Aleratecメーカー280118の使用説明書/サービス説明書
ページ先へ移動 of 50
® USER GUIDE Aleratec 1:3 DVD/CD RoboRacer MultiDrive SA™ Part No. 280118, 280118EU.
www .aleratec.com Copyright/Model Identication The content of this manual is for informational purposes only and is subject to change without notice.
www .aleratec.com Radio/TV Interference Statement The equipment described in this guide emits radio frequency energy . If it is not installed in accordance with the manufacturer ’ s instructions, it may cause interference with radio or television reception.
www .aleratec.com Safety Regulations WARNING T o prevent re or shock hazard, do not expose the unit to rain or moisture. T o avoid electrical shock, do not open the cabinet. Refer servicing to authorized personnel only . CAUTION As the laser beam in these DVD/CD Duplicators is harmful to the eyes, do not attempt to disassemble the cabinet.
www .aleratec.com Table of Contents Introduction .......................................................................................... 1 Included Items ............................................................................................ 1 Key Items – 1:3 DVD/CD RoboRacer MultiDrive SA .
www .aleratec.com ®.
www .aleratec.com 1 Introduction Thank you for purchasing this 1:3 DVD/CD RoboRacer MultiDrive SA. Please read this User Guide thoroughly before using this product. • Page 2 shows the Key Features of the 1:3 DVD/CD RoboRacer MultiDrive SA • Page 3 shows the Duplicator LCD Display Panel.
www .aleratec.com 2 Introduction Key Items – 1:3 DVD/CD RoboRacer MultiDrive SA 1 5 8 A B 1. ClearPlasticDiscGuideRods 2. LCDDisplayPanel 3. ControlPanel 4. DiscBurningDrives 5. DiscInputBin 6. ProtectiveCover 7.
www .aleratec.com 3 Introduction 1:3 DVD/CD RoboRacer MultiDrive SA Display Panel 1 Display shows all functions and messages 2 Power Indicator - this LED also doubles as an activity LED and changes colors when a disc is being burned etc.
www .aleratec.com 4 Precautions Before installing your 1:3 DVD/CD RoboRacer MultiDrive SA, please read the following. Installation A void placing the 1:3 DVD/CD RoboRacer MultiDrive SA in a location s.
www .aleratec.com 5 Overview Main Menu This section provides a listing of the functions on the 1:3 DVD/CD RoboRacer MultiDrive SA. Detailed descriptions of each function are given in the next section. There are 5 main menu items that will display in the 1:3 DVD/CD RoboRacer MultiDrive SA Display Panel.
www .aleratec.com 6 Image Load Image Delete Image Burn Image Compare Image Overview Subfunctions The main menu “Image” function has 4 subfunctions.
www .aleratec.com 7 Overview Subfunctions The main menu “Setup” function has 16 subfunctions. These are: Setup Copy Mode Demo Run Load Firmware Max Disc Errors CD Burn Speed DVD Burn Speed Default.
www .aleratec.com 8 Using the DVD/CD Duplicator Main Menu: Disc Duplicate This is the default mode of the 1:3 DVD/CD RoboRacer MultiDrive SA controller . This function will activate the duplication process. 1. Load a source disc in the input bin and load blank discs for the number of copies needed.
www .aleratec.com 9 Using the DVD/CD Duplicator Main Menu: Compare Compare will perform a bit by bit comparison of the disc copies loaded on the input bin to the source disc. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Compare” function.
www .aleratec.com 10 Using the DVD/CD Duplicator Main Menu: Image - continued ImageLoad “Image Load” will copy an image of a source disc loaded in the input bin to a chosen hard drive partition. 1. Press ENTER ( ENT ) key to enter the subfunction menu.
www .aleratec.com 11 Using the DVD/CD Duplicator 4. Press ENTER ( ENT ) and select the partition to be compared. 5. Press ENTER ( ENT ) to start. 6. Use the ESCAPE ( ESC ) key to return to the Main Menu. ImageBurn This function will select the source image from the hard drive and burn the desired number of copies.
