The instructions in this chapter assume you are using the HP-UX version 9.05 or later operating system with the HP VUE version 3.
1-3 This workstation has the following key features: • Operating System HP-UX version 9.05 or later • User Interface HP VUE version 3.0 graphical user interface • Compatibility Source and binary.
1-4 • Internal Storage Devices Fast, wide SCSI hard disk drives – up to two: 1.0 GB Drive 2.0 GB Drive Single-Ended SCSI removable Media – up to two: CD-ROM Drive 2.0–8.0 GB, 4-mm DDS tape drive Floppy drive • Standard Network Ethernet IEEE 802.
1-5 • EISA/GSC Five slots total; four EISA and three GSC that can be used as follows: two individual EISA, one individual GSC, and two combination EISA or GSC.
1-6 Before powering on your system, you should become familiar with the system unit controls. Figure 1–1 shows the the system unit front panel controls. Figur e 1–1.
1-7 System LCD The Liquid Crystal Display (LCD) is located on the left side of the front panel. It displays messages about the state of the system, includ- ing error codes.
1-8 If you are using HP-UX 9.05, the recommended method of shutting down your workstation is using the software command /etc/shut- down . If you are using HP-UX 10.0 or later , follow the instructions in Using Y our HP W orkstation to shut down your workstation.
1-9 Removable Device Bays (2) Figur e 1–3. System Unit with Removable Device Door Open.
1-10 This section describes the following connectors on the system unit’ s rear panel: • Audio connectors (including headphones and microphone) • PS/2 keyboard and mouse connectors • HP parallel Centronics I/O connector • 802.3 AUI LAN connector • 802.
1-1 1 TOC Button (not shown) Fast, Wide SCSIĆ3 Connector* SingledĆEnded SCSIĆ2 Connector* Keyboard Connector AUI LAN Connector T wisted P air Connector (labeled UTP) RSĆ.
1-12 The symbols shown to the left of the connector descriptions in the following text, such as the headphone and microphone for audio connectors, are the same symbols used on the rear panel of the J Class workstation.
1-13 • Audio Features Programmable sample rates: 8kHz, 16kHz, 32kHz, 48kHz, 1 1.025kHz, 22.05kHz, and 44.1kHz. Programmable output attenuation: 0 to –96dB in –1.
1-14 T able 1–1 summarizes the audio electrical specifications for this workstation. T able 1–1. Audio Electrical Specifications Frequency Response 25–20,000Hz Input Sensitivity/Impedance Line in 2.0Vpk/47kohm Microphone 22mVpk/1kohm Line Out 2.
1-15 ITF Keyboar d Connector The HP HIL connector provides an interface for the ITF keyboard to the system. Consult the documentation that accompanies each input device for specific information concerning its use.
1-16 T able 1–2. Serial I/O Pins Pin No. Signal 1 2 3 4 5 7 8 Request T o Send DCD RXD TXD DTR GND RT S CTS Description Data Carrier Detect Receive Data Data Set Ready Clear T o Send Data T erminal .
1-17 Y ou can use one of the following HP monitors with your workstation: • 17-inch, 1280x1024 color monitor (A4032A) • 17-inch, 1280x1024 color monitor (A4330A) • 20-inch, 1280x1024 color monit.
1-18 There are two types of Hewlett-Packard keyboards available for use with your workstation. They are the following: • PS/2 Keyboard • ITF Keyboard CAUTION: Use only devices that conform to the HP HIL specification with Hewlett-Packard computer systems.
1-19 T able 1–3. PS/2 Keyboar d to ITF Keyboard Equivalent Keys PS/2 Keycap Symbol ITF Keycap Symbol F9 blank1 (left) F10 blank2 F1 1 blank3 F12 blank4 (right) PrintScreen / SysReq Menu Scroll Lock .
1-20 T able 1–3. PS/2 Keyboar d to ITF Keyboard Equivalent Keys (Continued) PS/2 Keycap Symbol ITF Keycap Symbol Esc Esc / Del Insert Insert Char Home no equivalent Delete Delete Char Caps Lock Caps.
1-21 Y ou can use an HP three-button mouse, a trackball, or other options as pointing devices with your workstation by using the serial ports or the HIL port. For instructions on using your particular pointing de- vice, see the manual that came with it.
1-22 Y our workstation uses the HP-UX operating system, versions 9.05 and 10.0 or later . Instant Ignition systems, (systems with preloaded software), have X-windows and Hewlett-Packard’ s graphical user in- terface, HP VUE version 3.0, installed and configured.
1-23 Before you begin using your workstation, take a moment to gather the following important information and note it in the appropriate subsec- tion for future use: • LANIC ID • SCSI device ID .
1-24 T erminal Control A terminal window opens. 3. Move the mouse cursor into the terminal window and single- click the left mouse button. 4. If you are using HP-UX 9.05, enter the following at the prompt: /etc/lanscan Enter If you are using HP-UX 10.
1-25 SCSI ID and Device File Information for HP-UX 9.05 Default device file names for your drives are listed below . The under- lined number in the device file name indicates the SCSI ID number: Devic.
1-26 For installation on a system requiring short file names /dev/rmt/c#t#d#f0 A T&T style, best available density , character entry , rw–rw–rw /dev/rmt/c#t#d#f0b Berkeley style, best availabl.
1-27 Y our workstation is capable of many more tasks than are described in this owner ’ s guide. This section gives an overview of some of the net- working capabilities of your system and directs you to the appropriate source for more information. Mail Electronic mail allows you to send and receive mail messages on your workstation.
1-28 ftp ftp.
2-1 Chapter 2 Setting Up Y our Printer • Gathering printer information • Setting up a local printer using SAM • Setting up your printer for network printing • Printing a file • Solving print.
2-2 This chapter describes how to configure your workstation to use a printer that you have physically attached to either the parallel connec- tor or the serial (RS-232C) connector on the rear of your workstation. The instructions in this chapter assume you are using the HP-UX version 9.
2-3 Fill in the following list with the requested information and refer to it during the printer setup procedure: • Printer Interface (check one): Parallel Serial (RS232C) Port 1 Serial (RS232C) Port 2 • Printer Name: (The printer name is a name the system uses to identify the printer .
2-4 Follow the instructions in this section to set up a printer that is physi- cally attached to your workstation. The procedures in this chapter require you to log in as root . If you cannot log in as root , contact your system administrator . If your workstation is running HP VUE, follow these instructions to set up your printer using SAM.
2-5 4. A file manager window appears with a number of icons in it. Double-click on the System_Admin toolbox icon. 5. Move the mouse cursor to the SAM icon shown below (your icon can look like either of these) and double-click the left mouse button. 6.
2-6 9. Another menu opens. If your printer is connected to the parallel port on your workstation, click on Add P arallel Printer/Plotter . If your printer is connected to one of the serial connectors on your workstation, click on Add Serial (R S-232C) Printer/Plot- ter .
