Gracoメーカー215-433 Series Gの使用説明書/サービス説明書
ページ先へ移動 of 22
INSTRUCTIONS-PARTS LIST 307-293 This manual contains IMPORTANT WARNINGS and INSTRUCTIONS READ AND RETAIN FOR REFERENCE PORTABLE, AIRLESS GH 433 PAINT SPRAYER 3000 psi (210 bar) MAXIMUM WORKING PRESSURE Model 215-433, Series G Includes Sprayer 231-005, Hose, Gun, Tip Guard and Spray Tip of Choice.
WARNING HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY. For professional use only. Observe all warnings. Read and understand all instruction manuals before operating equipment. FLUID INJECTION HAZARD General Safety This equipment generates very high fluid pressure.
EQUIPMENT MISUSE HAZARD General Safety Any misuse of the spray equipment or accessories, such as overpressurizing, modifying parts, using incompatible chemicals and fluids, or using worn or damaged parts, can cause them to rupture and result in fluid injection or other serious bodily injury, fire, explosion or property damage.
TERMS WARNING: Alerts user to avoid or correct conditions that could cause bodily injury. CAUTION: Alerts user to avoid or correct conditions that could cause damage to or destruction of equipment. TYPICAL INSTALLATION FLUID HOSE Fig 2 SETU P U;;ti/'WH:nA NOTE: Numbers in parentheses refer to the parts list on page 19.
4. Fill the Packing Nut/Wet Cup (141) 1/4 full with Graco Throat Seal Liquid nsu, supplied. 5. Check the Hydraulic Oil Level a. Unscrew the oil fill cap. See Fig 3. The dipstick is attached to the cap. Wipe off the dipstick and set it in the hole, but do not thread it in place.
FLUSHING GUIDELINES When to Flush 1. New Sprayer. Your new GH 433 Sprayer was fac- tory tested in lightweight oil which was left in to protect pump parts from corrosion. Before using oil-base paint, flush with mineral spirits only. Before using water-base paint, flush with mineral spirits, followed by soapy water, then a clean water rinse.
10. Point the gun into the metal pail and hold a metal part of the gun firmly against the pail. See Fig 7. ..-----~WARNING-----.., To reduce the risk of static sparking, which can cause fire or explosion, always hold a metal part of the gun firmly against a grounded metal pail when flushing.
WARNING --------------~ Pressure Relief Procedure To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, always foll.
f. After the engine is warm, gradually open the choke lever and close the bypase valve. See Fig 8 and 9. NOTE: In cold weather, run the engine for about 15 minutes with the bypass valve open before starting the displacement pump to help avoid hydraulic motor stalling.
1. Always stop the pump a the bottom of Its stroke when you take a break and at the end of the day. This helps keep fluid from drying on the rod and damaging the packings. 2. Keep the displacement pump packing nut/wet-cup 1/4 full of TSL at all times.
~-----------------------------WARNING------------------------------~ To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, always follow the Pressure Relief Procedure Warning as given on page 2 or 8 before troubleshooting or repairing your sprayer.
Disconnect the Displacement Pump 1. Solvent flush the displacement pump if possible. Stop the pump on the down stroke. 2. Follow the Pressure Relief Procedure Warning on page 8. 3. Remove the accessory suction tube, if used, and remove the fluid hose from the displacement pump.
Intake Valve (See Fig 13) 1. Unscrew the extension (62), if used, and remove the retaining ring (52) and strainer (51) from the ex- tension. Clean the parts in solvent. 2. Screw the intake valve housing (138) out of the pump housing (140). 3. Remove the ball stop pin (132), ball guide (136), ball (125) and o-ring (133)from the intake valve housing.
Replacing the Hydraulic Pump 1. Follow the Pressure Relief Procedure Warning on page 8. Let the hydraulic system cool before beginning the service procedure. 2. Unscrew the reservoir drain plug (7), having a con- tainer ready to catch the draining fluid.
Drive Unit (See Figs 14 and 15) 1. Disconnect the hydraulic inlet hose (92) from the paint pump's 90° swivel union (45), 2. Loosen the coupling nut of the elbow (41) and disconnect the hydraulic oil drain hose (2) from the oil cooler inlet elbow (41).
" bold letters (A) re NO TE: Corresp~md~nJ1nnections" - --------;;--;-;::;----- and tubing 110 6 307-293 el 215-433, Series G Mod "tems2-171 17-" .
64 27 160 -- ____ .... 433 Series G Model 2~5- 2-171 Includes Items 006 Series A Model ~1- 2-169, 171 Includes Items 102 58 307-293 11.
Ref No 110 Includes items 111-142, 171 Ref No. 123 Includes items 124-142 118 140 128~~. ~ 129 ~ ~ I 122 (see 306-980 for parts) 142 ~ U~130 ~.-=~ 137 ®' 114 .. 127 ~ 117 ./'"115 . ,.?--111 135~. ~::~ 208-919 Pump Repair P (Ord~r separately).
PARTS LIST Model 215-433, Series G Model 231-005, Series A Includes items 2-171 Includes items 2-169, 171 REF PART DESCRIPTION OTV REF PART DESCRIPTION OTV NO.
ACCESSORIES (Must be purchased separately) FLUID GAUGE 102-814 , 5000 psi (350 bar) MAXIMUM WORKING PRESSURE Install to read pressure in hydraulic fluid system. .if.· . KEEP DIRT OUT OF SYSTEM SELECT-A-FAN (with tips) 206-310 3000 psi (210 bar) MAXIMUM WORKING PRESSURE Fits the fan pattern to both wide and narrow surfaces and clears tip stoppages.
SERVICE INFORMATION Listed below by the assembly changed are OLD, NEW, ADDED and DELETED parts. ASSEMBLY PART REF PART NAME CHANGED STATUS NO. NO. 215-433 and OLD 100-063 Cotter Pin 231-005** NEW 19 1.
TECHNICAL DATA Engine Gasoline Tank Hydraulic Pump Hydraulic Fluid Sump Hydraulic Pump Suction Filter Hydraulic Oil Return Filter Fluid Filter Displacement Pump Wetted Parts Weight Noise Level Overall Dimensions Wisconsin Robin, Model EY laW, 4 cycle, single cylinder, air cooled, 4.
デバイスGraco 215-433 Series Gの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Graco 215-433 Series Gをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco 215-433 Series Gの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco 215-433 Series Gの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco 215-433 Series Gで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco 215-433 Series Gを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco 215-433 Series Gの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco 215-433 Series Gに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco 215-433 Series Gデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。