www .aleratec.com 12 Using the DVD/CD Duplicator Main Menu: Image - continued ImageDelete Using this function you can select a partition to be deleted from the hard drive. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Image” function.
www .aleratec.com 13 Using the DVD/CD Duplicator Main Menu: USB Mode The “USB mode” activates the connection from the 1:3 DVD/CD RoboRacer MultiDrive SA built in hard disk drive to a PC. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “USB Mode” function.
www .aleratec.com 14 Using the DVD/CD Duplicator Main Menu: USB Mode - continued First install the Image Manager software included on the Software/User Guide CD. UsingImageManager 1. Once the Image Manager software is installed, put the RoboRacer MultiDrive SA into USB Mode and connect the device to your PC.
www .aleratec.com 15 Using the DVD/CD Duplicator 6. Click on the table row to choose which partition you will load the image onto. The row selected will be highlighted in blue. The letter you see in the Index column is the same as the letter used to locate the image when you return the duplicator back to stand alone mode (USB Mode off).
www .aleratec.com 16 Using the DVD/CD Duplicator Main Menu: USB Mode UsingImageManager - continued 8. Once you click Open you will see the Information screen appear . Click the OK button to begin loading the disc image. 9. The Manage Images screen will appear and display the status of the image load.
www .aleratec.com 17 Using the DVD/CD Duplicator 1 1. If you would like to edit the image information so that you can easily nd the image, select the “Edit T itle” button at the top of the Manage Images screen to add a description to the selected image le.
www .aleratec.com 18 Using the DVD/CD Duplicator T roubleshootingImageManager 1. If the Image manager is not starting and the screen displays this Error message, please make sure that the duplicator is in USB Mode. The duplicator ’ s screen will display as “Leave USB Mode, Press ESC Key” while it is in USB Mode.
www .aleratec.com 19 Using the DVD/CD Duplicator Main Menu: Setup 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Setup” function.
www .aleratec.com 20 Using the DVD/CD Duplicator Main Menu: Setup - continued CopyMode 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Setup” function. 2. Press ENTER ( ENT ) key to enter the subfunction menu “Copy Mode”.
www .aleratec.com 21 Using the DVD/CD Duplicator Main Menu: Setup - continued DemoRun This function activates a demo mode in which the 1:3 DVD/CD RoboRacer MultiDrive SA automatically cycles discs without simulating or burning any data on them. The mode can be run with or without discs being loaded in the device.
www .aleratec.com 22 Using the DVD/CD Duplicator Main Menu: Setup - continued MaxDiscErrors This function species the number of disc failures allowed before the duplicator will cancel the job. For example, if max disc errors is set to three, then a copy job will cancel once three target discs fail due to error .
www .aleratec.com 23 Using the DVD/CD Duplicator Main Menu: Setup - continued EraseDisc This function erases DVD-R W and CD-R W discs. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Setup” function. 2. Press ENTER ( ENT ) key to enter the subfunction menu.
www .aleratec.com 24 Using the DVD/CD Duplicator Main Menu: Setup - continued SystemSound This function turns the button sounds ON or OFF . 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Setup” function. 2. Press ENTER ( ENT ) key to enter the subfunction menu.
www .aleratec.com 25 Using the DVD/CD Duplicator Main Menu: Setup - continued T estModeSet In test mode the duplicator will simulate burning but will not actually write data to the disc. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Setup” function.
www .aleratec.com 26 Using the DVD/CD Duplicator Main Menu: Setup - continued FormatHardDisk 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Setup” function. 2. Press ENTER ( ENT ) key to enter the subfunction menu. 3. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Format hard disc”.
www .aleratec.com 27 Using the DVD/CD Duplicator Main Menu: Setup - continued DefaultReload Selecting “Y es” will return all settings to the factory default. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Setup” function.
