FujitsuメーカーMPA3035ATの使用説明書/サービス説明書
ページ先へ移動 of 176
C141-E034-02EN MPA3017AT MPA3026AT MPA3035AT MPA3043AT MPA3052AT DISK DRIVES PRODUCT MANUAL.
C141-E034-02EN i REVISION RECORD Edition Date published Revised contents 01 Jan., 1997 02 August, 1997 Specification No.: C141-E034-**EN The content s of t his manual is s ubject to c hange without prior notice.
C141-E034-02EN iii PREFACE This m anu al descri bes the MPA 3017AT/MPA3026A T/MPA3035A T/MPA3043A T/MPA3052A T, a 3.5-inch hard disk drive with a BUILT-IN controller that is compatible with the ATA interface. This manual explains, in detail, how to incorporate the hard disk drives into user systems.
iv C141-E034-02EN Conventions for Alert Messages This manual uses the following conventions to show the alert m essages. An alert message consists of an alert sign al and alert statements. The alert sign al consists of an alert sy mbol an d a signal w ord or just a signal word.
C141-E034-02EN v LIABILITY EXCEPTION "Disk drive defects" refers to defects that involve adjustment, repair, or replacement. Fujit su is n ot liable for an y oth er disk dri ve defects, s uc.
C141-E034-02EN vii CONTENTS page CHAPTER 1 DEVICE OVERVIEW ......................................................................................... 1 - 1 1.1 Features....................................................................................
C141-E034-02EN viii 3.4.1 Location of setting jumpers ............................................................................................... ... 3 - 9 3.4.2 Factory default setting .............................................................
C141-E034-02EN ix 5.2.2 Command block registers ................................................................................................... .. 5 - 8 5.2.3 Control block registers ................................................................
C141-E034-02EN x 6.3.1 Power save mode ........................................................................................................... ....... 6 - 8 6.3.2 Power commands .....................................................................
C141-E034-02EN xi FIGURES page 1.1 Current fluctuation (Typ.) at +5V when power is turned on ................................................. 1 - 7 2.1 Disk drive outerview .............................................................................
C141-E034-02EN xii 5.4 Protocol for command abort ................................................................................................. 5 - 57 5.5 WRITE SECTOR(S) command protocol............................................................
C141-E034-02EN xiii TABLES page 1.1 Specifications.............................................................................................................. .......... 1 - 4 1.2 Model names and product numbers .....................................
C141-E034-02EN 1 - 1 CHAPTER 1 DEVICE OVER VIEW 1.1 Features 1.2 Device Specifications 1.3 Power Requirements 1.4 Environmental Specifications 1.5 Acoustic Noise 1.6 Shock and Vibration 1.7 Reliability 1.8 Error Rate 1.9 Media Defects Overview and f eatures are described in this chapter, and specifications and power requiremen t are described.
C141-E034-02EN 1 - 2 (4) Average positioning time Use of a rotary voice coil motor in the head positioning mechanism greatly increases the positioning speed.
C141-E034-02EN 1 - 3 (5) Error correction and retry by ECC If a recoverable error occu rs, the disk drive itself attem pts error recovery . The 18-byte ECC has improved buffer error correction for correctable data errors.
C141-E034-02EN 1 - 4 1.2 Device Specifications 1.2.1 Specifications summary Table 1.1 shows the specifications of the disk drive. Table 1.1 Specifications MPA3017AT MPA3026AT MPA3035AT MPA3043AT MPA3052AT Formatted Capacity (*1) 1750.00 MB 2625.00 MB 3500.
C141-E034-02EN 1 - 5 1.2.2 Model and product number Table 1.2 lists the model names and product numbers. Table 1.2 Model names and product numbers Model Name Capacity (user area) Mounting Screw Order No. Others MPA3017AT 1749.56 MB No. 6-32UNC CA01602-B321 MPA3026AT 2624.
C141-E034-02EN 1 - 6 (3) Current Requirements and Power Dissipation Table 1.3 lists the current and power dissipation. Table 1.3 Current and power dissipation Typical RMS current (*1) +12 V +5 V Model MPA 3017AT MPA 3026AT MPA 3035AT MPA 3043AT MPA 3052AT All Models MPA 3017AT MPA 3026AT MPA 3035AT MPA 3043AT MPA 3052AT Spin up 1.
C141-E034-02EN 1 - 7 (4) Current fluctuation (Typ.) at +5V when power is turned on Note: Maximum current is 1.5 A and is continuance is 1.5 seconds Figure 1.1 Current fluctuation (Typ.) at +5V when power is turned on (5) Power on/off sequence The voltage detector circuit m onitors +5 V and +12 V.
C141-E034-02EN 1 - 8 1.4 Environmental Specifications Table 1.4 lists the environmental specifications. Table 1.4 Environmental specifications Temperature • Operating • Non-operating • Thermal G.
C141-E034-02EN 1 - 9 1.6 Shock and Vibration Table 1.6 lists the shock and vibration specification. Table 1.6 Shock and vibration specification Vibration (swept sine, one octave per minute) • Operating • Non-operating 5 to 300 Hz, 0.
C141-E034-02EN 1 - 10 (4) Data assurance in the event of power failure Except for the data blo ck b eing written to, the data on the disk media is assured in the event o f any power supply abnormalities.
C141-E034-02EN 2 - 1 CHAPTER 2 DEVICE CONFIGURA TION 2.1 Device Configuration 2.2 System Configuration 2.1 Device Configuration Figure 2.1 show s the disk drive. The disk drive con sists of a disk enclosu re (DE), read/write preamplif ier, and controller PCA.
C141-E034-02EN 2 - 2 (1) Disk The outer diam eter of t he disk is 95 mm . The in ner diam eter is 25 m m. The nu mber of disks used varies w ith t he model , as described below .
