DeltaメーカーDP400の使用説明書/サービス説明書
ページ先へ移動 of 23
INSTRUCTION MANUAL 16½" Floor Model Drill Pr ess (Model DP400) P ART NO. A10352 - 03-28-05 Copyright © 2005 Delta Machinery ESP AÑOL: PÁGINA 23 T o learn more about DEL T A MACHINER Y visit our website at: www .
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury .
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL WARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage.
5 ADDITIONAL SPECIFIC SAFETY RULES F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS INJUR Y . 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according t o the instructions. A machine incorrectly assembled can cause serious injury .
6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
7 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-pr ong grounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
8 FOREWORD Delta ShopMaster DP400 is a 16½" drill press with a 120/240 V , 3/4 H.P . induction motor , a flexible work lamp and a tilting table with c-clamp edges and diagonal slots. The Delta ShopMaster Model DP400 has a 5/8” capacity chuck and a 3 3/8” stroke.
9 CAR TON CONTENTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 20 21 22 19 Fig. 2 1. Drill Press Head 2. T able 3. T able Bracket and Column 4. Light 5. Base 6. Chuck 7. Handle (3) 8. Spindle Adapter 9. Spindle Adapter Remover 10. 5mm Hex Wrench 11. 3mm Hex Wrench 12.
10 ASSEMBL Y FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. Fig. 4 Fig. 5 3" MINIMUM 3" MINIMUM 3" MINIMUM 3" MINIMUM 28" MINIMUM 21" MINIMUM C 1.
THE PL YWOOD BASE MUST BE SECURED TO THE FLOOR OR SUPPORTING SURF ACE IF THERE IS ANY TENDENCY OF THE DRILL PRESS TO VIBRA TE, SLIDE OR WALK DURING NORMAL OPERA TION. 11 6. Assemble the column (A) Fig. 6, to the base (B) using the four M10x40mm hex head screws (C), thr ee of which are shown.
12 Fig. 9 9. Insert table (H) Fig. 9, into hole in table bracket as shown. Fig. 10 10. Thread table locking lever (J) Fig. 10, into hole in front of table bracket as shown. Fig. 11 Fig. 12 11. Place the drill press head (K) Fig. 11, onto the column as far as it will go.
13 Fig. 14 14. IMPORT ANT : Make certain the spindle taper (O) Fig. 14, and tapered hole in chuck (P) ar e clean and free of any grease, lacquer or rust pr eventive coatings. NOTE: Household oven cleaner can effectively r emove any sub- stance from the chuck; however , carefully follow the manufacturer's safety rules concerning its use.
14 18. Align the two holes in the lamp bracket (A) Fig. 17, with the two holes (B) on the side of the drill press head. Fig. 17 20. Align the two holes in the lamp cord bracket (F) Fig. 18 with the two holes in the lamp bracket (A) and drill press head.
ST AR TING AND STOPPING DRILL PRESS The switch (A) Fig. 20, is located on the front of the drill press head. T o turn the drill press “ON” move the switch up to the “ON” position. T o tur n the drill press “OFF” move the switch down to the “OFF” position.
16 Fig. 24 C E 3. The table can be tilted right or left by pulling out and removing table alignment pin (C) Fig. 24. NOTE: If pin (C) is difficult to r emove, tur n nut (E) clockwise to pull pin out of casting. 4. Fig. 25, illustrates the table alignment pin (C) removed.
17 SPINDLE SPEEDS T welve spindle speeds are available on the drill press. Fig. 27, illustrates which steps of the pulleys the belts must be placed to obtain the twelve speeds available.
18 DRILLING HOLES TO DEPTH Where a number of holes ar e to be drilled to exactly the same depth, a depth stop is provided and is used as follows: DISCONNECT MACHINE FROM POWER SOURCE.
19 Fig. 32 Y our drill press is to be used with drill bits with a shank of 5/8" or less in diameter . The following will give the inexperi enced operator a start on common drill press operations. Use scrap material for practice to get a feel of the machine before attempting r egular work.
20 BORING IN WOOD T wist drills, although intended for metal drilling, may also be used for boring holes in wood. However , machine spur bits are generally pr eferred for working in wood; they cut a flat bottom hole and are designed for r emoval of wood chips.
21 TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).
22 MAINTENANCE P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and are serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
デバイスDelta DP400の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Delta DP400をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta DP400の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta DP400の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta DP400で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta DP400を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta DP400の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta DP400に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta DP400デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。