2-7 14. A window opens. Move the mouse cursor onto the scroll bar slider at the side of the new window . Press and hold the left mouse button while moving the mouse. When the model name of your printer appears, release the left mouse button. 15. Move the mouse cursor to your printer ’ s model name and click the left mouse button.
2-8 22. A window appears asking if your printer is powered on, has pa- per , is connected to your workstation, and is online. Check your printer to make sure it meets these requirements. Click on O K . 23. Click on O K at the bottom of the Messages window .
2-9 T erminal Control A terminal window opens. 29. Move the mouse cursor into the terminal window and click the left mouse button. 30. If you made your printer the default system printer , enter the fol- lowing command to test your printer: lp .
2-10 If you have a printer physically attached to your workstation, you can set it up to receive print requests from other computers on your net- work. T o do this, you must start up the remote line printer daemon. Follow the instructions in this section to set up your workstation to accept print requests from other computers on your network.
2-1 1 5. Save the file and close it. 6. Click on the T erminal Control on the Front Panel of your W orkspace. A terminal window opens. 7. Move the mouse cursor into the terminal window and click the left mouse button.
2-12 T o print a file, use one of the following command lines in a terminal window: lp filename Enter or lp –d printername filename Enter where filename is the name of the file that you want to print, and printername is the name of the printer on which you wish to print the file.
2-13 If you have printing problems,check the following: • Printer ’ s power cord is plugged in. • Printer is powered on. • Printer is online. • Printer has paper loaded. • Printer is set up for the correct interface type. • Printer cable is connected to the correct interface port on your printer .
3-1 Chapter 6 Using Y our CD-ROM Drive • CD-ROM drive and media descriptions • Loading and unloading a CD-ROM disc • V erifying the CD-ROM drive operation • Using device files • Mounting and.
3-2 This chapter provides an overview of the optional CD-ROM drive and media, and describes how to use the CD-ROM drive. W e assume the CD-ROM drive is set to the factory default address of SCSI ID 2. The instructions in this chapter assume you are using the HP-UX version 9.
3-3 This section describes basic information needed for using the CD- ROM drive and CD-ROM discs. CD-ROM Drive The CD-ROM drive is a random access read-only mass storage de- vice that uses removable CD-ROM discs. The drive supports the ISO 9660 and High Sierra format standards.
3-4 T able 6–1. CD-ROM Drive Operating Contr ols and Features Y ou can plug mini-headphones with a 3.5 mm diame- ter miniature stereo plug into this jack. Use the volume control to adjust the audio output vol- ume to the headphone jack. The Busy Indicator lights during a data access opera- tion and blinks during a data transfer .
3-5 CD-ROM Media CD-ROM discs are 120 mm (4.7 in.) in diameter , and use one data surface with a capacity of 600 megabytes. The data surface contains pits and flat spots arranged in a continuous spiral track, which is read at a constant speed.
3-6 This section describes how to perform tasks with your CD-ROM drive. Loading and Unloading a CD-ROM Disc This section describes how to load or unload a CD-ROM disc. Loading a CD-ROM Disc This CD-ROM drive has an automatic loading/ejecting feature. T o load a disc in the CD-ROM drive, follow these steps: 1.
3-7 2. Gently pull the disc tray fully open. 3. Hold the disc by the edges with the label side up and place it in the disc tray as shown in Figure 6–3. Figur e 6–3. Placing the CD-ROM Disc in the Disc T ray 4. Press down gently on the center of the CD-ROM disc to make sure it is seated on the disc tray hub, shown in Figure 6–3.
3-8 5. Gently push the disc tray in until it is closed, as shown in Figure 6–4. Figur e 6–4. Disc T ray Closed.
3-9 Unloading a CD-ROM Disc T o unload a disc from the Disc T ray , follow these steps: 1. Press and release the eject button on the CD-ROM drive. The disc tray opens approximately 1 inch, as shown in Figure 6–5. Figur e 6–5. CD-ROM Disc T ray Partway Open 2.
3-10 3. Grasp the disc by the edges and lift it out of the disc tray , as shown in Figure 6–6. Be careful to touch only the edges of the disc. Figur e 6–6.
3-1 1 4. Gently push the disc tray in until it is closed, as shown in Figure 6–7. Figur e 6–7. Disc T ray Closed V erifying the CD-ROM Drive Operation T o verify that your workstation can communicate with the CD-ROM drive, follow these steps: 1. Click on the T erminal Control on the Front Panel of your W orkspace.
3-12 T erminal Control A terminal window opens. 2. Move the mouse cursor into the terminal window and click the left mouse button. 3. If you are using HP-UX 9.05, enter the following at the prompt: /etc/ioscan –d scsi Enter After a few moments the ioscan utility lists all of the SCSI I/O devices it could find.
3-13 After a few moments the ioscan utility lists all of the SCSI I/O devices it could find. The list appears similar to the following: H/W Path Class Description ============================================ bc 8 bc I/O Adapter 8/0 ext_bus GSC built-in Fast/Wide SCSI Interface 8/0.
3-14 Using Device Files Device files are special files that tell your system which pathway to use through the system hardware when communicating with a specific device and what kind of device it is.
3-15 T o access information on a CD-ROM disc, you must first mount the disc. This applies to file system information only . If you wish to load a music CD, for example, you would not need to mount the disc.
3-16 3. Move the mouse pointer to the up arrow above the T oolbox control and click the left mouse button once. T oolbox Control Up Arrow 4. The T oolboxes subpanel opens. Click on the General toolbox icon, shown below . 5. A file manager window appears with a number of icons in it.
3-17 6. Move the mouse cursor to the SAM icon, shown below (your icon can look like either of these), and double-click the left mouse button. 7. The System Administration Manager window opens. Double- click on Peripheral Devices –>. 8. The Peripheral Devices window opens.
3-18 13. The Set Disk Usage and Options... window opens. Select File System and click on O K .. 14. The following screen messages appear: Task started. Creating the device file... Mounting file system... Modifying “/etc/checklist”... Task completed.
3-19 1. Log in as root . If you need information on logging in or setting up a user account, see Using Y our HP W orkstation . 2. Move the mouse pointer to the T oolbox control and click on the up arrow with the left mouse button. 3. The T oolbox subpanel opens.
3-20 6. The System Administration Manager window opens. Double- click on Peripheral Devices –>. 7. The Peripheral Devices window opens. Double-click on Disks and File Systems –>. 8. The Disks and File Systems window opens. Double-click on CD-ROM, Floppy , and Hard Disks.
3-21 Reading the Busy Light The CD-ROM busy light shows the status of the drive during the self test and during activity with the host system. The CD-ROM drive performs the self test when one of the following happens: • Y ou load a disc and close the Disc Tray .
3-22 T r oubleshooting If you have trouble with any of these procedures for using your CD- ROM drive, see Chapter 6 of this book, “Solving Problems.”.
4-1 Chapter 5 Using Y our DDS T ape Drive • DDS tape drive and data cassette descriptions • Setting the write-protect tab on a data cassette • Operating the DDS tape drive • Loading and unload.
