FishmanメーカーJerry Douglas Signature Seriesの使用説明書/サービス説明書
ページ先へ移動 of 20
USER GUIDE JERR Y DOUGLAS SIGNA TURE SERIES A URA ® IMAGING PEDAL.
2 Quick start Power – Install a 9V alkaline or lithium battery (not included). Set the controls – V olume at minimum, select at #1 and blend at its mid-point. Plug in – Use standard ¼-inch shielded instrument cables. Place any other pedals after the Aura.
3 ® ACOUSTIC IMAGING.
4 About this pedal Larry Fishman developed the Signature Series Aura Pedal with a world-class team of professionals, including musician Jerry Douglas, r ecording studio engi- neer Bil V ornDick, and reknowned r esonator builder Paul Beard, to bring you the most realistic amplifi ed tone available.
5 A word from Paul Beard “In the world of resophonic guitar amplifi cation, we fi nally have resolution! The Fishman Nashville Series resophonic pickup is the r esult of new technology and innovative design. Use this pickup when playing with the Aura Imaging Pedal, select a microphone Image and turn it up.
6 Images Image Microphone T ype Distance 1 Neumann U67 Large diaphragm tube condensor 12” 2 Neumann U67 Large diaphragm tube condensor 18” 3 RCA 77 Poly-directional ribbon 12” 4 RCA 77 Poly-dire.
7 Image Microphone T ype Distance 9 Royer R-121 Figure 8 Ribbon 12” (Instrument drop tuned to CAFCAF) 10 Neumann U47 Lg. diaphragm cardioid tube condensor 12” 11 Neumann FET 47 Cardioid FET Lg. diaphragm condensor 12” 12 Neumann FET 47 Cardioid FET Lg.
8 Using effects When using your Aura Imaging Pedal with other effects devices, place the Aura Imaging Pedal fi rst in the chain after your guitar . ® ACOUSTIC IMAGING.
9 If you have a pedal tuner , place it before the Aura Imaging Pedal. ® ACOUSTIC IMAGING.
10 Left side panel Output Use a standard ¼-inch instrument cable to connect the output to your amplifi er , mixer or effects devices. Y ou can also connect this output to an unbalanced input on a recor ding system.
11 Right side panel Input Plug in your guitar here with a standar d ¼-inch instrument cable. If you have a passive undersaddle pickup (no battery onboard), always plug into the Aura Imaging Pedal fi rst, even if you use a pedal tuner . Tr i m Raise or lower the trim to optimize the input level for your pickup.
12 Control set Phase switch Use the phase switch to improve bass r esponse at low volume or to control feedback at high volume. Play your guitar and toggle the phase switch back and forth until you achieve the desired r esult. V olume For the cleanest signal, set the volume as high as possible without clipping the next device in the signal chain.
13 Select The 16 Images you can choose with the select knob are hand picked for your type of guitar . T ry all 16 and pick the ones that compliment your playing style and sound good in the room. For example, dark/deep sounding Images may add impact to a solo performance.
14 Blend (continued) Suggestions • T o fi nd a good mix of Image and pickup, turn the blend knob to about 8 o’clock, then step on the footswitch. Compare the Image/ pickup mix to the dry pickup signal. Slowly move blend clockwise and then switch between the two until you are happy with the Image/pickup blend.
15 F ootswitch Step on the footswitch to bypass the Aura effect. When you stomp, you’ll hear the dramatic differ ence between the Image blend and the dry pickup. When the light above the footswitch is on, the Image is active. Note when the effect is bypassed, your guitar signal remains buf fered.
16 Power Power may be supplied by either a 9V battery ( battery compartment under pedal ) or an approved 9V adapter . Insert a plug into the input jack, and the Aura Imaging Pedal powers up. T o conserve the battery , r emove the plug fr om the input when not in use.
17 Battery replacement The clip/batt indicator will light steadily when it is time to change the battery . Open the battery door underneath the pedal and install a fresh 9V alkaline or lithium battery . When the clip/batt LED comes on you have approximately one hour of remaining battery life.
18 Specifi cations Digital signal path: A/D, D/A conversion: 24-bit Signal processing: 32-bit Power supply: 9V alkaline battery or 9VDC adapter T ypical in-use curr ent consumption: 18mA T ypical 9V .
19.
www .fi shman.com 513-300-146 Rev A 6-07.
デバイスFishman Jerry Douglas Signature Seriesの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Fishman Jerry Douglas Signature Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFishman Jerry Douglas Signature Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fishman Jerry Douglas Signature Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fishman Jerry Douglas Signature Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fishman Jerry Douglas Signature Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFishman Jerry Douglas Signature Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fishman Jerry Douglas Signature Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFishman Jerry Douglas Signature Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。