EchoメーカーRM-210SBの使用説明書/サービス説明書
ページ先へ移動 of 32
Grass T rimmer/Brush Cutter Operator's Manual MODEL SRM - 210SB W ARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual with this unit and a separate Operator's Manual and Safety Manual (if available) with the attachment.
2 I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 3 This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders. The circle with the slash symbol means whatever is shown within the circle is prohibited.
4 with shield in place. Operators, helpers and bystanders must wear ANSI Z87.1 approved eye protection. • Always wear hearing protection when operating unit. • Prevent accidental contact with unit and any cutting attachment. Maintain a 15M (50 ft.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 5 S AFETY I NSTRUCTIONS PERSONAL CONDITION AND SAFETY EQUIPMENT W ARNING DANGER Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly or safety precautions are not followed.
6 Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI).
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 7 IMPORTANT ENGINE INFORMATION ENGINE FAMILY: 4EHXS.0214EF DISPLACEMENT: 21.2 CC EMISSION COMPLIANCE PERIOD: 300 HOURS THIS ENGINE MEETS U.S. EPA PH2 EMISSION REGULA- TIONS FOR SMALL NONROAD ENGINE.
8 CONTENTS ____ 1 - Power Head w/Upper Drive Shaft Assembly ____ 1 - Lower Drive Shaft Assembly ____ 1 - Operator's Manual ____ 1 - Safety Manual ____ 1 - Warranty Registration Card ____ 1 - Limi.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 9 22 1 3 4 5 7 8 9 10 11 2 6 12 12 18 11 13 14 15 16 17 19.
10 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter. 2. GRIP - Rear (right hand) handle. 3. THROTTLE TRIGGER LOCKOUT - Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 11 S PECIFICA TIONS * Install and use U-Handle when operating any model with steel blade. **The RPM range shown applies for all attachments. Refer to your attachment Operator's Manual "Specifications" section for proper RPM specifications.
12 ECHO APPROVED OPTIONAL A TT ACHMENTS • PAS Edger Model 99944200470 • PAS Cultivator Model 99944200510 • PAS Trimmer Model 99944200540 • PAS Hedge Clipper Model 99944200480 • PAS Power Pru.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 13 A SSEMBL Y POWER HEAD SHAFT / LOWER SHAFT ASSEMBL Y Tools Required: None Parts Required: Split Boom Attachment Assembly 1 . Set Power Head/Shaft Assembly on a level surface. 2 . Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock- out position.
14 PLASTIC SHIELD INST ALLA TION (For Nylon Line Operation) Tools Required: Screwdriver Parts Required: Plastic Shield, Shield Plate, three (3) 5mm x 16mm screws NOTE The plastic shield is for use with the Nylon Line Head only. Install Metal Shield when using plastic or metal blades.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 15 P RE - O PERA TION OPERA TION WITH BLADES Preparing the Trimmer/Brush Cutter for Blade Use WARNING DANGER Blade use DEMANDS specific Brush Cutter configuration. Operation without specified shield and harness can result in serious personal injury.
16 8 Tooth Weed/Grass Blade (P/N 69600120331) is designed for grass, garden debris and thick weeds. DO NOT use this blade for brush or heavy woody growth, 19 mm (3/4 in.) diameter or larger. 80 Tooth Brush Blade (P/N 69500120331) is designed for cutting brush and woody growth up to 64 mm (2-1/2 in.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 17 IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. Contact your ECHO dealer for ordering information.
18 O PERA TION ST ARTING COLD ENGINE W ARNING DANGER The attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury. Keep movable parts of the attachment off the ground and away from objects that could become entangled or thrown.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 19 ST ARTING W ARM ENGINE The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position. W ARNING DANGER The attachment should not move at idle, otherwise serious personal injury may result.
20 M AINTENANCE Your ECHO unit is designed to provide many hours of trouble-free service. Regular scheduled maintenance will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 21 AIR FIL TER Level 1. Tools required: 25 - 50 mm (1 or 2 in.) Cleaning brush Parts required: 90008 REPOWER TM AIR & FUEL FILTER KIT. 1 . Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air filter is removed.
22 SP ARK PLUG Level 2. Tools required: T-Wrench (combination socket wrench and screw driver), Feeler gauge, brush. Parts Required: REPOWER TM Tune-Up Kit P/N 90074 1 . Remove spark plug and check for fouling, worn and rounded center electrode. 2 . Clean the plug or replace with a new one.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 23 1 . Remove spark plug lead from spark pulg. 2 . Remove the four screws that retain the engine cover (A). Two at the top of the recoil starter, one in the arm rest and on the muffler cover.
24 Cylinder Exhaust Port Level 3 IMPORTANT The cylinder exhaust port must be inspected and cleaned of excess carbon every 3 months or 90 hours of operation in order to maintain this engine within the emissions durability period. ECHO strongly recommends that you return your unit to your ECHO dealer for this important maintenance service.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 25 LUBRICA TION Level 1. Tools Required: 13 mm Open End Wrench, Screwdriver, Clean rag, Grease gun P/N 91016 Parts Required: ECHO ® LUBE TM 8 oz.
26 D A B B E A C D F Drive Shaft Upper 1 . Loosen clamping knob (A). 2 . Pull locator pin (B) and rotate 1/4 turn counter clockwise to lockout position. 3 . Remove attachment. 4 . Remove coupler (E) from upper drive shaft assembly by loosening clamping screw (C) and removing set screw (D).
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 27 D C F F E CC NYLON LINE REPLACEMENT Level 1. Parts Required: ECHO 0.095 in. Nylon Trimmer Line 6 m (20 ft.) long. 1 . Shut engine off. Lay unit on the ground with head assembly up. 2. Hold drum (A) and firmly turn spool (B) CW (clockwise) until it disengages from the inner drive.
28 6 . Feed ends of line through housing eyelets (G) and place spool (B) over drive (H). Align pegs (I) on drive with notches in spool, and push spool into drum. 7 . Pull on both lines until they come free from notches (F) in spool. B A I G G B H F F B 8 .
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 29 SHARPENING MET AL BLADES Three styles of metal blades are approved for use on the ECHO Brush Cutter. The 8-tooth blade can be sharpened during normal maintenance. The clearing blade and 80 tooth blade require professional service.
30 T R A H C G N I T O O H S E L B U O R T M E L B O R P E N I G N E m e l b o r Pk c e h Cs u t a t Se s u a Cy d e m e R e n i g n E - s k n a r c / d r a h s t r a t s t ' n s e o d t r a t s .
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 31 S TORAGE Long Term Storage (over 30 days) W ARNING DANGER During operation the muffler or catalytic muffler and surrounding cover become hot.
S ER VICING I NFORMA TION P ARTS Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number and Serial Number of the unit with you.
デバイスEcho RM-210SBの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Echo RM-210SBをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEcho RM-210SBの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Echo RM-210SBの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Echo RM-210SBで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Echo RM-210SBを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEcho RM-210SBの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Echo RM-210SBに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEcho RM-210SBデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