C141-E034-02EN 2 - 3 Spindl e 0 1 Actu ator MPA3017 Model MPA3026AT Model Spindl e 1 2 0 Actu ator MPA3043AT Model Spindl e 2 3 4 0 1 Actu ator MPA3035AT Model Spindl e 1 3 2 0 Actu ator MPA3052AT Model Spindl e 2 3 5 4 0 1 Actu ator Figure 2.
C141-E034-02EN 2 - 4 (5) Air circulation system The disk enclosure (DE) is sealed to prevent du st and dirt from en tering. The disk enclosu re featu res a cl osed loop air circulation sy stem t hat relies on the blow er eff ect of th e rotating disk.
C141-E034-02EN 2 - 5 2.2.3 2 drives connection ATA interfac e AT bus (H ost inte rfac e) Disk d r i ve #1 Disk d r i ve #0 HA (H ost ad apto r) Hos t Note: When the drive that is not conformed to ATA is connected to the disk drive is ab ove configuration, the operation is not guaranteed.
C141-E034-02EN 3 - 1 CHAPTER 3 INST ALLA TION CONDITIO NS 3.1 Dimensions 3.2 Mounting 3.3 Cable Connections 3.4 Jumper Settings 3.1 Dimensions Figure 3.1 illustrates the d imensions of the disk drive and positio ns of the mounting screw holes. All dimensions are in mm.
C141-E034-02EN 3 - 2 Figure 3.1 Dimensions.
C141-E034-02EN 3 - 3 3.2 Mounting (1) Orientation Figure 3.2 illustrates the allowable orientations for the disk drive. T he mounting angle can vary ±5° from the horizontal. (a) Horizontal mounting (b) Vertical mounting –1 (c) Vertical mounting –2 Figure 3.
C141-E034-02EN 3 - 4 Figure 3.3 Limitation of side-mounting Figure 3.4 Mounting frame structure 5.0 or less 4.5 or less 2 B Frame of system cabinet Details of B Details of A Frame of system cabinet Screw Screw PCA DE 2.
C141-E034-02EN 3 - 5 (4) Ambient temperature The temperature conditio ns for a disk drive mounted in a cab inet ref er to the ambient temperature at a poin t 3 cm from the disk drive. Pay attention to the air f low to prevent the DE surf ace temperature from exceeding 60°C.
C141-E034-02EN 3 - 6 (5) Service area Figure 3.6 shows how the drive must be accessed (service areas) during and after installation. Figure 3.6 Service area (6) External magnetic fields Avoid m ounting the disk drive near strong magn etic sources such as loud speakers.
C141-E034-02EN 3 - 7 3.3 Cable Connections 3.3.1 Device connector The disk drive has the con nectors and termin als listed below f or connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. • Power supply connector (CN1) • ATA interface connector (CN1) Figure 3.
C141-E034-02EN 3 - 8 3.3.2 Cable connector specifications Table 3.2 lists the recommended specifications for the cable connectors. Table 3.2 Cable connector specifications Name Model Manufacturer Cabl.
C141-E034-02EN 3 - 9 3.3.4 Power supply connector (CN1) Figure 3.9 shows the pin assignment of the power supply connector (CN1). (View e d from cab le side) 4 3 2 1 +5VDC +5V R ETUR N +12V R ET UR N +12 VDC 4 3 2 1 Figure 3.9 Power supply connector pins (CN1) 3.
C141-E034-02EN 3 - 10 3.4.2 Factory default setting Figure 3.11 shows the default setting position at the factory. C04 A01 A02 C01 A39 A40 05 06 B01 B02 Figure 3.11 Factory default setting 3.4.3 Jumper configuration (1) Device type Master device (device #0) or slave device (device #1) is selected.
C141-E034-02EN 3 - 11 06 B02 CS EL c o nn ec ted to th e interf ace Ca ble s el ect i on can be don e b y th e spe c ial interfac e cab le. B01 0 5 Figure 3.13 Jumper setting of Cable Select Figures 3.14 and 3.15 show examples of cable selection using unique interface cables.
C141-E034-02EN 3 - 12 (3) Special setting 1 (SP1) The number of cylinders reported by the IDENTIFY DEVICE command is selected. (a) Default mode 2 4 6 1 3 5 2 4 6 Sl a ve Devi ce Mast er Device 1 3 5 2 4 6 1 3 5 Ca ble S el ect Model No.
C141-E034-02EN 4 - 1 CHAPTER 4 THEOR Y OF DEVICE OPERA TION 4.1 Outline 4.2 Subassemblies 4.3 Circuit Configuration 4.4 Power-on sequence 4.5 Self-calibration 4.6 Read/Write circuit 4.7 Servo Control This chapter ex plains basic design con cepts of the disk driv e.
C141-E034-02EN 4 - 2 4.2.2 Head Figu re 4.1 show s the read/ writ e head stru ctures. The MPA 3017AT has 2 read/w rite h eads, the MPA3026A T has 3, MPA3035A T has 4, MPA 3043AT has 5, an d MPA3052AT has 6. T hese heads are raised from the disk surface as the spindle motor approaches the rated rotation speed.
C141-E034-02EN 4 - 3 4.2.3 Spindle The spindle con sists of a disk stack assembly and spindle m otor. T he disk stack assem bly is activated by the direct dri ve sens or-less DC spindle m otor, w hich h as a speed of 5,400 rpm ±0.
C141-E034-02EN 4 - 4 4.3 Circuit Configuration Figure 4.2 shows the disk drive circuit configuration. (1) Read/write circuit The read/write circuit consists of tw o LSIs; read/write preamplifier (PreAMP) and read channel (RDC).
C141-E034-02EN 4 - 5 Figure 4.2 MPA30xxAT Block diagram.
C141-E034-02EN 4 - 6 4.4 Power-on Sequence Figure 4.3 describ es the operation seq uence of the disk drive at power-on. The outline is describ ed below. a) Af ter the pow er is turned on, th e disk drive executes th e MPU bus test, internal register read/write test, and w ork RAM read/write test.