4-2 This chapter describes how to perform tasks that archive to and trans- fer data from the optional DDS tape drive. It also describes how to maintain and care for the drive. W e assume the DDS tape drive is set to the factory default address of SCSI ID 3.
4-3 This section describes basic information needed for using your DDS tape drive and data cassettes. Depending on your configuration, your DDS drive may be a DDS-DC drive, or a DDS-2 drive.
4-4 LEDs – DDS-DC Drive This section describes the LED codes that are displayed. The front panel has two colored LEDs: the Cassette Light and the Drive Light. A green light indicates normal operation, and an amber light indicates a warning condition.
4-5 LED W arning Conditions – DDS-DC Drive The following sections describe actions to take if the LEDs indicate a warning condition. High Humidity If the LEDs display the high humidity signal, the humidity is too high and the drive does not perform any operations until the humidity drops.
4-6 4. If you are performing a backup from disk to tape, discard the data cassette and back up your files using a new data cassette. 5. If you are performing a restore from tape to disk, complete the restore, then discard the data cassette and back up the files to a new data cassette.
4-7 Data Cassettes Media Life HP DDS data cassettes are currently specified to 2000 passes over any part of the tape under optimal environmental conditions (50% relative humidity , 22 degrees C). During a tape operation, any one area of the tape may have multiple passes over the heads.
4-8 Media Restrictions If you interchange media between other HP workstation DDS tape drives, note that data cassettes with compressed data can only be read by tape drives that have data compression capabilities. This includes data cassettes that contain both compressed and noncompressed data.
4-9 This section describes how to perform tasks with your DDS tape drive. Loading and Unloading a Data Cassette Follow these steps to load and unload a data cassette in the DDS tape drive: 1. T urn on power to the tape drive. 2. Insert the data cassette into the drive, as shown in Figure 5–3.
4-10 3. Push the data cassette about three quarters of the way into the drive. The drive automatically pulls the data cassette the rest of the way in. When the LEDs on the front of the drive stop flash- ing, the drive has loaded the data cassette.
4-1 1 After a few moments the ioscan utility returns a message similar to the following: H/W Path Class Description ============================================ bc 8 bc I/O Adapter 8/12 ba Core I/O Adapter 8/12/5 ext_bus Built-in SCSI 8/12/5.3 target 8/12/5.
4-12 Using Device Files Y our system has four default device files for use with your tape drive: two device files for noncompressed mode and two device files for compressed mode. If you use these device files, you do not need to create any device files.
4-13 Device Files — Data Compression If you wish to use the data compression feature, use the device files /dev/rmt/3hc and /dev/rmt/3hcn , which are set for SCSI ID 3. If you use the /dev/rmt/3hc device file, the tape drive compresses the data and rewinds the data cassette every time the system releases the drive from its control.
4-14 Writing to a Data Cassette Use the following instructions to save files to a data cassette: 1. Check that the write-protect tab on the data cassette is in the write position. 2. Load the data cassette into the tape drive. 3. Click on the T erminal Control on the Front Panel of your W orkspace.
4-15 Restoring Files from a Data Cassette to Y our System Use the following instructions to restore files from a data cassette to your system: 1. Load the data cassette into the tape drive. 2. Use cd to change to the directory you want the files to reside in.
4-16 Listing the Files on a Data Cassette Use the following instructions to list the files on a data cassette: 1. Load the data cassette into the tape drive. 2. Click on the T erminal Control on the Front Panel of your W orkspace. A terminal window opens.
4-17 Further Command Information For additional information on using tar and a complete list of the command arguments, refer to the tar man page by typing the follow- ing: man tar Enter Y ou may also communicate with the tape drive with the cpio , ftio, mt , and fbackup commands.
4-18 Ordering Information T o order Hewlett-Packard data cassettes and cleaning cassettes for use in your DDS tape drive, use the following order numbers: • HP92283A Box of five 60–meter DDS data .
5-1 Chapter 5 Using Y our 3.5-Inch Floppy Disk Drive • Setting the write-protect tab on a diskette • Inserting and removing a diskette • V erifying the floppy disk drive configuration • Using .
5-2 This chapter describes how to perform tasks that allow you to archive to or transfer data from the optional 3.5-inch floppy disk drive. The instructions in this chapter assume you are using the HP-UX version 9.05 or later operating system with the HP VUE version 3.
5-3 This section describes basic information needed for using your floppy diskettes. Setting the Write-Protect T ab on a Diskette Y ou can only store or change information on a diskette when the write-protect tab is in the write position.
5-4 Inserting and Removing a Diskette Follow these steps to insert and remove a diskette from the floppy disk drive: 1. Insert the diskette into the drive, as shown in Figure 5–2. Eject Button Figur e 5–2. Inserting and Removing a Floppy Diskette 2.
5-5 This section describes how to perform tasks with your 3.5-inch floppy disk drive. V erifying the Floppy Drive Configuration T o verify that your workstation can communicate with the floppy drive, use the ioscan command in a terminal window to see which devices are currently in use on your system: 1.
5-6 After a few moments the ioscan utility lists all of the SCSI I/O devices it could find. If there is a SCSI floppy drive in the list, that listing appears similar to the following: H/W Path Description Status ============================== 2.0.1.0.
5-7 If the floppy driver is not configured, ioscan returns the follow- ing message: ioscan: Device driver scsifloppy is not in the kernel If you receive this message, go the the section, “Configuring the Floppy Driver” later in this chapter for information on adding the scsifloppy driver to the HP-UX kernel configuration.
5-8 Formatting a New Diskette Y ou must always format a new floppy diskette with the mediainit utility before using it. T o format a new floppy diskette follow these steps: 1. Log in as root . 2. Make sure that the write-protect tab on the floppy diskette is in the write position, as shown in Figure 5–1.
5-9 Saving Files to a Floppy Diskette Use the following instructions to save files to a floppy diskette: 1. Check that the write-protect tab on the floppy diskette is in the write position. 2. Load the formatted floppy diskette into the disk drive. 3.
5-10 A terminal window opens. 3. Move the mouse cursor into the terminal window and click the left mouse button. 4. Use the cd command to change to the directory you want the files to reside in: cd dir ectory_path Enter where dir ectory_path is the pathname of the directory .
5-1 1 4. Enter the following command line: tar –tvf /dev/rfloppy/c201d0s0 Enter All files on the floppy diskette are listed. For More Information For more information on using tar and a complete lis.
5-12 Configuring the Floppy Driver If you reload software or rebuild the Instant Ignition system on your workstation, you need to reconfigure the HP-UX Kernel to add the floppy driver . Use the SAM utility to add the SCSI flexible disk driv- er and build a new HP-UX kernel.
6-1 Chapter 5 Solving Pr oblems • Common problems and solutions • Dealing with a boot failure • Memory failures • LCD-indicated problems • Running system verification tests.
6-2 This chapter contains information to help you determine what’ s wrong with your system when you have problems. If you have a problem that isn’t listed in this chapter , or if your problem persists, contact your designated service representative.
