DeVilbissメーカーMG4-OLENG-2Bの使用説明書/サービス説明書
ページ先へ移動 of 20
MG4-OLENG-2B 5/1/99 GENERAL MANUAL FOR OIL LUBRICA TED SINGLE ST AGE GASOLINE ENGINE AIR COMPRESSOR This pr This pr This pr This pr This pr oduct is not equipped with a spark arr oduct is not equipped.
2 T ABLE OF CONTENTS Page SAFETY GUIDELINES ...................................... 2 WARRANTY STATEMENT .............................. 3 WARNING CHART ........................................ 4- 5 GLOSSARY .............................................
3 Retain original cash register sales receipt as proof of purchase for warranty work. Use reasonable care in the operation and maintenance of the product as described in the Owners Manual(s). Deliver or ship the product to the nearest DeVilbiss Air Power/ExCell Manufacturing Authorized Warranty Service Center.
4 RISK OF EXPLOSION OR FIRE RISK OF BURSTING GASOLINE AND GASOLINE VAPORS CAN BECOME IGNITED BY COMING INTO CON- TACT WITH HOT COMPONENTS SUCH AS THE MUFFLER, FROM ENGINE EXHAUST GASES, OR FROM AN ELECTRICAL SPARK. COMBUSTIBLE MATERIALS WHICH COME INTO CONTACT WITH HOT ENGINE PARTS CAN BECOME IGNITED.
5 HAZARD RISK FROM FLYING OBJECTS RISK TO BREATHING RISK FROM MOVING PARTS RISK OF BURNS WHAT CAN HAPPEN THE COMPRESSED AIR STREAM CAN CAUSE SOFT TISSUE DAMAGE TO EXPOSED SKIN AND CAN PROPEL DIRT, CHIPS, LOOSE PARTICLES AND SMALL OBJECTS AT HIGH SPEED , RESULTING IN PROPERTY DAMAGE OR PERSONAL INJURY.
6 GENERAL INFORMA TION You have purchased an air compressor unit consisting of a 2 cylinder, single-stage air compressor pump, an air tank, wheels, handle, associated controls and in- struments.
7 ON-RECEIPT INSPECTION Each air compressor outfit is carefully tested and checked before shipment. With improper handling, damage may result in transit and cause problems in compressor operation. Immediately upon arrival, check equipment for both concealed and visible damages to avoid expenses being incurred to correct such problems.
8 ASSEMBL Y INSTRUCTIONS Installing Handle, Foot Extension Bracket, Wheels, Outlet V alve THE WHEELS AND HANDLE DO NOT PRO- VIDE ADEQUATE CLEARANCE, STABILITY OR SUPPORT FOR PULLING THE UNIT UP AND DOWN STAIRS OR STEPS. THE UNIT MUST BE LIFTED OR PUSHED UP A RAMP.
9 INST ALLA TION AND BREAK-IN PROCEDURES Permanent Installation BOLTING LEGS TO A STIFF SURFACE CAN CAUSE TANK RUPTURE RESULTING IN SERIOUS INJURY OR DAMAGE.
10 INST ALLA TION AND BREAK-IN PROCEDURES For your convenience, purchase a 1/4" NPT nipple, 2 1/2" long, and a 1/4" NPT x 1/4" NPT coupling (pipe collar) to allow ease in draining oil. Remove oil drain plug on the gas tank side of the engine and install the nipple.
11 INST ALLA TION AND BREAK-IN PROCEDURES 2. Place your left hand on the air compressor handle, and your right hand on the starter handle, and pull cord out quickly to overcome engine compression and prevent "kickback".
12 MAINTENANCE DURING MAINTENANCE, YOU COULD BE EXPOSED TO COMPRESSED AIR OR MOVING PARTS. PERSONAL INJURIES CAN OCCUR. BEFORE DOING ANY MAINTENANCE OR REPAIR, DISCONNECT THE SPARK PLUG WIRE TO PREVENT ACCIDENTAL STARTING, AND RELIEVE AIR TANK PRESSURE.
13 MAINTENANCE Air Compressor A clean air compressor and engine run cooler and provide longer service. Clean or blow off fins and any other parts of the air compressor and engine that collect dust or dirt. Do not place tags, containers or other material on or against the ventilation openings in the belt guard.
14 MAINTENANCE Engine - Oil Change and Air Cleaner See Briggs & Stratton "Operating and Maintenance Instructions" for information regarding engine oil changes and air cleaner service as well as for warranty informa- tion. Turn the needle valve 1 1/2 revolutions counterclock- wise to establish a point of reference.
15 MAINTENANCE Belt - Replacement SERIOUS INJURY OR DAMAGE MAY OC- CUR IF PARTS OF THE BODY OR LOOSE ITEMS GET CAUGHT IN MOVING PARTS. NEVER OPERATE THE OUTFIT WITH THE BELT GUARD REMOVED. THE BELT GUARD SHOULD BE REMOVED ONLY AFTER THE SPARK PLUG WIRE HAS BEEN DISCON- NECTED.
16 TROUBLESHOOTING GUIDE CORRECTION CAUSE PROBLEM Air leaks in air tank. Defective air tank. Air tank must be replaced. Do not attempt repair of any leaks. DO NOT DRILL INTO, WELD, OR OTH- ERWISE MODIFY AIR TANK OR IT WILL WEAKEN. Air leak from safety valve.
17 TROUBLESHOOTING GUIDE CORRECTION CAUSE PROBLEM Compressor is not supplying enough air to operate accesso- ries. Prolonged excessive use of air. Compressor is not large enough for air requirement. Restricted air intake filter. Loose belt. Hole in hose.
18 SERVICE NOTES.
19 SERVICE NOTES.
GENERAL MANUAL FOR OIL LUBRICA TED SINGLE ST AGE GASOLINE ENGINE AIR COMPRESSOR Attach Sales Receipt Here Retain Original Sales Receipt as Proof of Pur chase for W arranty Repair W ork. WARRANTY This product is covered by the DeVilbiss one year limited warranty .
デバイスDeVilbiss MG4-OLENG-2Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
DeVilbiss MG4-OLENG-2Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDeVilbiss MG4-OLENG-2Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。DeVilbiss MG4-OLENG-2Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。DeVilbiss MG4-OLENG-2Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
DeVilbiss MG4-OLENG-2Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDeVilbiss MG4-OLENG-2Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、DeVilbiss MG4-OLENG-2Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDeVilbiss MG4-OLENG-2Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