C141-E034-02EN 4 - 7 c) b) a) R ele ase heads f rom actu ato r loc k Co nfirming spindle mo to r speed Self-di a g n osis 2 • Data b uf f er w rite/read te st The sp indle mo to r starts.
C141-E034-02EN 4 - 8 4.5 Self-calibration The disk drive occasionally perform s self-calibration in order to sense and calibrate mech anical external f orces on the actuator, and VCM torqu e.
C141-E034-02EN 4 - 9 4.5.2 Execution timing of self-calibration Self-calibration is executed when: • The power is turned on. • The disk drive receives the RECALIBRATE command from the host. • The self-calibration execution timechart of the disk drive specifies self-calibration.
C141-E034-02EN 4 - 10 4.6 Read/write Circuit The read/write circuit consists of the read/w rite preamplifier (PreAMP), the write circuit, the read circuit, and the tim e base generator in the read chann el (RDC). Figure 4.4 is a block diagram of the read/write circuit.
C141-E034-02EN 4 - 11 Figure 4.4 Read/write circuit block diagram.
C141-E034-02EN 4 - 12 4.6.3 Read circuit The head read signal f rom the PreAMP is regu lated by th e automatic g ain control (AGC ) circuit. Then the output is converted into the sampled read data pulse by the programmable filter circuit and the adaptive equ alizer circuit.
C141-E034-02EN 4 - 13 Figure 4.6 PR4 signal transfer.
C141-E034-02EN 4 - 14 (4) Viterbi detection circuit The sample hold waveform output from the adaptive equalizer circuit is sent to the Viterb i detection circuit. The Viterbi detection circu it demodulates data according to the survivor path sequence.
C141-E034-02EN 4 - 15 Table 4.3 Write clock frequency and transfer rate of each zone Zone 0 1 2 34567 Cylinder 0 to 622 623 to 1788 1789 to 2217 2218 to 2618 2619 to 3030 3031 to 3827 3828 to 4141 4142 to 4808 Transfer rate [MB/s] 14.964 14.111 13.787 13.
C141-E034-02EN 4 - 16 4.7.1 Servo control circuit Figure 4.7 is the block d iagram of the servo contro l circuit. The following describes the functions of the blocks: (5) (1) (2) (3) (4) P.
C141-E034-02EN 4 - 17 c. Seek to specified cylinder Drives the VCM to position the head to the specified cylinder. d. Calibration Senses and stores th e thermal of fset betw een heads and th e mechan ical forces on the actu ator, and stores the calibration value.
C141-E034-02EN 4 - 18 (2) Servo burst capture circuit The four servo signals can be sy nchronously detected by the STROB signal, full-wave rectified integrated. (3) A/D converter (ADC) The A/D converter (A DC) receives the servo sig nals are integrated, converts them to digital, and transfers the digital signal to the DSP unit.
C141-E034-02EN 4 - 19 4.7.2 Data-surface servo format Figure 4.8 describes the phy sical lay out of the servo f rame. The three areas in dicated by (1) to (3) in Figure 4.
C141-E034-02EN 4 - 20 (1) Write/read recovery This area is used to absorb the write/read transient and to stabilize the AGC. (2) Servo mark This area generates a timing for demodulating the gray code and po sition-demodulating the servo A to D by detecting the servo mark.
C141-E034-02EN 4 - 21 d) If the head is stopped at the reference cylinder from there. Track following control starts. (2) Seek operation Upon a data read/w rite request from the host, the MPU conf irms the n ecessity of access to the disk. If a read or instruction is issued, the MPU seeks the desired track.
C141-E034-02EN 4 - 22 e) The MPU is waiting for a PHASE signal. When no phase signal is sent for a specif ic period, the MPU resets the SVC and starts from the beginni ng. When a PHASE sign al is sent, the SVC enters the acceleration mode. (2) Acceleration mode In this mode, the MPU stops to send the phase switching signal to the SVC.
C141-E034-02EN 5 - 1 CHAPTER 5 INTERF ACE 5.1 Physical Interface 5.2 Logical Interface 5.3 Host Commands 5.4 Command Protocol 5.5 Ultra DMA Feature Set 5.
C141-E034-02EN 5 - 2 5.1 Physical Interface 5.1.1 Interface signals Figure 5.1 shows the interface signals. IN TRQ : IN TER RU PT R EQ U EST IOCS16-: IOCS 16 PDIAG- : PASSE D DI AGNOST I C IORDY : I/ .
C141-E034-02EN 5 - 3 5.1.2 Signal assignment on the connector Table 5.1 shows the signal assignment on the interface connector. Table 5.1 Signal assignment on the interface connector Pin No.
C141-E034-02EN 5 - 4 [signal] [I/O] [Description] IOR–, HDMARDY–, HSTROBE I IOR– is the strobe signal asserted by the host to read device registers or the data port.
C141-E034-02EN 5 - 5 [signal] [I/O] [Description] IORDY, DDMARDY–, DSTROBE O This signal is negated to extend the host transfer cycle of any host register access (Read or Write) when the device is not ready to respond to a data transfer request. DDMARDY– is a flow control signal for Ultra DMA data out bursts.
C141-E034-02EN 5 - 6 5.2 Logical Interface The device can operate for comm and execution in either address-specif ied mode; cy linder-h ead- sector (C HS) or L ogical block addres s (LBA ) mode. The IDENTIFY DEVICE i nform ation indicates w hether th e device supports the LBA mode.
C141-E034-02EN 5 - 7 Table 5.2 I/O registers I/O registers Read operation Write operation Command block registers 10000 Data Data X'1F0' 10001 Error Register Features X'1F1' 10010 .
C141-E034-02EN 5 - 8 5.2.2 Command block registers (1) Data register (X'1F0') The Data register is a 16-bit regi ster for data block transfer betw een the device and the host system.
