dbx Proメーカー162SLの使用説明書/サービス説明書
ページ先へ移動 of 31
User Manual Compressor/Limiter ® 16 2SL.
W ARNING FOR YOUR PROTECTION READ THE FOLLOWING: KEEP THESE INSTRUCTIONS HEED ALL W ARNINGS FOLLOW ALL INSTRUCTIONS DO NOT USE THIS APP ARA TUS NEAR W A TER CLEAN ONL Y WITH A DR Y CLOTH. DO NOT BLOCK ANY OF THE VENTILA TION OPENINGS. INST ALL IN ACCORDANCE WITH THE MANUF ACTURER’S INSTRUCTIONS.
U.K. MAINS PLUG W ARNING A molded mains plug that has been cut off from the cord is unsafe. Discard the mains plug at a suitable disposal facility . NEVER UNDER ANY CIRCUMST ANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG INTO A 13 AMP POWER SOCKET .
Intr oduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Why you need compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 The difference between compressors and limiters .
Wh y Y ou Need A Compr essor A remarkable feature of the human ear is that it can detect an extremely wide range of amplitude changes - from the slightest whisper to a deafening clap of thunder .
The Differ ence Between Compr essors and Limiters By measuring the dynamic range of musical instruments in live recording situations, you will experience extreme amplitudes which will often lead to overload in subsequent signal processing equipment. Especially in broadcasting and digital recording, these signal peaks can lead to heavy distortion.
The Compr ession and Limiting Effects On a compressor , there is a relationship between the input signal, and the threshold level, input, out- put, and ratio settings. Look at an input signal applied to the inputs of two compressors. The threshold level of the second unit is set ten decibels higher than the threshold of the first unit.
6 Furthermore, it is interesting to note that by comparing the input and output wavefor ms for the com- pressed mode, the quietest sections of the input signal have been effectively raised in level, where- as the loudest sections have been effectively decreased in level.
7 GAIN control. If the output gain is set too high as compared to the PeakStopPlus Level control, con- tinuous limiting can occur . While PeakStopPlus is typically used as a protective function, creative effects can be achieved by intentionally driving the signal into heavy PeakStopPlus limiting.
.
9 The 162SL is connected for operation using the rear panel XLR or 1/4” connectors. Note that the two rear panel input sections have a push-switch which lifts the contact on pin #1 (ground). Keep this switch in the OFF position (pin #1 connected) until all connections are made.
10 OverEasy ® Switch : This switch activates/deactivates the OverEasy ® characteristics of the 162SL. When the switch is IN, the 162SL is in O VER E ASY mode. OverEasy is a process which allows the user to compress a signal more gently than a hard knee compressor through the threshold region.
increase in output level, regardless of how far the set threshold level is exceeded. This occurs in both OverEasy® and hard knee operation. Note that when a compressor is set to a compression ratio of 10:1 or more, it may be considered to be LIMITING the input signal, especially when a fast attack time is selected.
Pe a kStopPlus ® Switch and LED : The dynamics of the dbx 162SL are set to handle fast transients through PeakStop ® limiting and the newer PeakStopPlus. PeakStop is the process first introduced on the dbx 165A compressor/limiter . PeakStop is made up of an extremely fast-reacting detector , called Instantaneous T ransient Clamp.
By pass Switch and LED : This switch activates a hard-wire relay bypass system, which allows the audio signal to pass through the compressor directly from input to output, even when the 162SL is turned of f.
Note that the gain reduction scale is linear in dB as opposed to the standard VU markings on the upper scale on which input and output levels are monitored. This allows for easy visual indication of gain reduction, as it can be read in a fraction of a second, with only a fleeting glance from the engineer .
15 Au d io Input and Output Connectors: Each audio input and output channel of the 162SL offers both 1/4” and XLR connectors. The connectors are default wired in balanced mode (pin 2 /tip hot), although supplying an unbalanced signal presents no difficulty to the 162SL.
.
In a typical hard-knee compressor , the threshold control sets a reference level above which input sig- nals will be attenuated in the manner defined by the setting of the Compression ratio control. Input sig- nals which fall below this level will pass through unprocessed.
T wo channels of program material do not necessarily constitute a stereo program. A stereo program is one where the two channels are recorded and/or mixed to create the illusion of a single unified panora- ma of sound.
trols. This faster attack time allows the transients to by captured and compressed without overshoot and allows a quick release from compression without “punching holes” in the sound.
While PeakStopPlus™ is typically used as a protective function, creative effects can be achieved by inten- tionally driving the signal into heavy PeakStopPlus™ limiting. Great care has gone into the design of the PeakStopPlus™ limiter to keep it acoustically transparent.
tions. V ocalists and musicians don't get the sense of being held back, but high average levels can be maintained without speaker damage due to excessive heat buildup.
not cause compression, and the program is not subject to the phase shift normally caused by program equalization. During the recording of cymbals and tom-toms, a compressor with an equalizer in the sidechain path can help prevent tape saturation.
Anticipated Compression By feeding the program directly to the 162SL's sidechain return and sending the audio signal through a delay line before the audio input, the unit can anticipate the need for a gain change. See diagram on the following page.
.
If you require technical support, contact dbx Customer Service. Be prepared to accurately describe the problem. Know the serial number of your unit - this is printed on a sticker attached to the rear panel. If you have not already taken the time to fill out your warranty registration card and send it in, please do so now.
26.
INPUTS Connectors: Female XLR and 1/4” TRS (Pin 2 and Tip hot) T ype: Electronically balanced/unbalanced, RF filtered. Impedance: Balanced > 50 k Ω , unbalanced > 25 k Ω .
FUNCTION SWITCHES Sidechain: Routes external sidechain input signal to the detector . OverEasy ® : Activates the OverEasy‚ compression function. Auto: Activates automatic program-dependent attack and release times, disabling the manual attack and release controls.
® 8760 South Sandy Pkwy . Sandy , Utah 84070 Phone: (801) 568-7660 F ax: (801) 568-7662 Questions or comments? E•mail us at: customer@dbxpr o .com or visit our W orld Wide W eb home pag e at: www .
デバイスdbx Pro 162SLの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
dbx Pro 162SLをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはdbx Pro 162SLの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。dbx Pro 162SLの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。dbx Pro 162SLで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
dbx Pro 162SLを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はdbx Pro 162SLの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、dbx Pro 162SLに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちdbx Pro 162SLデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
