EchoメーカーX750-005 05 7の使用説明書/サービス説明書
ページ先へ移動 of 24
OPERA TOR’S MANUAL ENGINE DRILL EDR-260 X750-005 05 7 X750409-3607 W ARNING READ INSTRUCTIONS CAREFULLY AND FOLLOW RULES FOR SAFE OPERATION. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
W ARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
1 CAUTION The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided. WARNING IMPROPER USE OR CARE OF THIS UNIT, OR FAILURE TO WEAR PROPER PROTECTION CAN RESULT IN SERIOUS INJURY.
2 WARNING ALWAYS STOP THE ENGINE WHEN A DRILL JAM OCCURS. DO NOT ATTEMPT TO REMOVE AN OBJECT CAUSING A DRILL JAM IF THE ENGINE IS RUNNING. PHYSICAL INJURY CAN OCCUR IF A DRILL JAM IS REMOVED AND THE DRILLS START MOVING. • Do all drilling at full throttle speed.
3 • Wear non-slip, heavy-duty work gloves to improve your grip on the engine drill handles. The gloves also help reduce the transmission of machine vibrations to your hands. PR O TECTING O THERS Spectators, children, fellow workers and animals must be warned to come no nearer than 4.
4 Repetitive Stress Injuries It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI).
5 • Do not force the drills and only move as quickly as the drills will allow. • Stop the engine and disconnect from ignition cable before: - cleaning or when clearing a blockage; checking, maintenance or working on the machine. • Handle fuel with care; it is highly flammable.
6 DESCRIPTION 1. Operator’s manual - Included with unit. Read before operation and keep for future reference to learn proper, safe operating techniques. 2. Throttle trigger - Device activated by the operator’s finger, for controlling the engine speed.
7 ASSEMBLING FR ONT HANDLE • Insert the front handle to the machine, and turn clockwise. (TIGHTEN THE SCREW FIRMLY) - To operate front handle with right hand, remove right plug then reverse sides when installing handle and plug.
8 CHECK UP OF NUTS AND O THER HARD W ARES • Check up loose nuts, bolts and screws before using the unit every day. FUEL ST A TEMENT GASOLINE - Use 89 Octane [(R+M)/2] (mid grade or higher) gasoline or gasohol known to be good quality . Gasohol may contain up to 10 % Eth yl (grain) alcohol or 15 % MTBE (meth yl ter tiar y-butyl ether).
9 HANDLING FUEL MIXING INSTRUCTIONS - 1. Fill an approv ed fuel container with half of the required amount of gasoline. 2. Add the proper amount of two-strok e oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container , and remix.
10 ON STOP Throttle trigger NOTE When engine does not stop, shift choke lever to close position. Check and repair ignition switch before starting the engine again. ST ARTING COLD ENGINE ST OPPING ENGINE • Set throttle trigger in idle position. • Place ignition switch in STOP position.
11 REVERSE RO T A TION • This model is equipped with reverse rotation mechanism. • When drilling, set shift lever down to clockwise (CW) rotation position. • If bit is locked due to deep penetration during drilling operation, set shift lever up to counterclockwise (CCW) rotation position and operate reversed for easy pulling-out.
12 IMPORTANT Time intervals are maximum. Actual use and your experience will determine the frequency of required maintenance. Record dates of monthly and yearly inspections.
13 TR OUBLE SHOO TING Trouble Engine - hard to start Cause Remedy - does not start Engine Fuel at No fuel • Fuel filter clogged • Clean or replace cranks carburetor at carburetor • Fuel line cl .
14 MAINTENANCE AIR FIL TER • Clean before use. - Remove air cleaner cover and pull out air filter. - Lightly brush off dust or wash it in water and detergent. - Dry completely before putting it back in place. Fuel filter Fuel tank cap SP ARK PLUG • Check periodically.
15 ADJUSTING CARBURET OR (As Required) GENERAL INFORMATION The idle speed adjuster screw controls the throttle opening at the idle position. IDLE ADJUSTMENT 1. Start engine and allow it to run at high idle until warm. 2. Turn the idle speed screw clockwise until drill bit begins to move.
16 CLEANING CYLINDER FINS (Chec k P er iodically) NOTE Clogged fins will cause poor engine cooling. 1. Carefully remove housing and clean dirt and dust from fins. 2. Reinstall housing. CLEANING SILENCER AND EXHA UST PORT (Chec k P er iodically) 1. Carefully remove housing halves.
17 ST ORA GE 6. Drain the fuel tank completely and pull the recoil starter handle several times to remove fuel from the carburetor. 7. Remove the spark plug and pour 1/2 tablespoon (1/4 oz) of fresh, clean, 2-stroke engine oil into the cylinder through the spark plug hole.
18 SPECIFICA TIONS EDR-260 Mass without drill bit kg 5.18 (11.42 lb) Volume fuel tank L 0.58 (19.6 US fl. oz.) Drill size mm 32 - 178 (1.25 - 7 inch) chuck capacity mm 13 (0.
19 W ARRANTY ST A TEMENTS ECHO LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited W arranty , provides to the original purchaser that this ECHO product is free from defects in materia l and workmanship.
20 PURCHASED REP AIR P ARTS, SHORT BLOCKS AND ACCESSORIES GDUHVLGHQWLDORUQRQLQFRPHSURGXFLQJZDUUDQW GDFRPPHUFLDOLQVWLWXWLRQDODJUL.
21 ECHO INCORPORA TED EMISSION CONTROL W ARRANTY ST A TEMENT FOR ECHO AND SHINDAIW A BRANDS The Environmental Protection Agency (EP A) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) a re pleased to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE).
22.
デバイスEcho X750-005 05 7の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Echo X750-005 05 7をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEcho X750-005 05 7の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Echo X750-005 05 7の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Echo X750-005 05 7で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Echo X750-005 05 7を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEcho X750-005 05 7の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Echo X750-005 05 7に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEcho X750-005 05 7デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。