C141-E034-02EN 5 - 9 [Diagnostic code] X'01': No Error Detected. X'02': HDC Register Compare Error X'03': Data Buffer Compare Error. X'05': ROM Sum Check Error. X'80': Device 1 (slave device) Failed. Error register of the master device is valid under two devices (master and slave) configuration.
C141-E034-02EN 5 - 10 (6) Cylinder Low register (X'1F4') The contents of th is register indicates low -order 8 bits of th e starting cy linder address for any disk- access. At the end of a command, the contents of this register are updated to the current cylinder number.
C141-E034-02EN 5 - 11 (9) Status register (X'1F7') The contents of this reg ister indicate the status of the device. T he contents of this register are updated at the com pletion of each com m and. When the BSY bit is cleared, other bits in this regist er should be v alidated w ithin 400 ns.
C141-E034-02EN 5 - 12 - Bit 3: Data Request (DRQ) bit. This bit indicates that th e device is ready to tran sfer data of word unit or byte unit between the host system and the device. - Bit 1: Always 0. - Bit 0: Error (ERR) bit. This bit indicates that an error was detected w hile the previou s comm and was being executed.
C141-E034-02EN 5 - 13 5.2.3 Control block registers (1) Alternate Status register (X'3F6') The Alternate Status reg ister contains the sam e information as the Status register of the comm and block register.
C141-E034-02EN 5 - 14 5.3.1 Command code and parameters Table 5.3 lists t he supporte d comm ands, com m and code and th e registers th at needed parameters are written.
C141-E034-02EN 5 - 15 Table 5.3 Command code and parameters (2 of 2) Command code (Bit) Parameters used 765432 10 F R S C S N C Y D H STANDBY IMMEDIATE 1 1 0 1 0 1 1 0 0 0 1 0 0 0 0 0 NNNN D SLEEP 1 1.
C141-E034-02EN 5 - 16 5.3.2 Command descriptions The contents of th e I/O registers to be necessary for issuing a comm and and the example indication of the I/O registers at command completion are shown as following in this subsection.
C141-E034-02EN 5 - 17 Note: 1. When the L bit is specified to 1, the lower 4 bits of the DH register and all bits o f the CH, CL and SN reg isters indicate the LBA bits (bits of the DH register are the MSB (most significant bit) and bits of the SN register are the LSB (least significant bit).
C141-E034-02EN 5 - 18 At command completion (I/O registers contents to be read) 1F7 H (ST) Status information 1F6 H (DH) × L × D V End head No. /LBA [MSB] 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (ER) End cylinder No. [MSB] / LBA End cylinder No.
C141-E034-02EN 5 - 19 Figure 5.2 shows an example of the execution of the READ MULTIPLE command. • Block cou nt specif ied by SET MULTIPLE MODE com m and = 4 (num ber of sectors in a block) • READ.
C141-E034-02EN 5 - 20 Note: If the comm and is terminated due to an error, the remaining number of secto rs for wh ich d ata was not transferred is set in this register. (3) READ DMA (X'C8' or X'C9') This command operates similarly to the READ SECTOR(S) command except for following events.
C141-E034-02EN 5 - 21 At command completion (I/O registers contents to be read) 1F7 H (ST) Status information 1F6 H (DH) × L × D V End head No. /LBA [MSB] 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (ER) End cylinder No. [MSB] / LBA End cylinder No.
C141-E034-02EN 5 - 22 At command completion (I/O registers contents to be read) 1F7 H (ST) Status information 1F6 H (DH) × L × D V End head No. /LBA [MSB] 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (ER) End cylinder No. [MSB] / LBA End cylinder No.
C141-E034-02EN 5 - 23 At command completion (I/O registers contents to be read) 1F7 H (ST) Status information 1F6 H (DH) × L × D V End head No. /LBA [MSB] 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (ER) End cylinder No. [MSB] / LBA End cylinder No.
C141-E034-02EN 5 - 24 The contents of th e comm and block registers related to addresses af ter the transfer of a data block containin g an erred sector are undefin ed. To obtain a valid error inf ormation, th e host should retry data transfer as an individual requests.
C141-E034-02EN 5 - 25 1) Single word DMA transfer mode 2: Sets the FR register = X'03' and SC register = X'12' by the SET FEATURES command 2) Multiword DMA transfer mode 2: Sets th.
C141-E034-02EN 5 - 26 At command issuance (I/O registers setting contents) 1F7 H (CM) 00111100 1F6 H (DH) × L × D V Start head No. /L BA [MSB] 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (FR) Start cylinder No. [MSB] / LBA Start cylinder No. [LSB] / LBA Start sector No.
C141-E034-02EN 5 - 27 At command completion (I/O registers contents to be read) 1F7 H (ST) Status information 1F6 H (DH) ××× DV x x 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (ER) xx xx xx x.
C141-E034-02EN 5 - 28 (11) INITIALIZE DEVICE PARAMETERS (X'91') The host system can set the n umber of sectors per track and the m axim um head num ber (max imum head n umber is "number of heads mi nus 1") per cylin der with th is comm and.
C141-E034-02EN 5 - 29 At command issuance (I/O registers setting contents) 1F7 H (CM) 11101100 1F6 H (DH) ××× DV x x 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (FR) xx xx xx xx xx At command.
C141-E034-02EN 5 - 30 Table 5.4 Information to be read by IDENTIFY DEVICE command (1 of 3) Word Value Description 0 X‘0C5A’ General Configuration *1 1 X‘0D3E’ X‘13DE’ X‘1A7C’ X‘2352.
C141-E034-02EN 5 - 31 Table 5.4 Information to be read by IDENTIFY DEVICE command (2 of 3) Word Value Description 89-127 X‘00’ Reserved 128 X‘00’ Security status not supported 129-159 X‘00.
