EpsonメーカーNX510の使用説明書/サービス説明書
ページ先へ移動 of 36
Network Installation Guide Epson Stylus ® NX510 Series Network Guide_R1.fm Page 1 Wednesd ay, April 8, 2009 2:37 PM.
2 Before You Begin Before You Begin Make sure y ou installed ink cartridges and loaded paper as described on the Start Here sheet. Then follow the instructions in this guide to set up the print er for use on a network. Tip: For a video tutorial and other information about setting up a wireless network, go to: epson.
Choose Your Connection Type 3 Choose Your Connection Type Wireless T o connect the printer wirelessly , see page 4. Note: If you want to print wirelessly but do not have an access point or router , see “Create an Ad-Hoc Wireless Connection” on page 16.
4 Wireless Network Installation Wireless Network Installation T o add the printer to your wir eless networ k, you need to know the name (SSID) of your wireless network. If it has securi ty enabled, y ou also need to know the WEP key or WP A passphrase.
Wireless Ne twork Installa tion 5 3. P ress OK to select Wireless LAN Setup . 4. P ress OK to select Setup Wi zard . 5. P ress u or d to select the name of your wire less network, then press OK . If your network name isn ’ t listed, try the following: ■ Make sure that y our wireless r outer or access point is turned on and working correctly .
6 Wireless Network Installation 7. U se the arrow buttons on the printer’ s control panel to enter your WEP key or WP A passphrase. Press the x Menu button to switch between uppercase, lowercase, or numeric/special characters. Important : WP A passphrases and WEP keys in ASCII form at are case-sensitive.
Wireless Ne twork Installa tion 7 9. When you see a screen like this one, verify that the settings are correct. If you need to change a setting, press y Back until you see the setting you need to change. 10. Once you have verified th at your network settings are correct, press OK to save the settings and return to the N etwork Settings menu.
8 Wireless Network Installation Connect Wirelessly Using Advanced Setup U se this setup method if your access point or router isn ’ t broadcasting its network name (SSID). 1. P ress the F Setup button on the printer’ s control panel. 2. P ress l or r to select Network Settings , then press OK .
Wireless Ne twork Installa tion 9 5. P ress u or d to select Manual Setup , then press OK . 6. When you see this screen, press OK . 7. P ress u or d to select Infrastructure Mode , then press OK . 8. P ress u or d to select Enter SSID , then press OK .
10 Wireless Network Installation 9. U se the arro w buttons on the printe r’ s control panel to enter your wir eless network name (SSID). P ress the x Menu button to s witch between uppercase, lowercase, or numeric/special characters. Important : Network names are case-sensitive.
Wireless Ne twork Installa tion 11 11. P ress u or d to select the security mode that your wir eless network is using, then press OK . Note: If your wireless network doesn’t have security enabled, select None , then press OK .
12 Wireless Network Installation Select WPA Security Settings 1. U se the arro w buttons on the printe r’ s control panel to enter your WP A passphrase. P ress the x Menu button to switch between u ppercase, low ercase, or numeric/special characters.
Wireless Ne twork Installa tion 13 Select WEP Security Settings 1. P ress u or d to select Alphanumeric if your WEP key is ASCII, or select Hexadecimal if your WEP key is in hexadecimal format. Note: If the WEP key is 5 or 13 characters, it’ s ASCII.
14 Wireless Network Installation ■ Pre s s x Menu to switch between uppercase ( ABC ), lower case ( abc ), or numeric ( 123 ) characters. ■ Pre s s u or d until you se e the charact er you wa nt. ■ Pre s s l or r to move the cursor . ■ Pre s s – to delete a character .
Wireless Ne twork Installa tion 15 4. W ait for the printer to connect to your wireless network (this can take up to 90 seconds). Once it ’ s connected, you se e a green WiFi light on the printer’ s control panel. 5. Continue with “Install Softwar e ” on page 23.
16 Wireless Network Installation Create an Ad-Hoc Wireless Connection U se this setup method if you want to print wirelessly but do not have an access point or router . Important : For Windows ® users: If your computer is connected to a network with an Ethernet cable, you need to disconnect it before ins talling software .
Wireless Ne twork Installa tion 17 4. P ress u or d to select Advanced Setup , then press OK . 5. P ress u or d to select Manual Setup , then press OK . 6. When you see this screen, press OK . 7. P ress u or d to select Ad Hoc Mode , then press OK . 8.
18 Wireless Network Installation 9. U se the arro w buttons on the printe r’ s control panel to create a unique network name (SSID) to identify your printer . P ress the x Menu button to switch between uppe rcase, lo wercas e, or numeric/special characters.
