Gracoメーカー3A0156Bの使用説明書/サービス説明書
ページ先へ移動 of 20
3A0156B EN Operation Electric Airless Spra yer s For P ort able Airless Spra ying of Architectu ral Coatings and P aints. For pr ofessional use only . Not appro ved for use in Eur opean explosive atmo sphere locations.
Models: 2 3A0156B Models: 695 UL TRA MAX lIl Model QuikReel Hi-Bo y Lo-Bo y 258719 ✓✓ 258720 ✓ 258722 ✓ 258872 ✓ 258873 ✓ 258874 ✓ 258876 ✓ 258877 ✓✓ 826124 ✓✓ 826125 ✓ 82612.
Warnings 3A0156B 3 W arnings The f ollowing warnings are for the setup, use , grounding, maintenance and repair of t his equipment. The exclamation point symbol aler ts you to a general w ar ning and the hazard symbol ref ers to procedure-specific risks.
Warnings 4 3A0156B FIRE AND EXPLOSION HAZARD Flammable fumes , such as solvent and paint fumes , in work area can ignite or explode . T o help prev ent fire and e xplosion: • Do not spra y flammable or comb ustible materials near an open flame or sources of ignition such as cig- arettes, motors , and electrical equipment.
Warnings 3A0156B 5 W ARNING EQUIPMENT MISU SE HAZARD Misuse can cause death or serious injur y . • Alwa ys wear appropriate glov es, ey e protection, and a respirator or mask when painting. • Do not operate or spra y near children. K eep children awa y from equipment at all times.
Component Identification 6 3A0156B Component Identification ti14839b 11. 12. 10. 13. 1. 2. 4. 5. 6. 7. 8. 9. 3. 1 Premium Digital Display 2 ON/OFF Switch 3 W atchDog ™ Switch (not a vailab le on Mar.
Grounding 3A0156B 7 Gr ounding The spra yer must be gr ounded. Grounding reduces the risk of static and electric shoc k by pro viding an escape wire f or the electrical current due to static build up or in the e vent of a shor t circuit. The spra yer cord includes a ground ing wire with an appropriate gro unding contact.
Pressure Relief Procedure 8 3A0156B 15/20 Amp Switch (Not A vailab le on All Units) Select 15A or 20A setting based on y our circuit rating. Pressure Relief Pr ocedure 1. T ur n power OFF . Wait 7 seconds for power to dissipate. 2. Lock gun trigger sa f ety .
Setup 3A0156B 9 Setup 1. Standard Units Only : Connect Graco airless hose to spra yer . Tighten securely . 2. Standard Units Only : Connect other end of ho se to gun and tighten securely . 3. Engage gun t rigge r safety . 4. Remo ve tip guard. 5. Check inlet strainer f or clogs an d debr is.
Startup 10 3A0156B Star tup 1. T ur n pressu re control t o lowest pressure. 2. T ur n power ON . 3. Increase pressur e 1/2 tur n to star t motor and allow fluid to circulat e through drain tube f or 15 seconds; turn pressure do wn. 4. T ur n prime valv e forw ard to SPRA Y position.
Switch Tip Installation 3A0156B 11 Switch Tip Installation 1. Use spray tip (A) to inser t O neSeal ™ ( B) into guard (C). 2. Inser t Switch Tip. 3. Scre w assembly on to gun. Tighten. Spra y 1. Spra y test patte r n. Increa se pressure to eliminate heavy ed ges.
WatchDog ™ Protection System (Not Available on All Uni ts) 12 3A0156B W atc hDog ™ Pr otection System (Not A vailable on All Units) Pump stops automatically wh en mater ial pail is empty . To A c t i v a t e : 1. P erform Star tup . 2. Premium units with digi tal display: T ur n Wat chDog switch ON and WD ON displays .
Hose Reel (Not Available on All Units) 3A0156B 13 Hose Reel (Not A vailable on All Units) 1. Mak e sure hose is routed through hose guide. 2. Lift and turn pivot loc k 90° to unloc k hose reel. Pull on hose to remo ve it from ho se reel. 3. Pull reel hand le up and tur n clockwise to reel in hose .
Digital Tracking System (Not Available on All Uni ts) 14 3A0156B Digital T rac king System (Not Av ailable on A ll Units) Operation Main Menu Shor t press to mo ve to ne xt displa y . Press and ho ld (5 seconds) to chang e units or reset data. 1. T ur n pressu re to lowest setting.
Digital Tracking System (Not Available on All Units) 3A0156B 15 Secondary Menu - Stored Data and W a tchDog Pump Pr otection Modes 1. P erform Pressure Relief, st eps 1 - 4 if they hav e not already been do ne. 2. T ur n power s witch on while holding DTS button down.
Cleanup 16 3A0156B Cleanup 1. P erform Pressure Relief Pr ocedure (page 8), steps 1 - 4. Remo ve siphon tube set fro m paint and place in flushing flui d. Remove tip guard from gun. NO TE : U se wat er for wa te r- ba se paint, mineral spirits f or oil-base paint, or other solv ents recommended b y manuf acturer .
Cleanup 3A0156B 17 9. Remov e filters from g un an d spra yer , if installed. Clean and inspect. Install filters. 10. If flushing with water , flush ag ain with mineral spir its, or Pump Ar mor , to leave a protectiv e coating to pre- vent freezing or corrosion.
Technica l Data 18 3A0156B Te c h n i c a l D a t a Basic Sprayer Wetted Parts......... ..................... zinc- and nick el-plate d carbon steel, nylon, stainless steel, PTFE, Acetel, leather , UHMWPE, aluminum tungsten carbide, PEEK, brass Noise Level Sound powe r .
Notes 3A0156B 19 Notes.
All written and visual data contained in this document reflects the latest product info rmation available at th e time of publica tion. Graco reserves the right to make changes at any time without notice. Original instructions. This manual contains English.
デバイスGraco 3A0156Bの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Graco 3A0156Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco 3A0156Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco 3A0156Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco 3A0156Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco 3A0156Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco 3A0156Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco 3A0156Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco 3A0156Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。