Gracoメーカー258859の使用説明書/サービス説明書
ページ先へ移動 of 24
3A0153E Operation Pr oShot ™ Cor dless P aint Spra y er U .S. Patent No. D625,775 S; U .S. P atent No. 6,619,569; U.S. P atent No. D630,708 S; Community Registration #0012282 55; India Patent No. 230058; T aiwan P atent No. D142952 China P atent No.
Table of Contents 2 3A0153E T able of Contents W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Component Ident ification . . . . . . . . . . . . . . . . . . . . . . . . . 5 Common Pr ocedures . . . . . . . . . .
Warnings 3A0153E 3 Wa r n i n g s The follo wing war nings are for the setup , u se, maintenance, and repair of this equipment. The exclamation point symbol aler ts y ou to a general warning and the ha zard symbols refer to procedure-sp ecific risks. When these symbols appear in the body of this manual, ref er back to these W ar nings.
Warnings 4 3A0153E B A TTERY HAZARD The batter y may leak, e xplode, cause b ur ns, or cause an e xplosion if mishandled. Contents of an open battery can cause se vere irritation and/or chemical burns. If on skin, wash with soap and w ater . If in ey es, flush with water f or at least 15 minutes and seek immediate medical attention.
Component Identification 3A0153E 5 Component Identification *NO TE: Filter asse mbly is re verse-threaded. T ur n left (or count er-clockwise) to tighten, tur n right (or clockwise) to loosen.
Common Procedures 6 3A0153E Common Pr ocedures Pressure Relief Pr ocedure 1. Engage tr igger lock. 2. Put prime/relief v alve UP to re lease pressure. Tr i g g e r L o c k Spra y Tip P osition Prime/Relief V a lve P osition Do not opera te or spra y near children.
Charging the Battery 3A0153E 7 Char ging the Batter y Batteries are initially 50% charge s to provide optimum battery life and requir e charging before first use. It takes approximatel y 45 minutes to charge a dead battery to 80%, at which point it can be used.
Setup 8 3A0153E Setup Suction T ube Selection This spra yer comes with two different suction tubes . Standar d Suction T ube (sprays ceilings and walls): When spra ying walls, the inlet of the suction tube should be aimed at the fr ont of the material cup .
Setup 3A0153E 9 Spra ying Stains or Clear Coats (Fine-Finish Optimizer) The Fine-Finish Optimizer should be installed and us ed when spraying thin materi al such as stain or cle ar coats. The Fine-Finish Op timizer restricts the mat er ial flo w resulting in a finer quality finish.
Setup 10 3A0153E Materials • When spr aying water -based materials, flush the spra yer thoroughly with water . • When spr aying non-wate r-based material s, flush the spra yer thoroughly with mineral spirits or com- patib le, oil-based flushing fluid.
Install Tip/ Guard Assembly (if not installed) 3A0153E 11 Install Tip/Guar d Assembl y (if not installed) Rever sible Tip Selection Chart 1. Engage trigger lock and put prime/relief valv e UP to release pressure . Then remove Tip/Guard Assemb ly . 2. Install filter to Spra y Tip/Guard Assembly (make sure filter is fully installed into spra yer).
Unclogging Spray Tip/Guard Asse mbly 12 3A0153E Unc logging Spra y Tip/Guar d Assembl y 1. T o unclog tip obstr uction, en gage trig ger lock and pull relief valv e UP to release pressure. 2. Re verse spra y tip to UNCLOG position. 3. Aim spra yer at waste area, disengag e trigger lock, and put prime/relief v alve DO WN to spra y positio n.
Shutdown and Cleaning 3A0153E 13 Shutdo wn and Cleaning Flushing Spra yer 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remo ve material cup and pr oper ly dispose cup liner or e xcess material.
Shutdown and Cleaning 14 3A0153E 6. Disconnect trigger loc k and trigger spra yer f or appro ximately 15 se conds. Engage trigger loc k. 7. Discard contaminated fluid and refill with appropr i- ate flushing fluid. 8. Disengage trigger loc k, re verse tip to UNCLOG position, and pull trigger f or 5 seconds to prime spra yer .
Storage 3A0153E 15 Cleaning Spra yer Exterior • Wipe paint off out side of spra yer using a soft cloth moistened with w ater or flushing fluid. Do NO T submerge the spra yer . Tips • Tips will require replac ement depending on abrasiveness of paint.
Replacement Parts and Kits 16 3A0153E Replacement P ar ts and Kits 1 8 11 6 5 4 3 7 12 16 ti15497a 2 15 14 17 9 10 18 20 19 21 22 23 24 ti16473c 13a 13 13a 13 Ref.
ProShot Repair Kit 3A0153E 17 Pr oShot Repair Kit Outlet V alve Fitting NO TE: Before doing any repair to pump, perf or m Flushing Spra yer procedure, pa ge 13. Re m ova l 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remove battery .
Alternate Priming Method 18 3A0153E Alternate Priming Method 1. Engage tr igger lock and put pr ime/re lief valv e UP to release pressure . 2. Remov e material cup and f ill with flushing mater ial. 3. With spray er in pr ime mode, tur n spray er upside-down, remov e strainer and slowly pour flush- ing mater ial into the in take tube until full.
Alternate Priming Method 3A0153E 19 Inlet V alve Cleaning Re m ova l 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remov e material cup and suction tube. 3. Hold spr ay er upside-down and use wrench or sock et to loosen and re move inlet fitti ng, inlet valv e, and spring.
Troubleshooti ng 20 3A0153E T roub leshooting Chec k ev er ything in this T roub leshooting T ab le before you br ing the spra y er to an authorized service center . Prob lem Cause Solution ProShot makes no sound when trigger is pulled T rigger is locked.
Troubleshooting 3A0153E 21 Spra y Pattern Dia gnostics ProShot spra ys with poor results Tip is par tially clogged See Unclog ging Tip/Guard Assembly , page 12. Tip is not in correct position Rotate tip to SPRA Y position. Incorrect tip f or application of material.
Troubleshooti ng 22 3A0153E Spra y patter n is too narrow: Spray er is too close to target surface . Incorrect tip for appli cation of material . Tip is worn or damaged . Mov e spray er awa y from surface (10 in). See Reversible Tip Selection Chart, page 11.
Technical Data 3A0153E 23 Te c h n i c a l D a t a Sprayer: 258865 258859 Maximum working pressure 2000 psi (137.8 bar , 13.7 MP a) W eight 6.32 lb (2.
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions. T his manual contains English.
デバイスGraco 258859の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Graco 258859をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco 258859の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco 258859の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco 258859で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco 258859を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco 258859の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco 258859に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco 258859デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。