6-3 The tables in this section list common problems you may encounter with your workstation. The tables also tell you what to do to help solve the problems. T able 5–1. Pr oblems Powering Up the System Problem Solution The power LED doesn’t light.
6-4 T able 5–2. Pr oblems Loading and Booting the Operating System Problem Solution The power LED is lit, and text appears on the screen, but more than two min- utes have passed with no sign of system activity . The system stops or hangs while booting.
6-5 T able 5–3. Pr oblems with the 802.3 Network Problem Solution Can’t reach other systems on the net- work. Applications that rely on the net- work won’t run. Check the network connector on the back of the system unit. Make sure that the network cable or transceiver is fastened securely to the connector .
6-6 T able 5–4. Pr oblems Using a Hard Disk Drive Problem Solution The disk drive is not accessible or does not respond. If problems persist, contact your system administrator or call your designated service representative. Make sure that all SCSI devices are set to the proper SCSI ID.
6-7 T able 5–5. Pr oblems Using the CD-ROM Drive Problem Solution The CD-ROM drive does not respond to commands. Re-enter the commands and make sure that you have typed them cor- rectly . Make sure that the system can com- municate with the drive as described in “Checking the SCSI IDs” in Appendix B.
6-8 T able 5–6. Pr oblems Using the DDS T ape Drive Problem Solution The DDS tape drive does not respond to commands. Re-enter the commands and make sure that you have typed them correctly . Make sure that you specified the cor- rect device file name for commands that require a device file name.
6-9 T able 5–7. Pr oblems Using the Floppy Disk Drive Problem Solution The floppy drive does not respond to commands. Re-enter the commands and make sure that you have typed them correctly . Make sure that you specified the de- vice file /dev/rfloppy/c201d0s0 for commands that require a device file name.
6-10 If your usual boot device (typically a disk) is not responding as it should, you must try to boot from the disk (or another boot device) by selecting it manually . T o boot a device manually , follow these steps: 1. Follow the directions in “Accessing the Boot Console Interface,” in Appendix D of this book.
6-1 1 J Class systems use Memory Page Deallocation, a feature that allows the system to provide information to the operating system about memory failures. HP-UX 10.0 uses Memory Page Deallocation information to map out the failing memory areas, and continue normal operation.
6-12 Y our workstation uses an LCD panel to display firmware/OS progress codes. The codes, referred to as chassis codes, consist of one of the mnemonics listed below , followed by a 4-digit hex number identify- ing the code module being executed.
6-13 The windows are as follows: Window 1 When the system is hard booted, the LCD will be cleared and the fol- lowing message will be displayed for approximately 1 second.
6-14 Window 5 When an attempt to boot is made, the following message is displayed once IPL is successfully loaded and launched: ZZZZ YYYY CPUXX ♥ <– line 1 – ’ ♥ ’ flashes with Z Y field change BBBBBBBBBBBBBBBB <– line 2 where BBBBBBBBBBBBBBBB is the model number (for example, 9000/J200).
6-15 HP-UX uses a diagnostics product called the Support T ools Manager that allows system operation verification. Y ou can access the Support T ools Manager in a terminal window . If you are using HP VUE as your interface, you can also access the Sup- port T ools Manager through the sys_admin directory .
6-16 A terminal window opens. 2. Move the mouse cursor into the terminal window and click the left mouse button. 3. Enter the following at the prompt: cstm Enter The following screen appears: Support Tool Manager Version A.01.00 Type ’help’ for a list of available commands.
6-17 6. T o exit the Support T ools Manager , type the following: CSTM> exit Enter If any tests failed, further diagnosis is necessary by qualified service personnel.
B-1 Appendix A Changing Y our W orkstation’ s Hardware Configuration • Checking the SCSI IDs • Opening the system unit • Closing the system unit • Installing removable media devices • Addi.
B-2 This appendix describes the procedures to change your workstation’ s hardware configuration. The instructions in this appendix assume you are using the HP-UX version 9.05 or later operating system with the HP VUE version 3.0 interface. CAUTION: Always wear a properly grounded wrist strap when reconfiguring your workstation.
B-3 T o determine which SCSI IDs are currently in use on your system, use the ioscan command in a terminal window: 1. Click on the T erminal Control on the Front Panel of your W orkspace. T erminal Control A terminal window opens. 2. Move the mouse cursor into the terminal window and single- click the left mouse button.
B-4 If you are using HP-UX 10.0 or later , enter the following at the prompt: /usr/sbin/ioscan –f Enter After a few moments the ioscan utility lists all of the SCSI I/O devices it could find.
B-5 4. If you are using HP-UX 9.05, you can determine which SCSI IDs are currently in use by looking under the H/W Path head- ing. The listing 2.0.1 scsi is the built-in SCSI bus controller . For devices connected to the built-in SCSI bus, such as disks, the fourth number is the SCSI ID for that device.
B-6 Perform the following steps to open the system unit: 1. Power off the system, the monitor , and any peripheral devices. Unplug the system unit power cord and the power cord of any peripheral devices from ac wall outlets. Refer to Using Y our HP W orkstation for the proper method of shutting down your work- station.
B-7 Figur e A–1. Removing the Fr ont Panel 4. Swing the panel down and pull up slightly so the two guide pins on the bottom clear their guides and lay the front cover down.
B-8 Perform the following steps to close the system unit: CAUTION: Do not attempt to operate the workstation with the front cover removed. The cover is needed for proper air flow for system cooling. 1. Insert the two guide pins on the bottom of the front cover into the guides on the bottom of the system unit.
B-9 Figur e A–2. Replacing the Fr ont Panel 3. Reconnect the power cables and any other cables that you dis- connected when opening the workstation, then power on any pe- ripherals, the monitor , and the system unit.
B-10 Y our workstation can have any two of the following removable media devices, with no two the same: • CD-ROM drive • 2 to 8 GB, 4 mm DDS tape drive • 3.5-inch Floppy disk drive Follow these steps for installing any of the removable media drives into the Storage Assembly .
B-1 1 Figur e A–3.
B-12 5. Set the drawer on a flat surface. 6. Unscrew the captive screw holding the EMI plate at the back of the removable drives and lift the plate up and out of the drawer , as shown in Figure A–4.
B-13 8. Unscrew the two screws holding the drive in the storage drawer , and slide the drive out of the drawer . See Figure A–5..
B-14 CD-ROM Drive The CD-ROM drive ships with the drive set to SCSI ID address 2. W e recommend keeping the address setting at 2 unless it is used by another device. CAUTION: CD-ROM drives are susceptible to mechanical and electrostatic shock. When handling the drive, always wear the static-grounding wrist strap that came in the CD-ROM drive kit.
B-15 ID 4 ID 2 ID 1 Jumpers 0 1 2 3 4 5 6 7 SCSI ID Address Address Address Address.
