AccessメーカーPCI-IDI-XXの使用説明書/サービス説明書
ページ先へ移動 of 16
10623 Roselle Street, San Dieg o, CA 92 121 • (858) 550-9559 • FAX (858) 550-7322 contactus@ accesio.com • www.accesi o.com MODELS PCI-IDI-XX SERIES USER MANUAL File: mpci-idi-48.
Notice The information in this document is provided for reference only. ACCES does n ot assume any liability arising out of the application or use of the informat ion or products d escrib ed herein.
Warranty Prior to shipment, ACCES equipment is thoroughly insp ecte d and tested to applicable sp ecifi cations. However, should equipment failure occu r, ACCES assu res its custo mers that pr ompt service and su ppo rt will be available.
Table of Contents Chapter 1: Introduction ................................................................................................. 5 Table 1-1 : Model Versions ..................................................................................
Chapter 1: Introduction Features • Individually-Isolated AC/DC Inputs for up to Three 16-Bit Group s, 48 total. • Reverse Polarity protection • AC Filtering • Optical Isolation, Channel-to- Channel and Channel -to-Host PC. • Change-of-State detection (ce rtain mo dels).
MODEL No. of Bits Max Input Voltage Change-of State Interrupt Capability AC Filter 16A 16 31V No Yes 16AC 16 31V Yes Yes 32A 32 31V No Yes 32AC 32 31V Yes Yes 48A 48 31V No Yes 48AC 48 31V Yes Yes 16B.
Specification Digital Isolated Inputs Number of inputs: 16, 32, or 48 Type: Non-polarized, optically isolated from each other and from the com puter (CMOS c ompatib le) Voltage Range xxA: Logic Low: 0 to 1.
ADDRESS AND CONTROL LOGIC COMPUTER PCI BUS CHANGE-OF- ST A TE DETECT IS O L ATE D IN P U T 0 IS O L ATE D IN P U T 4 7 PCI BUS INTERF ACE I NPU TS 0-47 Vcc CURRENT LI M I TE R Vcc CURRENT LI M I TE R .
Chapter 2: Installation A printed Quick-Start Guide (QSG) is pa cked with the card for your convenience. If you’ve already performed the steps from the QSG, you may find this chapter to be redu ndant and may skip forward to begin developing your application.
Hardware Installation 1. Do not install card into the computer until the software has been fully installed. 2. Turn OFF computer power AND unplug AC power fro m the system. 3. Remove the computer cover. 4. Carefully install the card in an available 5V or 3.
Chapter 3: Option Selection Each channel has a jumper configurabl e filter option. 3.90 " 6.9 0" NO F IL T ER FIL TER FL T 0 FLT1 5 FLT1 6 FLT3 1 FLT3 2 FLT4 7 Figure 3-1: Option Selection Map Filter Response Switch Jumpers are use d to select input filtering on a channel-by-channel basis (see Figure 3 -1).
Chapter 4: Address Selection This card uses I/O addre sses offset from the base a ddress assigned by the PC I bus. T he address spaces are defined in the Programming se ction of this manual.
Chapter 5: Programming The base address is assigned by the computer system duri ng installation and will fall on an eight byt e boundary. The card’s read and write fun ctions are a s follows: Addres.
Write Base + 7: COS En able/Disable Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 IRQ Enable/ Disable N/A N/A N/A N/A N/A N/A N/A Manual PCI-IDI-XX Series 14.
Chapter 6: Connector Pin Assignments Isolated inputs are connected to the card via a 50-pin HEAD ER type connector. There are three connectors named PORT0, PORT 1, and PORT2. The table below describes PORT 0. PORT1 and PORT2 are identical pinouts. Pin 50 is located towa rd the Jumpers, while Pi n 1 is located near connection to Motherboard.
Customer Comments If you experience any problems with this manual or ju st want to give us some feedba ck, ple ase email us at: manuals@accesio.com. Please detail any errors you find and in clude your mailing address so that we can send you any manual updates.
デバイスAccess PCI-IDI-XXの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Access PCI-IDI-XXをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAccess PCI-IDI-XXの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Access PCI-IDI-XXの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Access PCI-IDI-XXで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Access PCI-IDI-XXを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAccess PCI-IDI-XXの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Access PCI-IDI-XXに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAccess PCI-IDI-XXデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
