Graco Inc.メーカー237-410の使用説明書/サービス説明書
ページ先へ移動 of 17
.
3X8–448 Rev . F Supersedes Rev . C Includes Rev . D and E changes Parts Change Notice Some parts in Rev . C of manual 308–448 have changed but have not yet been changed in the instruction manual. Please note the changes below and mark them in your manual or keep this sheet with your manual.
Table of Contents Symbols Warnings ...................................... 2 Setup.. ....................................... 4 System Component Information .................. 6 Operation ..................................... 8 Flushing ................
EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result in serious injury. 0 0 l 0 0 0 0 0 0 0 This equipment is for professional use only. Read all instruction manuals, tags, and labels before operating the equipment.
A CAUTION This equipment is compatible with most water based materials. See the wetted parts in the Tech- nical Data section and your fluid and solvent manufacturer’s compatibility information. Do not use catalyzed materials in heated applica- tions.
III. Unpacking the System In addition to the assembled unit, these components are packed loosely or separately: suction assembly, hose set, gun, instruction manuals. These are the manuals you should receive: 308-I 94 Husky 307 pump 307-452 Air spray gun 308-325 Fluid regulator 307-805 Fluid heater 307-273 Fluid filter IV.
System Component Information VI. Using the G700N Air Spray Gun 1. 2. 3. 4. 5. 6. 7. Refer to Fig. 3. Make initial fluid and air adjustments at the pump for maximum efficiency. If you make adjustments at the gun, take noted of what you do. Then, if the results are not satisfac- tory, you can easily return the gun to its previous adjustment.
System Component Information VIII. Using the Air Regulators and Needle 1. 2. 3. 4. 5. valve See Fig. 5. Always open air and fluid regulators slowly to pre- vent surging during startup. The air regulator (6a) on the right side of the pump controls air to the pump, and the regulator (6b) on the left side controls air to the gun.
Operation I. Pressure Relief Procedure The system remains pressurized until pressure is manually relieved. To reduce the risk of serious injury from pressurized fluid, accidental spray from the gun, o.
Operation 12. Adjust the needle valve to set the pump cycle rate at 1 stroke every 15 seconds. 13. Turn the heater dial to 3. Whenever the heater set- ting is changed, allow the fluid to circulate and sta- bilize before checking the temperature (about IO minutes) .
Operation v. Production Spraying You are now ready for production spraying. If you stop spraying for more than 30 minutes, turn off the heater to prevent overheating the fluid. VI. Shutting Down the System Shut down the system at the end of the work shift and before checking, adjusting, cleaning, or repairing the system.
Flushina +a 14. 15. KEY A Bleed-type master air valve C Air line 3 Fluid heater 6a Pump air regulator 6b Gun air regulator 9 3-way valve 13 Drain hose 44 Fluid regulator 45 Fluid filter 48 Filter drain valve For a first-time flush, trigger the gun, and circulate the solvent for 20 seconds.
Parts Model 237410, Series A Ref Part No. No. 1 235-230 2 217-752 3 220-522 4 110-160 5 108-233 6 111-804 7 11 O-209 8 108-l 90 9 214-711 10 214-699 11 205-l 69 12 206-966 13 206-965 14 188-l 73 15 16.
Parts 16’ Model 237410, Series A 25 60 / 23 308-448 13.
Notes . 14 308-448.
Notes c 308-448 15.
Technical Data Manual Change Summary The current revision of this manual includes the following changes: Page 12, Parts List: l The quantity of item 25 (elbow) is changed to 3. l The quantity of item 47 (elbow) is changed to 1. Page 13, Parts Drawing: l Item 60 is changed to 62, and item 62 is changed to 60.
デバイスGraco Inc. 237-410の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Graco Inc. 237-410をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco Inc. 237-410の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco Inc. 237-410の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco Inc. 237-410で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco Inc. 237-410を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco Inc. 237-410の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco Inc. 237-410に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco Inc. 237-410デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