B-16 DDS T ape Drive The DDS tape drive ships with the drive set to SCSI ID address 3 and the Operation Mode switches set for correct drive opera- tion. W e recommend keeping the address setting at 3 unless it is used by another device. CAUTION: SCSI tape drives are susceptible to mechanical and electrostatic shock.
B-17 T arget ID Jumpers 0 1 2 3 Jumpers 4 5 6 T arget ID SCSI T erminators (must be removed) (Default) T erm PWR ID2 ID1 ID0 ID2 ID1 ID0 T erm PWR Figur e A–7.
B-18 SCSI ID 0 1 2 3 4 5 6 SCSI ID (Default) T erm PWR* Bit 2 Bit 1 Bit 0 Bit 2 Bit 1 Bit 0 T erm PWR* SCSI Connector Power Connector Bit 2 Bit1 Bit 0 T erm PWR *T erm PWR is not used in HP workstation configurations.
B-19 Operation Mode Switches ON 1 23 456 78 ON 12 3 4 5 6 7 8 Compression Disabled, No Host Control Compression Enabled, No Host Control Compression Disabled, Host Can Co.
B-20 Floppy Drive The floppy disk drive ships with the drive set to SCSI ID address 0. W e recommend keeping the address setting at 0 unless it is used by another device. CAUTION: Floppy disk drives are susceptible to mechanical and electrostatic shock.
B-21 SCSI ID Address Jumpers T op V iew of Floppy Disk Drive ID 0 ID 1 ID 2 Jumper in = 0; out = 1 SCSI ID Address Jumpers ID 0 ID 1 ID 2 Jumpers 0 1 2 3 4 5 6 7 SCSI ID Address Figur e A–10.
B-22 T op V iew of Floppy Disk Drive 1 2 3 SCSI T erminators Figur e A–1 1. Floppy Drive T erminators.
B-23 10. Figure A–12 shows the orientation of each of the removable me- dia drives in the bracket and the position of the screws holding the drive bracket in place.
B-24 11 . W ith the disk mounting bracket between the guides on each side of the Storage Assembly , slide the disk into the Storage Assem- bly , securing it with the two side screws. See Figure A–13. Do not over-tighten the side screws. Reconnect the drive SCSI and power cables here.
B-25 15. Push the drawer ejector handle up until the Storage Assembly slides all the way into the system unit and secure the two captive screws on the left of the Storage Assembly , as shown in Figure A–14. NOTICE: If the ejector handle is not pushed completely in, you may not have proper seating of the SCSI PCB interconnect to the backplane.
B-26 16. Follow the instructions in “Checking the SCSI IDs” earlier in this appendix, to verify that your workstation can see the newly installed drive. For information about using your drives see the following chapters in this book: • Using your CD-ROM drive is in Chapter 3.
B-27 This section describes how to add a hard drive to your workstation. The first part deals with installing a hard drive and the second part tells you how to configure your hard disk after it is installed. Y our workstation can have two hard drives.
B-28 6 5 4 3 2 1 0.
B-29 PCB Side of Drive T op Drive Bottom Drive Figur e A–16. Replacing Har d Drive Mounting Bracket and Drive Orientation.
B-30 Installing a Hard Disk Drive Perform the following steps to install a hard disk drive. NOTICE: Before opening the system unit, follow the instructions in “Checking the SCSI IDs,” earlier in this appendix, to determine the SCSI IDs currently in use on your workstation.
B-31.
B-32 5. Be sure you have already checked the SCSI ID of the drive you want to install using the method described at the beginning of this section. 6. W ith the disk mounting bracket between the guides on each side of the Storage Assembly , slide the disk into the Storage Assem- bly , securing it to the drawer with two side screws.
B-33 7. Reconnect the SCSI and power cables from the back of the drive to the side of the drawer assembly . 8. Slide the drawer back in and secure. 9. Close the system unit and reconnect all cables as described in the “Closing the System Unit” section in this appendix.
B-34 3. The T oolbox subpanel opens. Click on the General toolbox icon, shown below . 4. A file manager window appears with a number of icons in it. Double-click on the System_Admin toolbox icon. 5. Move the mouse cursor to the SAM icon shown below (your icon can look like either of these) and double-click the left mouse button.
B-35 The following screen message appears: Scanning the system’s hardware... The CD-ROM, Floppy , and Hard Disks window opens con- taining a list of drives currently configured on this system. 9. From the Actions menu, click on Add a Hard Disk Drive .
B-36 T ake a moment to read over the following important notes about installing memory: • Before trying to install additional memory SIMMs in your J Class workstation, use the procedure described in Appendix D, “The Boot Console Interface,” to determine the current memory configuration for this workstation.
B-37 Ejector T ab Ejector T ab Figur e A–19. Removing the CPU Assembly 4. Pull the CPU Assembly straight out and place on a flat surface with an antistatic mat. NOTICE: The CPU Assembly is heavy and has no safety catch. Be sure to pull it out slowly , making sure it is properly supported.
B-38 Memory SIMMs Figur e A–20. Memory SIMM Location 6. T o install a new memory SIMM, turn the CPU assembly until the memory SIMMs are in the position shown in Figure A–21.
B-39 Figur e A–21. CPU Assembly Orientation 7. Refer to the Position Guide on the CPU board that states, “<–– POSITION MEM MODULE AS SHOWN,” as shown in Figure A–21.
B-40 Any Combination of memory may be used, although, for maxi- mum performance, we recommend using common-sized memory SIMMs; either all 32 MB or 128 MB SIMM pairs. Therefore, to achieve both maximum performance and maximum future ca- pacity , use 128 MB SIMM pairs exclusively .
B-41 10. Place the SIMM in the connector , lining it up with the guides. Make sure to put the notched end toward the ejector handle (to the left). Gently press down on the ejector tabs to open them. Press SIMM down slightly . Push the SIMM firmly and evenly Ejector tabs pop partly back up.
B-42 12. Press firmly and evenly on the SIMM to ensure that it seats properly . 13. T o replace the CPU Assembly in the system unit, first align the top of the CPU Assembly with the guide on the system unit. Re- fer to Figure A–24 and to the label on the back of the assembly .
B-43 Next, align the bottom of the CPU Assembly with the guide on the system unit. W ith the ejector latches in the open position, slide the CPU Assembly into the system unit as far as it will go. See Figure A–24. 14. Press the ejector tabs all the way in and replace the two screws in the center of the CPU Assembly .
B-44 Perform the following steps to add a second processor to your workstation: 1. Open the system unit according to the directions in the “Opening the System Unit” section earlier in this appendix. 2. Remove the two screws in the center of the CPU Assembly .
B-45 4. Pull the CPU Assembly straight out and place on a flat surface with an antistatic mat. 5. Locate the CPU shroud as shown in Figure A–26..
B-46.
B-47 • Processors are shipped with a dust cover ( A ) over the connector . • There are two connectors on the CPU board for processors. If one of these connectors is not being used, it will have a dust cover ( B ) over the connector . T o remove these dust covers, follow the steps in Figure A–28.