C141-E034-02EN 5 - 32 Table 5.4 Information to be read by IDENTIFY DEVICE command (3 of 3) *8 Word 59: Transfer sector count currently set by READ/WRITE MULTIPLE command Bit 15-9: Reserved Bit 8: Mult.
C141-E034-02EN 5 - 33 (13) IDENTIFY DEVICE DMA (X'EE') When this com mand is not used to transfer data to the host in DMA mode, this co mmand functions in the same way as the Identify Device command.
C141-E034-02EN 5 - 34 Table 5.5 Features register values and settable modes Features Register Drive operation mode X‘02’ Enables the write cache function. X‘03’ Specifies the transfer mode. Supports PIO mode 4, single word DMA mode 2, and multiword DMA mode regardless of Sector Count register contents.
C141-E034-02EN 5 - 35 The host sets X' 03' to the Features register. By issuing this comm and with setting a value to the Sector Coun t register, th e transfer m ode can be selected. Upper 5 bits of the Sector C ount register defines the transfer type and lower 3 bits specifies the binary mode value.
C141-E034-02EN 5 - 36 At command issuance (I/O registers setting contents) 1F7 H (CM) 11000110 1F6 H (DH) ××× DV x x 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (FR) xx xx xx Sector count/blo.
C141-E034-02EN 5 - 37 (16) EXECUTE DEVICE DIAGNOSTIC (X'90') This comm and perf orms an intern al diagnostic test (self -diagnosis) of th e device. This comm and usually sets the DRV bit of the Drive/Head register is to 0 (however, the DV bit is not checked).
C141-E034-02EN 5 - 38 At command issuance (I/O registers setting contents) 1F7 H (CM) 10010000 1F6 H (DH) ××× DV x x 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (FR) xx xx xx xx xx At command.
C141-E034-02EN 5 - 39 At command issuance (I/O registers setting contents) 1F7 H (CM) 0010001 R 1F6 H (DH) × L × DV Head No. /LBA [MSB] 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (FR) Cylinder No. [MSB] / LBA Cylinder No. [LSB] / LBA Sector No.
C141-E034-02EN 5 - 40 At command issuance (I/O registers setting contents) 1F7 H (CM) 0011001 R 1F6 H (DH) × L × DV Head No. /LBA [MSB] 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (FR) Cylinder No. [MSB] / LBA Cylinder No. [LSB] / LBA Sector No.
C141-E034-02EN 5 - 41 At command completion (I/O registers contents to be read) 1F7 H (ST) Status information 1F6 H (DH) ××× DV x x 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (ER) xx xx xx x.
C141-E034-02EN 5 - 42 (22) IDLE (X'97' or X'E3') Upon receipt of th is comm and, the device sets th e BSY bit of the Status register, and enters the idle mode. Then, th e device clears the BSY bit, and g enerates an interrupt. The dev ice generates an interrupt even if the device has no t fully entered the idle mode.
C141-E034-02EN 5 - 43 At command completion (I/O registers contents to be read) 1F7 H (ST) Status information 1F6 H (DH) ××× DV x x 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (ER) xx xx xx x.
C141-E034-02EN 5 - 44 (24) STANDBY (X'96' or X'E2') Upon receipt of th is comm and, th e device sets th e BSY bit of the Status reg ister and enters the standby mode. The device then clears the BSY bit and gen erates an interrupt. The device generates an in terrupt even if the device has n ot fully entered the standby mode.
C141-E034-02EN 5 - 45 At command issuance (I/O registers setting contents) 1F7 H (CM) X'94' or X'E0' 1F6 H (DH) ××× DV x x 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (FR).
C141-E034-02EN 5 - 46 At command completion (I/O registers contents to be read) 1F7 H (ST) Status information 1F6 H (DH) ××× DV x x 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (ER) xx xx xx xx Error information (27) CHECK POWER MODE (X'98' or X'E5') The host checks the power mode of the device with this command.
C141-E034-02EN 5 - 47 At command issuance (I/O registers setting contents) 1F7 H (CM) X'98' or X'E5' 1F6 H (DH) ××× DV x x 1F5 H (CH) 1F4 H (CL) 1F3 H (SN) 1F2 H (SC) 1F1 H (FR).
C141-E034-02EN 5 - 48 Table 5.7 Features Register values (subcommands) and functions Features Resister Function X’D0’ SMART Read Attribute Values: A device that received this subcommand asserts the BSY bit and saves all the updated attribute values.
C141-E034-02EN 5 - 49 The host can predict failures in the device by periodically issuing the SMART Return Status subcommand (FR register = DAh) to reference the CL and CH registers. If an attribute value is below the insurance failure threshold value, the device is about to fail or the device is nearing the end of it lif e .
C141-E034-02EN 5 - 50 The attri bute va lue in form ation i s 512-by te data; th e form at of thi s data is sh own below . The host can access this data usin g the SMAR T Read Attribute Values subcom man d (FR register = D0h). The insu rance fail ure thresh old valu e data is 512-by te data; the form at of this data is show n below.
C141-E034-02EN 5 - 51 Table 5.9 Format of insurance failure threshold value data Byte Item 00 01 Data format version number 02 Attribute 1 Attribute ID 03 Insurance failure threshold 04 to 0D Threshol.
C141-E034-02EN 5 - 52 • Attribute ID The attribute ID is defined as follows: Attribute ID Attribute name 0 (Indicates unused attribute data.) 1 Reserved 2 Reserved 3 Spindle motor activation time 4 .
C141-E034-02EN 5 - 53 • Raw attribute value Raw attributes data is retained. • Failure prediction capability flag Bit 0: The attribute value d ata is saved to a medium before the device enters po wer saving mode. Bit 1: T he device automatically saves the attribute value data to a m edium after the p reviously set operation.
C141-E034-02EN 5 - 54 5.3.3 Error posting Table 5.10 lists the defined errors that are valid for each command. Table 5.10 Command code and parameters Command name Error register (X'1F1') Sta.
