Deltaメーカー36-953の使用説明書/サービス説明書
ページ先へ移動 of 32
INSTRUCTION MANUAL P ART NO. 422-40-651-0013 - 01-24-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury .
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL WARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage.
5 ADDITIONAL SAFETY RULES FOR T ABLE SA WS 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this machine.
6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
7 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
Fig. 1 1. Unisaw 2. Switch (shown with a GPE switch) Fig. 2 3. Extension wing 4. Handwheel 5. Blade guar d and splitter assembly 6. Upper bracket for splitter 7. Lower bracket for support r od 8. Support r od 9. 7/8" Open end arbor wr ench 10. 7/8"x1/2" Closed end arbor wrench 11.
9 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose).
10 Fig. 4 Fig. 5 Fig. 6 ASSEMBLING EXTENSION WING NOTE: CHECK TO SEE WHA T TYPE OF ST ARTER BOX WAS SHIPPED WITH YOUR SA W (GPE OR L VC). A GPE ST ARTER HAS ROUND “ON” AND “OFF” BUTTONS. A L VC ST ARTER HAS RECT ANGLE “ON” AND “OFF” BUTTONS.
11 ASSEMBLING L VC ST ARTER BOX TO CABINET If you purchased the machine with magnetic push button electrical controls, the saw is shipped with the starter box completely wired to the switch and motor . However , the starter box must be mounted to the saw cabinet.
12 ASSEMBLING GPE ON/OFF SWITCH 1. Locate the GPE switch and har dware that was removed in the section “ASSEMBLING EXTENSION WING.” 2. Loosely assemble switch and switch bracket (A) Fig.
13 Fig. 16 Fig. 17 Fig. 19 Fig. 18 Fig. 20 Fig. 21 4. If an adjustment is necessary , loosen two screws (F) Fig. 17, and adjust splitter bracket (A) until it is aligned with the inside blade flange (B) Fig. 15. Tighten two screws (F). Loosely assemble scr ew and fastener plate (C), which were r emoved in STEP 2.
14 Fig. 22 Fig. 23 Fig. 25 Fig. 24 Fig. 26 Fig. 27 5/16" lockwasher , then a 5/16" flat washer , onto a 5/16- 18x1" hex head screw (N), insert the scr ew (N) through the hole in the upper splitter bracket (M) and thread the screw into the lower splitter bracket (L).
15 Fig. 28 Fig. 30 Fig. 29 A TT ACHING MOTOR COVER NOTE: IF YOU HA VE AN “L VC” (ST ARTER BOX) VERSION UNISAW , YOU WILL HA VE TO A TT ACH TWO BOTTOM SPRING CLIPS TO THE MOTOR COVER. IF YOU HA VE AN “GPE” (ST ARTER BOX) VERSION UNISAW THE SPRING CLIPS ARE ALREADY A TT ACHED TO THE MOTOR COVER.
16 Fig. 36 ASSEMBLING RIP FENCE HOLDER BRACKETS Assemble the rip fence holder brackets (A) and (B) Fig. 37, to the four holes located in the right hand side of the saw cabinet using four #10 x 1/2" sheet metal screws supplied.
17 Fig. 39 A B Fig. 40 A BLADE RAISING MECHANISM The saw blade is raised and lowered with the fr ont handwheel (A) Fig. 41. With the exception of hollow ground blades, the blade should be raised 1/8" to 1/4" above the top surface of the material being cut.
18 ADJUSTING 90 AND 45 DEGREE POSITIVE STOPS Positive stops are pr ovided to quickly and accurately position the blade at 90 and 45 degrees to the table. T o check and adjust the positive stops, proceed as follows: DISCONNECT MACHINE FROM POWER SOURCE.
19 ADJUSTING T ABLE INSER T Place a straight edge (B) across the table at both ends of the table insert as shown in Fig. 46. The table insert (A) should always be level with the table. If an adjustment is necessary , turn the adjusting screws (C), as needed, with allen wrench supplied.
20 REPLACING BEL TS AND ADJUSTING BEL T TENSION DISCONNECT MACHINE FROM POWER SOURCE. 1. Remove motor cover to gain access to the motor . 2. Place a block of wood (C) Fig. 51, between the motor and saw cabinet as shown. NOTE: It may be necessary to raise the saw arbor in order to insert the wooden block.
21 Fig. 54 Fig. 55 C A B MACHINE USE COMMON SAWING OPERA TIONS Common sawing operations include ripping and crosscutting plus a few other standar d operations of a fundamental nature. As with all power machines, ther e is a certain amount of hazard involved with the operation and use of the machine.
WHEN USING YOUR UNIFENCE AS A CUT -OFF GAGE, MAKE SURE IT IS PROPERL Y SET UP AS DESCRIBED HERE. The Unifence can be used as a cut-off gage when cr oss cutting a number of pieces to the same length.
23 Fig. 61A Fig. 61 table, after which the work is lifted and brought along the outside edge of the fence. The cut-off stock remains on the table and is not touched until the saw blade has stopped, unless it is a lar ge piece allowing safe removal.
24 Fig. 64 H G A B Fig. 67 Fig. 65 Fig. 66 W H Moulding is cutting a shape on the edge or face of the work. Cutting mouldings with a moulding cutterhead is a fast, safe and clean operation.
25 C Fig. 68 SPECIAL A TTENTION SHOULD BE GIVEN THE GRAIN DIRECTION. MAKE ALL CUTS IN THE SAME DIRECTION AS THE GRAIN WHENEVER POSSIBLE. AL WA YS INST ALL BLADE GUARD AFTER OPERA TION IS COMPLETE. Fig. 69 Fig. 70 Fig. 71 A B C 1. Dadoing is cutting a rabbet or wide groove into the work.
Fig. 74 Fig. 75 Kerf should be about 1/4" apart. 26 3. Fig. 73, shows a typical dado operation using the miter gage as a guide. NEVER USE THE DADO HEAD IN A BEVEL POSITION. AL WA YS INST ALL BLADE GUARD AFTER OPERA TION IS COMPLETED. Fig. 74, illustrates dimensions for making a typical featherboard.
27 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HA.
28 TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).
29 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier .
30 T wo Y ear Limited New Product W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to.
31 NOTES.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
デバイスDelta 36-953の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Delta 36-953をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 36-953の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 36-953の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 36-953で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 36-953を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 36-953の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 36-953に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 36-953デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。