DellメーカーE08J001の使用説明書/サービス説明書
ページ先へ移動 of 10
Dell PowerVault MD3060e Storage Enclosure Getting Started Guide Regulatory Model: E08J Series Regulatory Type: E08J001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Installation And Configuration CAUTION: Before performing the following procedure, review the safety instructions that came with the system. Unpacking A Rack System WARNING: The weight of your system without the physical disks installed (empty weight) is 19.
Opening And Closing The Disk Drawer Figure 2. Opening and Closing the Disk Drawer Open the disk drawer to install or remove the physical disk carrier(s). NOTE: You can open only one disk drawer at a time. Forcing to open more than one drawer at a time may damage the assembly or produce unexpected results.
Connecting The Power Cable(s) Figure 4. Connecting the Power Cable(s) Connect the system’s power cable(s) to the system. Securing The Power Cable(s) Figure 5. Securing the Power Cable(s) Open the cable retention bracket by pulling the tabs on its sides, insert the cable, and secure the system power cable, as shown in the illustration.
Turning On The System Figure 6. Turning on the System Turn the power switch on the back of the system to the On position. The power LED will turn on. Installing The Bezel Figure 7.
• As a storage enclosure when connected to a Dell PowerEdge server via a Dell qualified Host Bus Adapter (HBA). • When using the MD3060e as a storage enclosure, attached to Dell PowerEdge Server(s.
Power NOTE: This system is also designed to be connected to IT power systems with a phase to phase voltage not exceeding 230 V. Battery 6.6 V DC, 1100 mAh, 7.26 W Lithium Ion Battery Physical Height 177.80 mm (7.0 inch) Width 482.60 mm (19.0 inch) with rack latches Depth 825.
Environmental Operating One shock pulse in the positive z axis (one pulse on each side of the system) of 31 G for 2.6 m in the operational orientation. Storage Six consecutively executed shock pulses in the positive and negative x, y, and z axes (one pulse on each side of the system) of 71 G for up to 2 m.
Environmental NOTE: Applies to data center and non-data center environments. Gaseous Contamination NOTE: Maximum corrosive contaminant levels measured at ≤50% relative humidity Copper Coupon Corrosion Rate <300 Å/month per Class G1 as defined by ANSI/ ISA71.
デバイスDell E08J001の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dell E08J001をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDell E08J001の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dell E08J001の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dell E08J001で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dell E08J001を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDell E08J001の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dell E08J001に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDell E08J001デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。