DolmarメーカーHT-2556 D, HT-2576 Eの使用説明書/サービス説明書
ページ先へ移動 of 20
Instruction Manual Important: Read this instruction manual carefully before putting the hedge trimmer into operation and strictly observe the safety regulations! Keep this instruction manual! HT -2556 D http://www .
2 T able of contents Page Conformity Declaration ...................................................... 2 Packaging ............................................................................ 2 Delivery inventory .....................................
3 4 Delivery inventory 1. Hedge trimmer HT -2576 E (depending on order) 2. Hedge trimmer HT -2556 D (depending on order) 3. Knife guard 4. Universal wrench 5. Instruction Manual (not shown) In case one of the parts listed should not be included in the delivery inventory , please consult your sales agent.
4 5 1 4 3 2 SAFETY PRECAUTIONS General precautions - In order to ensure safe operation, the operator must read this instruction manual to familiarize him or herself with the operation of the hedge trimmer . Users insufciently informed will endanger themselves as well as others due to improper handling.
5 6 7 10 9 8 - Fuels can contain substances similar to solvents. Eyes and skin should not come in contact with mineral oil products. Always wear protective gloves when refuelling. Frequently clean and change protective clothes. Do not breathe in fuel vapors.
6 - After use, clean the trimmer , in particular the cutter . Oil the cutter lightly and put on the blade guard. - Emtpy the fual tank completely before long-term storage or shipping the trimmer .
7 1 Rear grip 2 Safety cutoff 3 Throttle lever 4 ON/OFF (I/O) switch 5 Starter grip 6 Fuel tank cap Stroke volume cm 3 24,5 24,5 Max. power at speed kW / rpm 0,88 / 7.000 0,88 / 7.000 Idling speed / Max. engine speed with cutter rpm 2.600 / 9.800 2.600 / 9.
8 + A Gasoline It is not wise to add more engine oil than specied to ensure safe operation. This will only result in a higher production of combus-tion residues which will pollute the environment and clog the exhaust channel in the cylinder as well as the mufer .
9 B C Refuelling FOLLOW THE SAFETY PRECAUTIONS! Be careful and cautious when handling fuels. Refuel only with the engine switched off and cooled down! Thoroughly clean the area around the caps, to prevent dirt from getting into the fuel tank.
10 D E 7 Cold start: Move the ON/OFF ( I / O ) switch ( 2 ) to position “I” . T urn the starting lever ( 6 ) to the ST ART position. Press the fuel pump ( 5 ) several (7-10) times to supply fuel to the carburetor . Assume the starting position (see above under Starting posi- tion ).
1 1 1 2 3 4 Tips on trimming hedges The procedure described here can be used very often and makes working easier . If a hedge has to be cut back very substantially , it should be trimmed in two passes. The trapezoidal form shown prevents the lower portion of the hedge from thinning out due to lack of light.
12 A B STOP C STOP Cleaning and care Caution: Be especially careful when cleaning and caring for the cutter (injury hazard!). Never touch the cutter with bare hands. Always wear protective gloves! Regularly check the cutter for damage and clean it with a sui- table brush or cloth.
13 D E F STOP Checking the mufer bolts / cleaning the exhaust outlet Caution: Do not tighten the mufer bolts when the engine is hot! The mufer bolts ( 6 ) are directly accessible so they can be checked for tightness. If loose, hand-tighten (caution: do not over-tighten).
14 G Replacing the suction head The felt lter ( 8 ) of the suction head can become clogged. It is recommended to replace the suction head once every three months in order to ensure unimpeded fuel ow to the carburetor .
15 Service, spare parts and guarantee Workshop service The maintenanceand repair of modernhedge trimmers aswell as all safetydevices require qualiedtechnical training and aspecial workshop equipped with special tools and testing devices.
16 Pos. DOLMAR-No. Qty . Denomination 1 377 601 400 1 T ank cap, cpl. 2 382 650 390 1 Suction head 3 374300401 1 Airlterinsert 4 381 014 981 1 Spark plug - 944 340 001 1 Screwdriver - 944 350 000 1 Grease gun Extract from the spare parts list Use only original DOLMAR parts.
17 Notes.
18 Notes.
19 Notes.
Form: 995 701 252 (3.06 GB) Specicationssubjecttochangewithoutnotice DOLMAR GmbH Postfach 70 04 20 D-22004 Hamburg Germany http://www .
デバイスDolmar HT-2556 D, HT-2576 Eの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dolmar HT-2556 D, HT-2576 Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDolmar HT-2556 D, HT-2576 Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dolmar HT-2556 D, HT-2576 Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dolmar HT-2556 D, HT-2576 Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dolmar HT-2556 D, HT-2576 Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDolmar HT-2556 D, HT-2576 Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dolmar HT-2556 D, HT-2576 Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDolmar HT-2556 D, HT-2576 Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。