Elektra BeckumメーカーPK 255 3の使用説明書/サービス説明書
ページ先へ移動 of 20
PK 255 D Betriebsanleitung Systemkreissäge G Operating Instruction System circular saw F Instructions d'utilisation Scie circuaire à système 25 20 15 10 5 0 30 35.
D Die beiliegende Garantiekarte senden Sie bitte an uns zurück. Den Kaufbeleg bitte aufbewahren! Ein Anspruch auf Garantieleistungen besteht nur gegen Vorlage des Kaufbelegs. Die Adresse Ihrer nächstgelegenen Werksvertretung finden Sie auf der hinteren Umschlagseite.
2.1 PK 255 Scope of delivery 25 20 15 10 5 0 30 35 1 2 3 4 5 6 1 System circular saw with saw blade 2 Blade guard hardware bag 3 Rip fence with auxiliary fence extrusion 4 Push stick / feeding aid 5 Leg with foot (4x) 6 Connector suction hose / chip case XA0011E.
2.2 PK 255 Saw components and controls 25 20 15 10 5 0 30 35 1 2 3 4 5 6 7 8 9 10 1 Saw blade 2 Riving knife 3 Blade guard 4 Rip fence with auxiliary fence extrusion 5 Push stick / feeding aid 6 Handw.
2.3 PK 255 Please read first! · Read these instructions before commissioning. Pay special attention to the safety information. · If you notice a transport damage while unpack- ing, notify your supplier immediately. Do not operate the machine! · Dispose of the packing environmentally friendly.
2.4 PK 255 Symbols shown on the machine A Danger! Disregard of the following warnings can lead to severe personal injury or material damage. Read instructions. Do not reach into the revolving saw blade. f Wear hearing protection. Use push stick if distance between saw blade and rip fence is £ 120 mm.
2.5 PK 255 Operating controls On/off switch with emergency stop · To switch ON = press green button. · To switch OFF = press red button or cover of on/ off switch. 3 An undervoltage relay trips in the event of a voltage failure, to prevent a restarting of the saw when the power is restored.
2.6 PK 255 Rip fence The rip fence slides onto the saw from the right- hand side and locks on the saw’s front. The auxiliary fence extrusion can be repositioned after loosening the two wing nuts: · small edge (as shown): - for cutting thin stock; - when the saw blade is tilted.
2.7 PK 255 Dust collection from chip casing 1. Turn saw upside down. 2. Remove transport support inside the saw hous- ing. 3. Attach suction port to chipcase with - 3 ea. hex. head screw M 6x13 - 3 ea. washer - 3 ea. serrated lock washer - 3 ea. hexagon nut M 6 3 If you are using a dust collector, connect to the chip case's suction port.
2.8 PK 255 Mains connection B Danger! Electrical Hazard Operate saw in dry environment only. Operate saw only on a power source match- ing the following requirements (see also "Technical specific.
2.9 PK 255 Rip cuts with rip fence 1. Lock rip fence in required position on saw table. A Danger! Use push stick if distance between rip fence and saw blade is less than 120 mm. 2. Reposition auxiliary fence extrusion if neces- sary: - Low edge (as shown) = for sawing thin stock; and with a tilted saw blade.
2.10 PK 255 6. To block the saw blade insert lock bar into hole in the saw table and turn saw blade by hand until lock bar engages in saw spindle hole. 7. Loosen saw blade spindle arbor nut with span- ner (L.H. thread!). 8. Take outer blade collar and saw blade off the saw spindle.
2.11 PK 255 5. Turn saw over and place on its saw table. 6. Loosen the two nuts inside the saw by approx. one turn. 7. Stand saw back on its feet/workstand. 8. Adjust saw blade position by turning the setting nuts. 9. Turn saw over again and place on its saw table.
2.12 PK 255 1. Take blade guard off. 2. Remove the two fastening screws of the remov- able table section. 3. Raise blade fully. 4. Lift chip case cover slightly and swing to the side. The cover is hooked into the bottom of the chip case and can not fall down.
2.13 PK 255 Universal fence adjustments 1. Check if fence is square against saw blade with a try square. 2. If necessary, loosen fixing screws and adjust mitre scale.
2.14 PK 255 Troubleshooting A Danger! Before carrying out any fault service or main- tenance work always: - Switch machine OFF. - Unplug power cable. - Wait for saw blade to come to standstill. Check that all safety devices are operational again after each fault service.
2.15 PK 255 Technical specifications Available saw blades Single-phase motor Three-phase motor Voltage V 230 (1 ~ 50 Hz) 400 (3 ~ 50 Hz) Rated current A 11.0 6.0 Fuse protection min. A 1 x 10 time-lag 3 x 16 time-lag Protection class IP 44 IP 44 Motor speed min -1 2800 2800 Motor capacity input P 1 output P 2 kW kW 2.
2.16 PK 255 Circuit diagrams Single-phase motor Three-phase motor.
Aktiengesellschaft Postfach 13 52, D-49703 Meppen EG-Konformitätserklärung - EC conformity declaration - Déclaration de conformité CEE EG-verklaring van overeenstemming - EF-overensstemmelsesattes.
PK 255 – A0017RL 115 162 1380 D/GB/F 2 7 98 4.0 B Belgium Elektra Beckum Belgium N.V.S.A. Industriezone Hofte te Bollebeeklaan B-1730 Asse-Mollem Tel.: 0032-24540454 Fax: 0032-24540450 D Deutschland Elektra Beckum AG Daimlerstraße 1 D-49716 Meppen Tel.
デバイスElektra Beckum PK 255 3の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Elektra Beckum PK 255 3をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはElektra Beckum PK 255 3の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Elektra Beckum PK 255 3の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Elektra Beckum PK 255 3で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Elektra Beckum PK 255 3を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はElektra Beckum PK 255 3の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Elektra Beckum PK 255 3に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちElektra Beckum PK 255 3デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。