ExmarkメーカーOCDWB01の使用説明書/サービス説明書
ページ先へ移動 of 20
OCDWB01 OPERA TOR CONTROLLED DISCHARGE FOR W ALK-BEHIND UNITS Part No. 4500-569 Rev . A.
Exmark reser ves the right to make changes or add improv ements to its products at an y time without incurring any obligation to make such changes to products man ufactured previousl y .
Introduction CONGRATULATIONS on the purchase of your Exmark equipment. This product has been carefully designed and man ufactured to gi ve y ou a maxim um amount of dependability and years of trouble-free operation. This man ual contains operating, maintenance , adjustment, and safety instr uctions for y our Exmark equipment.
Contents Introduction . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 3 Safety . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . .
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 1) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 1 1.
Safety collection system or m ulch kit in place and w orking properly . • Stop engine, wait for all mo ving parts to stop , remov e key and engag e parking brake: – Before c hecking, cleaning or w orking on the mow er .
Safety Safety and Instructional Decals • Keep all safety signs legible . R emo ve all grease, dirt and debris from safety signs and instr uctional labels . • R eplace all w orn, damag ed, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components .
Setup Setup Assembling Discharge Deector to OCDWB01 Insert the rod through the rst tab on the gate link frame, disc harge deector , and second tab on the gate link frame (Figure 2). Orient and install the spring so that the loop will rest in the notch on the disc harge deector .
Setup Figure 5 1. Latch 3. Front pin 2. OCDWB01 assembly 4. Slot • If the front pin does not engag e in the slot in the deck, loosen or completely remov e the hardware in the g ate link frame as shown in Figure 6. P osition the g ate link frame so that the front pin aligns with the slot.
Setup there will be room to tighten the n ut on the upper hole, on the underside of the front panel. C. Drill tw o 11/32 inc h diameter holes on the front panel as sho wn in Figure 7. D . Align the tw o holes in the mounting brack et with the front panel of the unit.
Setup B . Align the existing hole at the rear of the unit with the right hole on the brac ket. C. P osition the brac ket horizontally or with the narrow end pointed slightly downw ard. D . Using the mounting brac ket as a template , mark the left hole location onto the side panel of the unit and drill 11/32 inc h diameter hole (see Figure 11).
Product Overview Figure 14 1. V elcro strap 2. Loom clip Product Overview Figure 15 1. Handle 2. Discharge gate (under discharge deector) 3. Discharge deector 12.
Operation Operation Use the discharge gate to temporarily stop or deect g rass clippings aw ay from sidew alks , parking lots , patios , or anywhere grass clippings are not desired to be discharged. The handle allo ws the discharge gate to be held in any position from fully closed to fully open.
Operation Closing the Discharge Gate F or all W alk-Behind Units ex cept V antage: Push down on the handle to close the gate. Figure 18 1. Push down 2. Handle in gate closed position F or V anta ge Units: Push forw ard on the handle to close the gate.
Operation Figure 21 1. Handle assembly 3. Clevis pin 2. Mounting bracket 4. Hairpin 4. Unloc k the assembly and pi v ot it aw ay from the mow er deck. Lift the OCD WB01 out of the dec k mounting tube .
Maintenance Maintenance Note: Deter mine the left and right sides of the machine from the normal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders.
Maintenance Figure 22 1. Pivot bolt and nut Discharge Gate Adjustment The disc harge gate is properly adjusted in the closed position when the discharge gate is at ag ainst the discharge opening . If the disc harge gate does not close at follo w the steps below: 1.
T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. The following table lists some of the common causes of trouble . If assistance is needed, contact y our Exmark Ser vice Dealer .
Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we .
MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM.
デバイスExmark OCDWB01の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Exmark OCDWB01をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはExmark OCDWB01の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Exmark OCDWB01の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Exmark OCDWB01で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Exmark OCDWB01を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はExmark OCDWB01の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Exmark OCDWB01に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちExmark OCDWB01デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