C141-E034-02EN 5 - 55 5.4 Command Protocol The host should confirm that the BSY bit of the Status register of the device is 0 pr ior to issue a comm and. If BSY b it is 1, the host should wait for issuing a command until BSY bit is cleared to 0. Comm ands can be executed on ly w hen th e DRDY bit of the Status register is 1.
C141-E034-02EN 5 - 56 Status read Status read *1 Wh en t h e I D D r eceives a co mmand th at h its the c ache d ata during r ead-ahe ad, and tran sf ers d ata f rom the b uff er w ithout re ading f rom the d isk me diu m. 255 2 1 0 Wor d IOCS16- IOR - Data Data R eg.
C141-E034-02EN 5 - 57 Note: For transfer of a sector of data, the host needs to read Statu s register (X'1F7' ) in order to clear INTRQ (interrupt) signal. The Status regi ster should be read w ithin a period f rom the DR Q setting by the device to 50 µ s after the com pletion of the sector data transfer.
C141-E034-02EN 5 - 58 c) When the device is ready to receive th e data of the first sector, th e device sets DRQ bit and clears BSY bit. d) The host writes one sector of data through the Data register. e) The device clears the DRQ bit and sets the BSY bit.
C141-E034-02EN 5 - 59 Note: For transfer of a sector of data, the host needs to read Statu s register (X'1F7' ) in order to clear INTRQ (interrupt) signal. The Status regi ster should be read w ithin a period f rom the DR Q setting by the device to 50 µ s after the com pletion of the sector data transfer.
C141-E034-02EN 5 - 60 5.4.4 Other commands • READ MULTIPLE • SLEEP • WRITE MULTIPLE See the description of each command. 5.4.5 DMA data transfer commands • READ DMA • WRITE DMA Starting the .
C141-E034-02EN 5 - 61 Status read 255 2 1 0 Word IOR- or IOW- DMACK- DMARQ DRQ Expanded [Single Word DMA transfer] Command BSY I NTRQ DRDY ~ Parameter write DRQ Data transfer • • • • • • .
C141-E034-02EN 5 - 62 5.5 Ultra DMA feature set 5.5.1 Overview Ultra DMA is a data tran sfer protocol used w ith the R EAD DMA an d WRITE DMA comm ands. When this protocol is enabled it shall be used instead of the Multiword DMA proto col when these comm ands are issued by the host.
C141-E034-02EN 5 - 63 5.5.2 Phases of operation An Ultra DMA data transfer is accomplished through a series of Ultra DMA data in or data out bursts. Each Ultra DMA burst has three mandatory phases of operation: the initiation phase, the data transfer phase, and the Ultra DMA burst termination phase.
C141-E034-02EN 5 - 64 11) The device shall drive the fi rst w ord of the data transfer on to DD (15:0). This step may occur when the device first drives DD (15:0) in step (10). 12) To transfer the first w ord of data the device shall negate DST ROBE within t FS after the host has negated STOP a n d a sserted HDMARD Y-.
C141-E034-02EN 5 - 65 3) T he devic e shall stop gener ating DST ROBE edges within t RFS of the host negating HDMARDY-. 4) If the host negates HDMARDY- within t SR after the dev ice has generated a DSTROBE edge, then the host shall be prepared to receive zero or one add itional data words.
C141-E034-02EN 5 - 66 10) T he device shall latch the host's CRC da ta fro m DD (15:0 ) on the ne gating edge of DMACK-. 11) The device shall compare the CRC data received from the host w ith the results of its own CRC calculation.
C141-E034-02EN 5 - 67 10) If the host has not placed the result o f its CRC calculation on DD (15 :0) since first dr iving DD (15:0) during (9), the host shall place the result of its CRC calculation on DD (15:0 ) (see 5.
C141-E034-02EN 5 - 68 9) T he device shall assert DDMARDY- w ithin t LI after the ho st has negate d ST OP. Afte r asserting DMARQ and DDMARDY- the device shall no t negate either signal until after the first negation of HSTROBE by the host. 10) T he host shall drive the first word of the data transfer onto DD (15:0).
C141-E034-02EN 5 - 69 2) The device shall pause an Ultra DMA burst by negating DDMARDY-. 3) T he host shall sto p gene rating HST ROB E ed ges within t RFS of the de vice negating DDMARDY-.
C141-E034-02EN 5 - 70 10) The device shall release DDMARDY- within t IORDYZ after the host has negated DMACK-. 11) The host shall neither negate STOP nor negate HSTROB E until at least t ACK after negating DMACK-. 12) The host shall not assert DIOW-, CS0-, CS1-, DA2, DA1, or DA0 until at least t AC K after negating DMACK.
C141-E034-02EN 5 - 71 13) The host shall neither negate ST OP no r HSTROBE until at least t ACK after negating DMACK-. 14) T he host shall not assert DIOW-, CS0-, CS1-, DA2, DA1, or DA0 until at least t ACK after negating DMACK.
C141-E034-02EN 5 - 72 5.5.6 Series termination required for Ultra DMA Series termin ation resistors are required at both the h ost and the device f or operation in any of the Ultra DMA Modes. The follow ing table describes recom mended v alues for series term ination at the host and the device.
C141-E034-02EN 5 - 73 5.6 Timing 5.6.1 PIO data transfer Figure 5.9 shows of the data transfer timing between the device and the host system..
C141-E034-02EN 5 - 74 t8 t6 t12 t11 t10 t7 t5 t4 t3 t9 t2i t2 t1 t0 Addr esses IOR DY IOCS16- R ead data DD0-DD15 Write data DD0-DD15 DIOR-/DIOW- Sy m bo l Timing parameter Min.
C141-E034-02EN 5 - 75 5.6.2 Single word DMA data transfer Figure 5.10 show the sin gle w ord DMA data transfer tim ing betw een the device and the host system. tF tE tH tG tJ tD tI tC t0 R ead data DD0-DD15 Write data DD0-DD15 DIOR-/DIOW- DMACK- DMARQ Sy m bo l Timing parameter Min.
