Gracoメーカー233940の使用説明書/サービス説明書
ページ先へ移動 of 20
Operation GRACO INC.ąP .O. BOX 1441ąMINNEAPOLIS, MNą55440-1441 Copyright 2002, Graco Inc. is registered to I.S. EN ISO 9001 GH 200 Sprayer 309548 Rev . C Read warnings and instructions. 233940 Contents: Controls 3 . . . . . . . . . . . . . . . .
2 309548 Danger d’incendie et d’explosion : les gaz de solv ant et de peinture peuvent s’enf lamm er ou exploser . Pour évi ter les risques d’ incend ie et d’expl osio n : N’ut iliser l’app areil qu e dan s une zone extrêmem ent bien aérée.
3 309548 CONTROLS On/Off Switch Drain V alve Pump valve Pressure Control T rigger Lock on off On/Off Switch Engine Controls ti2267a Contractor Contractor II Contractor Contractor II.
4 309548 Setup Unplug motor power cord or turn engine switch OFF . Change Engine or Motor 1. Loosen motor clamp and swivel bracket. Lift strap. 2. Lift belt guard. T ilt engine/motor . Remove engine/motor . WARNING MISE EN GARDE ADVERTENCIA ADVERTÊNCIA 3.
5 309548 Complete Setup 1. Connect appropriate Graco high-pressure hose to sprayer . T ighten securely . Note: Remove second gun port cap for multiple guns and repeat steps 1 – 4. 2. Connect other end of hose to gun. 3. T ighten securely . 4. Remove tip guard.
6 309548 5. Install clean inlet strainer . 6. Fill throat packing nut with TSL to prevent premature packing wear . Do this each time you spray and store. Approximate Fill Level 7. Check engine oil level. Add SAE 10W–30 (summer) or 5W–20 (winter), if necessary .
7 309548 8. Fill fuel tank. WARNING MISE EN GARDE ADVERTENCIA ADVERTÊNCIA 9. Check hydraulic oil level. Add only Graco Hydraulic Oil, Grade 6, 169236 (5 gallon/18.9 liter) or 207428 (1 gallon/3.8 liter). Hydraulic tank capacity is 1 gallon (3.8 liter).
8 309548 Startup 1. Place suction tube and drain tube in grounded metal pail partial- ly filled with flushing fluid. Attach ground wire to pail and to earth ground. P AINT FLUSH 2. T urn prime valve down. T urn pressure control counterclockwise to lowest pressure.
9 309548 4. Start engine a. Move fuel valve to open b. Move choke to closed c. Set throttle to fast d. Set engine switch ON e. Pull starter cord f. After engine starts, move choke to open g.
10 309548 5. Set pump valve ON . – Hydraulic motor is now active – ON 6. I ncrease pressure enough to start hydraulic motor stroking and allow fluid to circulate for 15 seconds; turn pressure down, turn prime valve horizontal. 15 SEC 7. T ake spray gun trigger safety OFF .
11 309548 8. Hold gun against grounded metal flushing pail. T rigger gun and increase fluid pressure slowly until pump runs smoothly . FLUSH Inspect fittings for leaks. Do not stop leaks with your hand or a rag! If leaks occur , turn sp r ayer OFF immediately .
12 309548 9. Place siphon tube in paint pail. P AINT 10. T rigger gun again into flushing fluid pail until paint appears. Assemble tip and guard, page 13.
13 309548 SwitchTip and Guard Assembly 1. Insert SwitchT ip. Insert seat and OneSeal. SwitchT ip OneSeal seat 2. Screw assembly onto gun. Hand tighten. Clearing Tip Clogs WARNING MISE EN GARDE ADVERTENCIA ADVERTÊNCIA 1. Release trigger , put trigger safety ON.
14 309548 Cleanup Pressure Relief WARNING MISE EN GARDE ADVERTENCIA ADVERTÊNCIA 1. Set pump valve OFF . T urn engine OFF . OFF Pressure Relief WARNING MISE EN GARDE ADVERTENCIA ADVERTÊNCIA 2. T urn pressure to lowest setting. T rigger gun to relieve pressure.
15 309548 5. Unscrew bowl, remove filter . Assemble without filter . Clean filter . 6. Clean filter , guard and SwitchT ip in flushing fluid. FLUSH 7. Remove siphon tube set from paint and place in flushing fluid. Use water for water base paint and mineral spirits for oil base paint.
16 309548 8. T urn engine ON and start engine. Set pump valve ON. ON 9. T urn prime valve horizontal. 10. Hold gun against paint pail. T ake trigger safety OFF . T urn pressure control up until motor begins to drive pump . T rigger gun until flushing fluid appears.
17 309548 11 . Move gun to flushing pail, hold gun against pail, trigger gun to thoroughly flush system. Release trigger and put trigger safety ON . FLUSH 12. T urn prime valve down and allow flushing fluid to circulate for approximately 20 seconds to clean drain tube.
18 309548 14. Make sure plastic center tube is tightened securely . Install filter bowl and filter . Hand tighten filter bowl. Hand tighten gun handle. 15. Wipe sprayer , hose and gun with a rag soaked in water or mineral spirits. 16. Clean tip, guard and gasket with a soft bristle brush to prevent part failure due to dried materials.
19 309548 T roubleshooting T o reduce risk of serious injury , when instructed to relieve pressure, do steps 1. – 3.; page 14. PROBLEM CAUSE SOLUTION Gas engine pulls hard (won’t start) Hydraulic .
20 309548 Graco W arranty Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use.
デバイスGraco 233940の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Graco 233940をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco 233940の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco 233940の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco 233940で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco 233940を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco 233940の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco 233940に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco 233940デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。