B-48 9. Insert the board containing the processor module into the guides and press firmly into place. 10. Replace the CPU shroud over the processor and replace the six screws attaching the CPU shroud to the system board 11 . Reconnect the fan cable to the system board.
B-49 Next, align the bottom of the CPU Assembly with the guide on the system unit. W ith the ejector latches in the open position, slide the CPU Assembly into the system unit as far as it will go. See Figure A–29. 13. Press the ejector tabs all the way in and replace the two screws in the center of the CPU Assembly .
B-50 Y our workstation’ s EISA Assembly has five slots. Four are EISA slots; of these, two are EISA-only and two are EISA/GSC slots. The bottom slot is GSC only .
B-51 Figur e A–31.
B-52 Follow these steps to install an EISA or graphics board into your workstation: 1. W orking from the rear of the workstation, unscrew the four cap- tive screws and pull the EISA Assembly straight out using the handle. See Figure A–32. Figur e A–32.
B-53 2. Rotate the unit 90 degrees clockwise and place on a flat surface, as shown in Figure A–33..
B-54 3. Unscrew one screw at the back of the cover and lift the cover up and out to remove it from the EISA Assembly . See Figure A–34..
B-55 4. Unscrew one screw at the top of the slot cover and pull the cover straight up to remove it. See Figure A–35..
B-56 5. Place EISA or graphics board you are installing in the board guides and slide firmly into the connector . Check to see the board is evenly inserted to seat properly .
B-57 7. Insert cover in guide and secure with screw . Refer to Figure A–37. Figur e A–37. Replacing EISA Assembly Cover.
B-58 8. Rotate the unit back 90 degrees as shown in Figure A–38 and grasp the handle..
B-59 9. Slide the EISA Assembly into the system unit and secure it with the four captive screws. See Figure A–39. Figur e A–39. Replacing EISA Assembly.
B-60 Y our system ships from the factory preset to use a monitor with a spe- cific resolution and frequency . If you replace your monitor with a dif- ferent type, you must reconfigure your workstation.
A-1 Appendix B Safety and Regulatory Statements • Declaration of conformity • Emissions regulations • Emissions regulations compliance • Datacom users statement • Acoustics • Electrostatic.
A-2.
A-3 Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and the Canadian Department of Communications. These limits are de- signed to provide reasonable protection against harmful interference in a residential installation.
A-4 VCCI Class 1 ITE Any third-party I/O device installed in HP system(s) must be in ac- cordance with the requirements set forth in the preceding Emissions Regulations statements. In the event that a third-party noncompliant I/O device is installed, the customer assumes all responsibility and liability arising therefrom.
A-5 • Stand on a static-free mat. • W ear a static strap to ensure that any accumulated electrostatic charge is dischar ged from your body to ground. • Connect all equipment together , including the static-free mat, static strap, routing nodes, and peripheral units.
A-6 W ARNING: Removing device cover may expose sharp edges in equipment chassis. T o avoid injury , use care when installing customer add-on devices. W ARNUNG: Das Entfernen der Geräteabdeckung legt die scharfen Kanten im Inneren des Gerätes frei.
C-1 Appendix C SCSI Connections • SCSI bus differences • SCSI restrictions • Determining SCSI bus length • Assigning SCSI device IDs • Connecting to the SCSI ports.
C-2 This appendix provides information about connecting Small Comput- er System Interface (SCSI) devices to an HP 9000 J Class worksta- tion. The instructions in this chapter assume you are using the HP-UX version 9.05 or later operating system with the HP VUE version 3.
C-3 A Small Computer Systems Interface (SCSI) bus is an IEEE standard bus for connecting your workstation to internal and external devices (SCSI devices) running at different speeds, singly or in combination. Examples of these SCSI devices are floppy disk drives, 4-mm DDS- format tape drives, CD-ROM drives, and W inchester hard disk drives.
C-4 T able C–2. SCSI Bus Addr esses, ID Numbers, and Arbitration Priorities SCSI–2 Address Priority SCSI–2 ID Number 7 . . . . . . . . 1 . . . . . . . 1 6 . . . . . . . . . 1 . . . . . . 2 5 . . . . . . . . . . 1 . . . . . 3 4 . . . . . . . . . .
C-5 This section describes the SCSI restrictions that apply to your work- station in the following areas: • Cables • Connectors and terminator • SCSI configuration constraints Cables All SCSI devices ship without cables. Only SCSI cables approved by HP can be used to connect your workstation and any SCSI devices.
C-6 Singled-ended SCSI-2 definition limits the total cable length of SCSI-2 cables to 6 meters (19.6 feet). Fast, wide SCSI-3 definition limits the total cable length of SCSI-3 cables to 25 meters (82 feet). Always use the shortest possible cable(s) for your configuration.
C-7 Connectors and T erminator Any single-ended standard SCSI-2 device connecting to the system board must use a 50-pin high-density thumb screw connector on the end connecting to the system board, and a 50-pin low-density bail lock connector on the other end.
C-8 T able C–3. Single-Ended SCSI-2 Bus Configuration Constraints Single-Ended SCSI-2 Devices Maximum Number of Each T ype of Device Allowed Hard Disk Drives (internal and external) Floppy Disk Driv.
C-9 Fast, Wide SCSI-3 Bus Configuration Constraints Fast, wide SCSI-3 does not work with the single-ended standard SCSI-2. T able C–4 shows the configuration constraints for each fast, wide SCSI-3 device type.
C-10 2. In the fourth column, write down the lengths of the SCSI-2 interconnect cables you are using for your installation. (Cable lengths are listed in subsection “Cables” in the section on “SCSI Restrictions.”) 3. Add up all of the numbers in the third column and write that number on the subtotal line at the bottom of the column.
C-1 1 T able C–5. SCSI-2 Bus Length W orksheet for Single-Ended Standar d SCSI-2 Bus T otal SCSI-2 Bus Length = SCSI-2 Device Cable Length meters (feet) meters (feet) System Unit 7980S A1999A 0.3 (1.0) C1701C C1704C Internal SCSI-2 Bus Length + Device Internal Length Subtotals: meters (feet) External C1520A C1521A C1700C C1705C C2213A 0.
C-12 Fast, Wide SCSI-3 Bus Length Follow these instructions to calculate your total fast, wide SCSI-3 bus length for the fast, wide SCSI-3 bus on your system using T able C–6: 1. List all of your internal SCSI-3 devices in the first column. 2. In the second column, write the lengths of the internal SCSI-3 bus that correspond to your devices.
C-13 T able C–6. SCSI-3 Bus Length W orksheet for Fast, W ide SCSI-3 Bus T otal SCSI-3 Bus Length = SCSI-3 Device Internal SCSI-3 Bus Length meters (feet) C3034T C3035T C3036T meters (feet) Device I.
C-14 Before assigning a SCSI device ID to your drive, you need to check your existing SCSI device IDs. T o determine which SCSI device IDs are available for your device, use the ioscan command in a terminal window: 1. Click on the T erminal Control on the Front Panel of your W orkspace.
