FriedrichメーカーRT5の使用説明書/サービス説明書
ページ先へ移動 of 14
1 Heat /1 Cool Manual Ch angeover Bat ter y or Har dwire d RT5 Non-Programmable Electronic Thermostat Installation, Operation & Application Guide • For use with Friedrich PT AC units ONL Y • B.
T able of Contents Parts Diagram............................................................................................................................................... 1 Speci fi cations .......................................................
1 P arts Diagram.
2 Electrical rating: • 24 V AC (18-30 V AC) • DC Power: 3.0 VDC (2 “AA” batteries included) • 1 amp maximum per terminal • 3 amp maximum total load T emperature control range: 45°F to 90°F (7°C to 32°C) Accuracy: ± 1°F (± 0.
3 ELECTRICAL SHOCK HAZARD – T urn off power at the main service panel by removing the fuse or switching the appropriate circuit breaker to the OFF position before removing the existing thermostat. 1. Turn of f power to the heating and cooling system by removing the fuse or switching the appropriate circuit breaker off.
4 T o Install Thermostat (continued) 2. T o remove cover, insert and twist a coin or screwdriver in the slots on the sides of the thermostat. 3. Put thermostat base against the wall where you plan to mount it (Be sure wires will feed through the wire opening in the base of the thermostat).
5 HARDWIRED C R W Y B GL GH C RH RC W Y B O GL GH PRE-INST ALLED JUMPER T H E R M O S T A T F R I E D R I C H P T A C.
6 The con fi guration mode is used to set the RT5 to match your heating/cooling system. The RT5 functions with Friedrich PT AC models. Ensure that the thermostat is con fi gured for air conditioning with ELECTRIC HEA T ONL Y . T o con fi gure the R T5, perform the following steps: 1.
7 FIL TER DIFF ROOM SET REMOTE 3. Temperature Differential (1°F to 3°F) (0.5°C to 1.5°C) – Set the number of degrees between your “setpoint” temperature and your “turn on” temperature. Press the or button to set differential value. Press the SW6 button to advance to the next screen.
8 FIL TER DIFF ROOM SET REMOTE 6. Room temperature offset (+9°F to -9°F) (+4.5°C to -4.5°C) Adjust to calibrate displayed room temperature to match actual room temperature. Note: When not set to 0, ROOM will display Press the or button to select. Press the SW6 button to advance to the next screen.
9 Once the thermostat is installed, it should be thoroughly tested. caution! : Do not energize the air conditioning system when the outdoor temperature is below 50 degrees. It can result in equipment damage or personal injury . Cool T est 1. Slide Mode switch to Cool mode.
10 Fan T est 1. Slide Fan switch to On position. 2. Indoor fan turns on. Auto On Auto On 3. Slide Fan switch to Auto position. 4. Indoor fan turns off. (T esting the thermostat continued from Page 9) The RT5 is a single-stage heat, single-stage cool thermostat.
11 Symptom Remedy No display For Hardwired Installation Check for 24 V AC at thermostat; display is blank when 24 V AC is not present For Battery Installation Display is blank when batteries are drain.
Friedr ich Air C onditioning Co. Post O f fice B ox 1 540 • S an Antonio, T ex as 782 95 - 1 54 0 42 00 N. Pan A m E xpre ss way • San Antonio, T ex as 782 1 8-52 1 2 (2 1 0) 35 7-4 4 0 0 • FA X (2 1 0) 3 57 - 4 4 80 w w w .
デバイスFriedrich RT5の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Friedrich RT5をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFriedrich RT5の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Friedrich RT5の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Friedrich RT5で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Friedrich RT5を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFriedrich RT5の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Friedrich RT5に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFriedrich RT5デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。