www .aleratec.com 28 Using the DVD/CD Duplicator Main Menu: Setup - continued DVDBurnSpeed The “DVD burn speed” function allows adjustment of burn speed to increase yield and quality of copies. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Setup” function.
www .aleratec.com 29 Using the DVD/CD Duplicator Main Menu: Setup - continued CDBurnSpeed The “CD burn speed” function allows adjustment of burn speed to increase yield and quality of copies. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Setup” function.
www .aleratec.com 30 Using the DVD/CD Duplicator Main Menu: Setup - continued AutoV erify The “Auto V erify” function will test a disc for its readability in a ROM drive. This is not the same as “Compare”. Enabling “Auto V erify” will perform “V erify” on all disc copies loaded in the input bin.
www .aleratec.com 31 Using the DVD/CD Duplicator Main Menu: Setup - continued ReadErrorSkip If the source disc is damaged or of poor quality , enabling this function may allow making a useable copy . W ith Read error skip disable, burning will continue even if errors are detected.
www .aleratec.com 32 Using the DVD/CD Duplicator Main Menu: Setup - continued OverBurnMode When enabled, this function will burn data to a normally unused area along the outer diameter of the disc. This feature can increase the disc capacity by a small amount.
www .aleratec.com 33 Using the DVD/CD Duplicator Nero Essentials Installation 1. Insert the Nero 7 Essentials CD into your PC. If Autoplay is enabled on your computer , you will automatically be taken to the Nero Essentials installer menu.
www .aleratec.com 34 Using the DVD/CD Duplicator Creating an Image with Nero 1. Start the Nero Express Essentials program. 2. The screen below will be displayed.
www .aleratec.com 35 Using the DVD/CD Duplicator Creating an Image with Nero - continued 1. Add any data le by using the “Add” option or by dragging and dropping a le or les into the large white area. When nished adding les, click the “Next” button.
www .aleratec.com 36 Using the DVD/CD Duplicator 1. After the burn button is pressed, the “Save Image File” screen will appear . In the lowest dropdown menu called “Save as type:” select “ISO Image Files (.iso)”. Nero NRG les are not supported.
www .aleratec.com 37 Using the DVD/CD Duplicator Creating an Image with Nero - continued 1. The image process is successful when Nero displays this screen.
www .aleratec.com 38 Specications Supported Media T ypes • DVD-R/R W • DVD+R/R W (Single Layer) • DVD+R DL/DVD-R DL (Dual Layer) • CD-R • CD-R W Supported Formats • Most Industry Standa.
www .aleratec.com 39 Technical Support After reading this User Guide, if you need additional assistance with this product, please contact Aleratec T echnical Support. Our technical staff will be happy to assist you, but they may need your help to better assist you.
www .aleratec.com 40 Service and Support Aleratec, Inc., Limited Warranty This Limited W arranty covers defects encountered in the course of normal use of this product and does not apply to damage from improper use, abuse, accidents, unauthorized service, or inadequate packaging when shipping the product to Aleratec, Inc.
www .aleratec.com 41 Service and Support Please Note: This W arranty is valid only within the United States and Puerto Rico, and applies only to products that are new and unopened on the date of purchase.
www .aleratec.com 42 Service and Support To Obtain Warranty Service: Y ou must ship your product to the authorized dealer where your product was purchased within the one year warranty period and no later than thirty days after discovery of claimed defect, whichever occurs rst.
www .aleratec.com 43 Technical Support FAX Back Form Aleratec, Inc. Technical Support Fax Back Form Please record the following information to help expedite any warranty claim: Model No.
Document Number: 280118_280118EU _ENG_Rev . A Copyright © 2013 Specifications subject to change without notice . Aleratec , Inc . 9851 Owensmouth Avenue Chatsworth, CA 91311 U.
デバイスAleratec 280118の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Aleratec 280118をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAleratec 280118の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Aleratec 280118の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Aleratec 280118で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Aleratec 280118を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAleratec 280118の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Aleratec 280118に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAleratec 280118デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。