C-15 If you are using HP-UX 10.0 or later , enter the following at the prompt: /usr/sbin/ioscan –f Enter After a few moments the ioscan utility lists all of the SCSI I/O devices it could find.
C-16 4. If you are using HP-UX 9.05, you can determine which SCSI IDs are currently in use by looking under the H/W Path head- ing. The listing 2.0.1 scsi is the built-in SCSI bus controller . For devices connected to the built-in SCSI bus, such as disks, the fourth number is the SCSI ID for that device.
C-17 4. Check to see which SCSI device IDs are not used. Y ou can use ID numbers 0 through 6 if they are not already in use. If the de- fault ID on your drive does not conflict with any existing drive IDs, use that ID. If your default address conflicts with an exist- ing drive ID, you need to assign a new SCSI device ID to your drive.
C-18 T able C–7. Single-Ended SCSI Device IDs SCSI Device Drives Device ID (Address) Number (Only 0 through 6 A vailable) Internal External System SCSI Drive(s) Floppy Disk Drive (if present, uses ID No. 0) N/A N/A CD–ROM Drive (if present, uses ID No.
C-19 6. W rite in the type of external single-ended drives currently con- nected to your workstation under the heading “External Device Drives” and each drive’ s SCSI device ID under the heading “De- vice ID Number .” 7. Add your new drive to the table if it is an external device.
C-20 Fast, Wide SCSI IDs Before assigning a SCSI device ID to your drive, you need to check your SCSI device IDs. T o check which SCSI device IDs are available and assign an ID to your device, follow these instructions which use T able C–8: 1.
C-21 This section describes how to connect to the system SCSI ports (single-ended and fast,wide). System SCSI Port Connection The system contains two (2) SCSI connectors: • System Single-Ended SCSI-2 Connector • System Fast, W ide SCSI-3 Connector Figure C–1 shows the rear panel with terminators attached to the two SCSI connectors.
C-22 Figur e C–1. Rear Panel SCSI Connectors with T erminators Attached.
C-23.
D-1 Appendix D The Boot Console Interface • Boot console interface features • Accessing the boot console interface • Booting your workstation • Searching for bootable media • Resetting your .
D-2 This appendix describes the different features of the boot console in- terface and how to use them. The instructions in this chapter assume you are using the HP-UX ver- sion 9.
D-3 There are times when you want to interact directly with the hardware of your workstation before it boots the operating system. Y our work- station provides a menu-driven boot console interface that allows you to perform special tasks, display information, and set certain sys- tem parameters, even if the operating system is unavailable.
D-4 The boot console menus follow , showing the various tasks you can perform and the information available. The shortened version of all commands is indicated by the uppercase letters. Help is available for all the menus and commands by using either help , he , or ? and the menu or command you want help on.
D-5 –––––– Configuration Menu ––––––––––––––––––––––––––––––––––––––––––––––––––––.
D-6 –––––– Information Menu –––––––––––––––––––––––––––––––––––––––––––––––––––––.
D-7 –––––– Service Menu ––––––––––––––––––––––––––––––––––––––––––––––––––––––.
D-8 T o access the boot console interface, follow these steps: NOTICE: This procedure should be done by a system ad- ministrator . 1. Close any files and applications on your workstation. 2. Follow your normal shutdown procedure. For more information on shutting down your workstation, see Using your HP W orksta - tion .
D-9 Usually , you start your workstation by turning it on and waiting for HP-UX to boot automatically . However , you may not always want the usual sequence to occur . For example, you may want to start your workstation from an operat- ing system that is stored on a device that is different from your usual boot device.
D-10 • If you wish to interact with the Initial System Loader ( ISL ) before booting your workstation, follow the directions in “Accessing the Boot Console Interface” earlier in this appen- dix,.
D-1 1 T o list devices that contain bootable media, follow the directions in “Accessing the Boot Console Interface” earlier in this appendix, and then type the following at the prompt: Main Menu: Enter a command or a menu > search ipl Enter The search command searches all buses.
D-12 T o reset your workstation, follow the directions in “Accessing the Boot Console Interface” earlier in this appendix, and then type the following at the prompt: Main Menu: Enter a command or a menu > reset Enter A path is the hardware address of a device that is attached to the I/O system of your workstation.
D-13 T able D–2. Mnemonic Style Notation I/O T ype Built-in FWSCSI Built-in SCSI Built-in LAN Specification Format fwscsi . scsi_addr ess.logical_unit_number scsi .
D-14 Y our system ships from the factory preset to use a monitor with a spe- cific resolution and frequency . If you replace your workstation’ s mon- itor with a different type of monitor , you must reconfigure your workstation to support the new monitor .
D-15 only card in the system and be physically located in slot 0. The monitor command lets you change your workstation’ s graphics configuration befor e you replace your monitor . For information about changing the configuration after you replace your monitor , go to the section “Changing Y our Monitor T ype” in Appendix B of this book.
D-16 Setting the Monitor T ype Using the list in the example above, you can set the monitor type for graphics slot 0 by typing the following: Configuration Menu: Enter command > monitor graphics0 Enter NOTICE: Y ou can exit at this point by entering x , and the monitor type will not be changed.
D-17 The MONITOR INFORMATION table reappears with the new moni- tor shown in slot 0. Slot # HPA State Resolution Frequency Class ––––––––– –––––––––– ––––.
D-18 T rying to change the monitor type on an empty slot, gives you this warning message: Configuration Menu: Enter command > monitor graphics2 Enter MONITOR INFORMATION WARNING: Intended graphics hardware does not exist. Be sure to install the hardware after you power down the system.
D-19 The following sample screen output using the memory command shows first, a memory configuration table with properly-installed and configured memory (Sample Output 1); and second, output when a SIMM has been improperly installed (Sample Output 2).
D-20 Active, Installed Memory (bytes) : 201326592 of Standard DRAM’s Deallocated Pages (bytes) – 0 ––––––––– Available Memory (bytes) : 201326592 Good Memory Required by OS (byte.
D-21 BAD MEMORY TABLE SMC SMC Status Bank Bank Status SIMM Size Slot/Sys Brd ––– –––––––––– –––– –––––––––––– ––––––––– –.
D-22 The eisa command lets you identify all EISA cards currently installed on your workstation by showing you the current status of your workstation’ s four EISA slots.
D-23 auto boot and auto search are variables stored in your workstation’ s non-volatile memory . (Non-volatile memory retains its contents even after power is turned off.) If you reset these flags to new value, the change takes effect the next time you reboot the workstation.
D-24 When fastboot is enabled (set to on ), your workstation does a quick check of the memory and skips I/O interface testing during its power- on self tests. This enables your workstation to complete its boot pro- cess quicker . The default factory setting is for fastboot to be enabled ( on ).
D-25 The LAN station address is displayed as a twelve-digit number in hexadecimal notation, similar to the following: LAN Station Addresses: 123456–789abc The address is for the system’ s built-in LAN.