Wireless Ne twork Installa tion 19 10. P ress OK to select the default channel for your Ad Hoc network. 11. Continue with the next section. Choose Security Settings 1. P ress u or d to select the security mode you want to use for the A d Hoc wireless network, then pr ess OK .
20 Wireless Network Installation 5. U se the arro w buttons on the p rinter ’ s control pane l to enter y our WEP key . P ress the x Menu button to switch between uppercase, lowercase, or numeric characters. Important : WEP keys in ASCII format are case-sensitive.
Wireless Ne twork Installa tion 21 Confirm Your Settings a nd Connect to the Network 1. When you see a screen like this one, verify that the settings are correct. If you need to change a setting, press y Back until you see the setting you need to change.
22 Wired (Ethern et) Instal lation Wired (Ethernet) Installation 1. Connect an Ethernet network cable to the LAN (10/10 0) po r t o n y ou r p r i nt e r .
Install Software 23 Install Software F ollow the steps in this section for each computer you want to use with your printer over the network. 1. Insert the printer software CD. 2. Windows Vista ® : I f you see the A utoPlay window , click Run SETUP.EXE .
24 Install Software 5. When you see this screen, click Next to start network setup. 6. Make sur e that your printer is turned on and connected to y our network. 7. When you see the F irewall W arning screen, click Next . Note: If you see a firewall alert message, click Unblock or Allow to let EpsonNet Setup continue.
Install Software 25 8. W ait while E psonN et Setup configures your printer for the network. 9. Do one of the following: ■ If you see the Installation Complete screen, continue with “F inish the Installation ” on page 28.
26 Install Software ■ If no available printers ar e found on your network, see “EpsonN et Setup was unable to find my printe r on the network ” on page 32. ■ If EpsonN et Setup finds more than on e printer on y our network, select the printer you want to configur e, then click Next .
Install Software 27 ■ If you are installing the printer in Ad H oc mode and you see this screen, make sure that your computer ’ s wirele ss adapter is set to acquire an IP address automatically . Then select Acquire the IP Addre ss Automatically using DHCP ( Recommended ) and click Next .
28 Finish the I nstallatio n Finish the Installation F ollow the steps for your operating system: ■ “W in do ws ” b el ow ■ “Macintosh ” on page 29 Windows 1. P r int a test page, then click Finish . 2. F ollow the prompts on the screen to install bonus software and finish the installation.
Finish the Installati on 29 Macintosh 1. Click Save to install an application that allows you to access the printer ’ s memor y card slots o ver the network. 2. Select where you would like in stall the application, then click Save . 3. Click Finish .
30 Finish the I nstallatio n 4. When you see this screen, click Add Printer . 5. F ollow the steps on the right side of the screen to add your EPSON TCPIP printer . Note: It may take up to 90 seconds for your computer to find the EPSO N TCPIP printer on the network.
Troubleshootin g 31 Troubleshooting If you have problems setting up or usin g your product on a network, check these sections for help: ■ “Setup P roblems ” below ■ “P rinting Problems ” on page 33 ■ “Scanning P roblems ” on page 34 This section also explains how to print a N etwork S tatus Sheet (see page 34).
32 Troubleshooting EpsonNet Setup was unable to find my printe r on the network 1. If you see a screen like this one, do one of the following: ■ If you connected the printer wirelessly , verify that the printer is turned on and the green WiF i l ight on the printer’ s control panel is on.
Troubleshootin g 33 Software insta llation fail ed Make sur e that the printer is connected to y our network ( see page 4 for wireless or page 22 for Ethernet).
34 Troubleshooting Printing is slow or the print is cut off F or wireless connections, print a N etwork S tatus Sheet (see below) and check the Signal S trength. If it’ s poor , tr y moving the printer closer to your wireless router or access point.
Copyright Noti ce 35 Copyright Notice All rights reserve d. No part of this publicatio n may be reproduce d, stored in a retrieval sy stem, or transmitted in any fo rm or by any means, elec tronic , mechanical, photocopying, recording, or otherwise, without the pr ior written permission of Seiko Epson Corporat ion.
CPD-27300R1 Printed in XXXXXX Network Guide_R1.fm Page 36 Wedn esday, April 8, 2009 2:3 7 PM.
デバイスEpson NX510の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Epson NX510をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEpson NX510の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Epson NX510の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Epson NX510で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Epson NX510を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEpson NX510の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Epson NX510に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEpson NX510デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