C141-E034-02EN 5 - 76 5.6.3 Multiword data transfer Figure 5.11 sho ws the m ultiw ord DMA data transfer timing betw een the d evice and the ho st system. tF tE tH tG tJ tD tI tC t0 R ead data DD0-DD15 Write data DD0-DD15 DIOR-/DIOW- DMACK- DMARQ tK Sy m bo l Timing parameter Min.
C141-E034-02EN 5 - 77 5.6.4 Ultra DMA data transfer Figures 5.12 through 5.21 define the timings associated with all phases of Ultra DMA bursts. Table 5.12 contains the values for the timings for each of the Ultra DMA Modes. 5.6.4.1 Initiating an Ultra DMA data in burst 5.
C141-E034-02EN 5 - 78 5.6.4.2 Ultra DMA data burst timing requirements Table 5.12 Ultra DMA data burst timing requirements NA M E MODE 0 (in ns) MODE 1 (in ns) MODE 2 (in ns) COMMENT MIN MAX MIN MAX M.
C141-E034-02EN 5 - 79 NA M E MODE 0 (in ns) MODE 1 (in ns) MODE 2 (in ns) COMMENT MIN MAX MIN MAX MIN MAX t IORDYZ 20 20 20 Pull-up time before allowing IORDY to be released t ZIORDY 0 0 0 Minimum tim.
C141-E034-02EN 5 - 80 5.6.4.3 Sustained Ultra DMA data in burst 5.6.4.2 contains the values for the timings for each of the Ultra DMA Modes. Note: DD (15:0) and DSTROBE are show n at both the host and.
C141-E034-02EN 5 - 81 5.6.4.4 Host pausing an Ultra DMA data in burst 5.6.4.2 contains the values for the timings for each of the Ultra DMA Modes. Notes: 1) T he host may assert STOP to request termination of the Ultra DMA burst no sooner than t RP after HDMARDY- is negated.
C141-E034-02EN 5 - 82 5.6.4.5 Device terminating an Ultra DMA data in burst 5.6.4.2 contains the values for the timings for each of the Ultra DMA Modes. Note: The definitions for the ST OP, HDMARDY and DSTROB E signal lines are no longer in effect after DMARQ and DMACK are negated.
C141-E034-02EN 5 - 83 5.6.4.6 Host terminating an Ultra DMA data in burst 5.6.4.2 contains the values for the timings for each of the Ultra DMA Modes. Note: The definitions for the ST OP, HDMARDY and DSTROB E signal lines are no longer in effect after DMARQ and DMACK are negated.
C141-E034-02EN 5 - 84 5.6.4.7 Initiating an Ultra DMA data out burst 5.6.4.2 contains the values for the timings for each of the Ultra DMA Modes. Note: The definitions for the ST OP, DDMARDY and HSTROB E signal lines are not in effect until DMARQ and DMACK are asserted.
C141-E034-02EN 5 - 85 5.6.4.8 Sustained Ultra DMA data out burst 5.6.4.2 contains the values for the timings for each of the Ultra DMA Modes. Note: DD (15:0) and HSTROBE signals are show n at both th .
C141-E034-02EN 5 - 86 5.6.4.9 Device pausing an Ultra DMA data out burst 5.6.4.2 contains the values for the timings for each of the Ultra DMA Modes. Notes: 1) The device m ay negate DMARQ to request termination of the Ultra DMA burst no sooner than t RP after DDMARDY- is negated.
C141-E034-02EN 5 - 87 5.6.4.10 Host terminating an Ultra DMA data out burst 5.6.4.2 contains the values for the timings for each of the Ultra DMA Modes. Note: The definitions for the ST OP, DDMARDY and HSTROB E signal lines are no longer in effect after DMARQ and DMACK are negated.
C141-E034-02EN 5 - 88 5.6.4.11 Device terminating an Ultra DMA data in burst 5.6.4.2 contains the values for the timings for each of the Ultra DMA Modes. Note: The definitions for the ST OP, DDMARDY and HSTROB E signal lines are no longer in effect after DMARQ and DMACK are negated.
C141-E034-02EN 5 - 89 5.6.5 Power-on and reset Figure 5.22 shows power-on and reset (hardware and software reset) timing. (1) Only master device is present *1: R ese t me ans includ ing Po w e r-on-R ese t, H ardw are R ese t (R ESET-), and So ftw ar e R e se t.
C141-E034-02EN 6 - 1 CHAPTER 6 OPERA TIO NS 6.1 Device Response to the Reset 6.2 Address Translation 6.3 Power Save 6.4 Defect Management 6.5 Read-Ahead Cache 6.
C141-E034-02EN 6 - 2 6.1.1 Response to power-on After th e master device (dev ice 0) releases its own pow er-on reset state, th e master device sh all check a DA SP- sign al for up to 450 m s to conf irm presen ce of a slav e device (device 1).
C141-E034-02EN 6 - 3 6.1.2 Response to hardware reset Response to RESET- (hardware reset through the interface) is similar to the power-on reset. Upon receipt of h ardware res et, the mas ter device check s a DASP- s ignal for up to 450 ms to confirm presence of a slav e device.
C141-E034-02EN 6 - 4 6.1.3 Response to software reset The master device does n ot check the DASP- sig nal for a softw are reset. If a slave device is present, the m aster device checks th e PDIAG- signal for u p to 31 seconds to see if the slave device has completed the self-diagnosis successfully.
C141-E034-02EN 6 - 5 6.1.4 Response to diagnostic command When the m aster device receives an EXECUTE DEVICE DIAGNOSTIC com m and and the slave device is present, the master device checks the PDIA G- signal for up to 6 seconds to see if the slave device has completed the self-diagnosis successfully.