GL-1 Glossary absolute pathname The full pathname of a file, including all the directories leading to it, starting with the root directory (“/”) and ending with the filename it- self. See also file , filename , pathname . access permissions Settings that allow a user or group of users to read, write, or execute files.
GL-2 attachment unit interface (AUI) A transceiver cable that conforms to IEEE 802.3 specifications. back up v . T o make a copy of the file system on a tape or disk that can be stored separately from the original files. Also called “backing up the system” or simply “system backup.
GL-3 bootstrap service See boot . byte A fundamental character–code unit, usually consisting of 8 bits. CD–ROM Compact Disc Read–Only Memory . See also CD–ROM disc , CD– ROM drive . CD–ROM disc CD–ROM discs are identical to the audio compact discs (CDs) used to record stereo music, except that they store data.
GL-4 click T o press and r elease a mouse button. The term comes from the fact that pressing and releasing most mouse buttons makes a clicking sound. cluster A group of workstations connected via a Local Area Network (LAN). One workstation, the cluster server , performs as a file–system server for the cluster clients.
GL-5 command argument Information you provide on a command line to describe the object (usually a file or directory) to be operated on by the command. command interpreter A program that reads lines of text from standard input (typed at the keyboard or read from a file) and interprets them as requests to execute other programs.
GL-6 current dir ectory See current working dir ectory . current session The work and processes that have been created since you logged into the system (and before you log out again). See also session . current working dir ectory The directory in which a relative path name search begins, as well as the directory in which you are currently working.
GL-7 dialog box A special type of HP VUE screen that is called by the user from a window . Dialog boxes contain controls and settings. T o display an example of a dialog box, click the Style Manager button on the W ork- space, then click on Color .
GL-8 diskless workstation A workstation that has no disk. A diskless workstation can use the disk of its partner workstation or other workstations. If necessary , it can also use the computational services of the partner workstation or other workstations.
GL-9 environment variables The set of defined shell variables (some of which are P A TH, TERM, SHELL, EXINIT , HOME) that define the conditions under which your commands are executed. These conditions include your worksta- tion characteristics, home directory , and default search paths.
GL-10 File Manager The HP VUE application that allows you to manage your files and directories, and to set viewing preferences. filename The name given to a particular file. See also absolute pathname , file , pathname . file server A workstation whose primary task is to control the storage and re- trieval of data from hard disks.
GL-1 1 hard disk drive A device that stores data on a hard disk. The hard disk is a permanent part of the drive and cannot be removed. HCRX color graphics Accelerated 8–plane or 24–plane graphics. See also CRX color graphics . Help Manager The HP VUE application that provides online help.
GL-12 HP V isual User Environment A user interface that draws a graphical layer over the complexities of the other layers of the system (the hardware, operating system, and X W indow system), enabling you to control your workstation by direct- ly manipulating graphical objects instead of by typing commands at a command–line prompt.
GL-13 input window The window that displays a program’ s prompt and any commands typed but not yet executed. internet protocol addr ess (IP address) A string of characters that uniquely identifies a workstation in a net- work. Also referred to as the IP address, the system name, and the host name.
GL-14 LAN station address See local area network station addr ess . link n. A special object that contains the name of another object. When you specify a link as a pathname or part of a pathname, the system substitutes the pathname that the link contains.
GL-15 login script The shell program that runs at each login, and sets the login environ- ment for your system. menu bar An area at the top or bottom of a window that contain the titles of the pull–down or pop–up menus for that application. minimize button In HP VUE, a push button on the window frame that turns a screen into an icon.
GL-16 node A network computer (workstation). Each node in the network can use the data, programs, and devices of other network nodes. Each node contains main memory and has its own disk or shares one with anoth- er node. See also disked workstation , diskless workstation , workstation .
GL-17 output window The window that displays a process response to your command. parent dir ectory A directory that contains other directories, each of which is then called a subdirectory . See also subdirectory . partner node A workstation that shares its disk with a diskless node.
GL-18 PID Process Identification. Also referred to as a process ID. See also pro- cess ID . pointer Sometimes called the “mouse pointer ,” the pointer shows the mouse location on the screen. The pointer ’ s shape depends on its location. In the HP VUE W orkspace, the pointer is an X.
GL-19 RAM Random access memory . ROM Read–only memory . root See superuser . scr oll bar A vertical or horizontal bar located on the side or bottom of a window that allows the user to view information that does not fit within the window . SCSI See Small Computer System Interface .
GL-20 shell command An instruction you give the system to execute a utility program or shell script. See also shell script , utility program . shell script A file that contains commands that the system can interpret and run in a shell. shutdown The process of taking the system from multi–user state to system ad- ministration state.
GL-21 standalone A workstation that is not part of a cluster . See also cluster . Style Manager The HP VUE application that provides the ability to customize vari- ous aspects of your system, including colors, fonts, the keyboard, the mouse, session startup and termination behavior , and access to other workstations.
GL-22 system name See internet protocol addr ess . terminal window A terminal window is a type of HP VUE window that emulates a complete display terminal. T erminal windows are typically used to fool non–client programs into believing they are running in their fa- vorite terminal.
GL-23 username The name that the system recognizes as uniquely yours. Also known as your login name. The username is also the name that identifies you to the mail system and other software requiring secure entry .
GL-24 W orkspace Manager The program that controls the size, placement, and operation of win- dows on the HP VUE W orkspace. The W orkspace Manager is a spe- cial W indow Manager . See also W indow Manager . workstation A compact, graphics–oriented computer having high speed and high memory capacity .
Index-1 Index A 0 %+ "!/0-!. 4 .,!%"%/%+*. 4 0 %+ +**!/+-. $! ,$+*!. 4 )%-+,$+*! .
Index-2 commands auto , D Ć23 auto boot , D Ć23 auto search , D Ć23 boot , D Ć9 cpio , 4Ć17, 5Ć11 cstm , 6Ć15 eisa , D Ć22 exit , 6Ć17 fastboot , D Ć24 fb.
Index-3 '*$)" ) /)'*$)" . -- .. 343 ( $ $). ,#)" $'$.2 , -.,$.$*)- 3 3 ( $ '$! 343 *0 ,0$ 1 343 .
Index-4 H hard drive adding, B Ć33ćB Ć35 attaching mounting bracket, B Ć29 configuring, B Ć33 installing in system unit, B Ć30ćB Ć33 jumper settings, B Ć28 hardware configuration.
Index-5 ##%(. )'+$ / #$#%$ )*." $%** %$ / #%$ *%( $ $ *.& %%* %$)%" $*( / %##$ / )&".
Index-6 R '%%& 0 )%'+$/ '(/!& !$* '%%& )%'-$ .
Index-7 )&#,!% '(&#$) / &&* !#+( / !%!* . * /0/ $$&(.
デバイスDatacom Systems J Classの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Datacom Systems J Classをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDatacom Systems J Classの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Datacom Systems J Classの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Datacom Systems J Classで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Datacom Systems J Classを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDatacom Systems J Classの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Datacom Systems J Classに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDatacom Systems J Classデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
