EchoメーカーX753001923の使用説明書/サービス説明書
ページ先へ移動 of 16
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 1 P AS Articulating Hedge Clipper Att achment Operator's Manual MODEL 99944200595 FOR MODELS: SRM-2100SB/2400SB SRM-21.
2 Copyright© 2009 By Echo, Incorporated All Rights Reserved. I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job-dependability. Read and understand this manual included with your attachment.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 3 Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.
4 Physical Condition Your judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye Protection Wear eye protection that meets ANSI Z87.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 5 DANGER Do not operate this product indoors or in inadequately ventilated areas.
6 EQUIPMENT • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. • Never adjust blades when the engine is operating. • Inspect hand guard for damage. Replace if damaged or missing. • Check that the blade assembly is firmly attached and in safe operating condition.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 7 1. CUTTING BLADES - Double reciprocating blades mounted to a blade support bar. Double sided blades, are capable of cutting on either side of the blade. 2. LOWER DRIVE SHAFT ASSEMBLY - Includes the Gear Housing assembly, Flexible Drive Cable, Blade and Safety Decals.
8 D C A A SSEMBL Y POWER HEAD SHAFT / LOWER SHAFT ASSEMBL Y A B D E C Tools Required: None Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling. 1 . Set Power Head/Shaft Assembly on a level surface. 2 . Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock- out position.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 9 ADJUSTING CUTTING ANGLE W ARNING Never adjust cutting assembly with engine running. W ARNING Hedge clipper blades are sharp. Always wear gloves when adjusting cutting assembly, otherwise serious injury may result.
10 ROT A TE CUTTER ASSEMBL Y Always use the unit from the right-hand side of your body – NEVER from the left side. Rotate cutter assembly 180 degrees on driveshaft in order to avoid cutting directly above your head, and to avoid contact with hot muffler.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 11 M AINTENANCE W ARNING Moving parts can amputate fingers or cause severe injuries.
12 IMPORTANT Flat edge of washer (D) must be against drive shaft. A A Gear Housing Level 1. Tools required: Grease Gun, Rag. Parts required: POWER BLENDX TM 14 oz. Cartridge P/N 91015 Grease or Lithium-based Grease. 1 . Clean dirt from grease fittings (A).
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 13 SHARPENING BLADES Level 3. Tools required: Flat file, screwdriver Parts required: None W ARNING Hedge Clipper Blades are very sharp. Wear gloves to protect hands. 1 . Disconnect spark plug wire from spark plug.
14 BLADE ADJUSTMENT Level 2. Tools required: (2) 10 mm Sockets & Extensions Parts required: None W ARNING Hedge clipper blades are very sharp. Touching them may lead to severe personal injury. Use a socket and extension when adjust- ing blade bolts or blade locknuts in order to keep hands at a safe distance from sharp blades.
P AS A RTICULA TING H EDGE C LIPPER A TT ACHMENT O PERA TOR ' S M ANUAL 15 Length ------------------------------------------------------- 1016 mm (40.0 in.) Attachment Width ----------------------------------------- 132 mm (5.2 in.) Height ------------------------------------------------------- 127 mm (5.
DEALER? Call 1-800-432-ECHO or www .echo-usa.com CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T. ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047-1564 www .
デバイスEcho X753001923の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Echo X753001923をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEcho X753001923の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Echo X753001923の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Echo X753001923で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Echo X753001923を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEcho X753001923の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Echo X753001923に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEcho X753001923デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。