C141-E034-02EN 6 - 6 6.2 Address Translation When the IDD receives an y com mand w hich inv olves access to the disk m edium, th e IDD always implem ents the address translation from th e logical address (a host-specifi ed address) to the physical address (logical to physical address translation).
C141-E034-02EN 6 - 7 6.2.2 Logical address (1) CHS mode Logical address assig nmen t starts from ph ysical cy linder (PC) 0, phy sical head (PH) 0, and phy sical sector (PS) 1 and is assigned by calculating th e num ber of sectors per track which is specified by the INITIALIZE DEVIC E PARAMETERS com man d.
C141-E034-02EN 6 - 8 (2) LBA mode Logical address assignm ent in the LBA m ode starts from phy sical cylin der 0, physical h ead 0, and phy sical sector 1. The logical address is advanced at the subsequen t sector from the last sector of the current track.
C141-E034-02EN 6 - 9 Regardless of w hether the power dow n is enabled, the device enters th e idle mode. The device also enters the idle mode in the same way after power-on sequence is completed. (1) Active mode In this m ode, all the electric circuit in th e device are active or the dev ice is under seek, read or write operation.
C141-E034-02EN 6 - 10 • STANDBY IMMEDIATE command • INITIALIZE DEVICE PARAMETERS command • CHECK POWER MODE command (4) Sleep mode The power consumption of the drive is minimal in this m ode. T he drive enters only the standby mode f rom t he sleep m ode.
C141-E034-02EN 6 - 11 6.4.1 Spare area Following two types of spare area are provided for every physical head. 1) Spare cylinder for sector slip: used for alternating defective sectors at formatting in shipment (11 cylinders/head) 2) Spare cylinder for alternative assignment: used for alternative assignment by automatic alternative assignment.
C141-E034-02EN 6 - 12 (2) Alternate cylinder assignment A defective sector is assigned to the spare sector in the alternate cylinder. This processing is performed when the automatic alternate processing is performed. Figure 6.8 shows an example where (physical) sector 5 is detective on head 0 in cylinder 0.
C141-E034-02EN 6 - 13 (3) Automatic alternate assignment The device performs the automatic assignment at following case. 1) When ECC correction perform ance is increased du ring read error retry , a read error is recovered. Before autom atic alternate assignm ent, the dev ice performs rewriting the corrected data to the erred sector an d rereading.
C141-E034-02EN 6 - 14 6.5.2 Caching operation Caching operation is perform ed only at issu ance of the f ollowin g comm ands. The device transfers data from the data buffer to the host system at issuance of f ollowing comm and if following data exist in the data buffer.
C141-E034-02EN 6 - 15 (3) Invalidating caching data Caching data in the data buffer is invalidated in the following case. 1) Following command is issued to the same data block as caching data.
C141-E034-02EN 6 - 16 1) Sets the host address pointer (HAP) and the disk address pointer (DAP) to the lead of segment. Se gme nt only fo r r ead DAP HAP 2) T ransfers the requested data th at already read to the h ost system w ith reading the requested data from the disk media.
C141-E034-02EN 6 - 17 (3) Sequential read When the disk driv e receives the read comm and that targets the sequential address to the previous read command, the disk drive starts the read-ahead operation.
C141-E034-02EN 6 - 18 4) The disk dr ive performs the read-ahead operatio n for all area of segment with overwriting the requested data. Finally, the cache data in the buffer is as follows.
C141-E034-02EN 6 - 19 3) After com pletion o f data transfer of hit data, the disk d rive pe rforms the read-ahead operation for the data area of which the disk drive transferred hit data. R ead -ahead d ata 4) Finally, the cache data in the buffer is as follows.
C141-E034-02EN 6 - 20 1) In the case that th e contents of th e data buff er is as follow s for exam ple and the previous comm and is a sequential read com man d, the disk drive sets the HAP to the address of which the hit data is stored.
C141-E034-02EN 6 - 21 1) The disk dr ive sets the HAP to the addr ess wh ere the partially hit data is sto red, and sets the DAP to the address just after the partially hit data. HAP DAP Partially h it data Lac k d ata 2) T he disk driv e starts transferring partially hit data and reads lack data from the disk media at the same time.
C141-E034-02EN 6 - 22 6.6 Write Cache The write cach e function of the drive m akes a high speed processing in th e case that data to be written by a write comm and is logically sequent the data of p revious comm and and rand om write operation is performed.
C141-E034-02EN 6 - 23 At the tim e that th e drive has s topped the com man d execution af ter the error recovery has f ailed, the w rite cache fun ction is disabled autom atically. The releasing the disable state can be don e by the SET FEA TURES comm and.
FUJITSU LIMITED OEM Marketing 4-1-1, Kamikodanaka, Nakahara-Ku, Kawasaki, 211-88, Japan TEL: 044-754-8632 FAX: 044-754-8634 FUJITSU COMPUTER PRODUCTS OF AMERICA, INC. 2904 Orchard Parkway, San Jose, California 95134-2009, U.S.A. TEL: 1-408-432-6333 FAX: 1-408-432-3908 FUJITSU CANADA INC.
FUJITSU ESPAÑA S.A. C/ Almagro 40, 28010 Madrid, SPAIN TEL: 34-1-581-8100 FAX: 34-1-581-8125 FUJITSU AUSTRALIA LIMITED 475 Victoria Avenue, Chatswood, 2067 N.
Reader Comment Form We would appreciate your comments and suggestions for improving this publication. Publication No. Rev. Letter Title Current Date How did you use this publication? Is the material presented effectively? What is your overall rating of this publication? What is your occupation? Your other comments may be entered here.
デバイスFujitsu MPA3035ATの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Fujitsu MPA3035ATをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFujitsu MPA3035ATの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fujitsu MPA3035ATの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fujitsu MPA3035ATで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fujitsu MPA3035ATを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFujitsu MPA3035ATの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fujitsu MPA3035ATに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFujitsu MPA3035ATデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。