Graco Inc.メーカー248083の使用説明書/サービス説明書
ページ先へ移動 of 22
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2003, Graco Inc. is r egistered to I. S. EN ISO 9001 309915D Operation T e xSpra y GTX™ 2000 US P atents D502,532; 7,114 ,664 - For W ater -Based Materials Only - Model: 248082 Spray er with Graco T rigger Gun 120 psi (8.
Warnings 2 309915D The f ollowing W arnings are for the safe se tup, use, grounding, maint enance and repair of this equipment. The exc lamatio n point symbol alerts you to a general warning an d the hazard symbo ls refer to procedure-specific risks. Refer back to these W arnings.
Warnings 309915D 3 W ARNINGS Burn Hazard Equipment surf aces and fluid that is heated can becom e very hot during operation. T o av oid sev ere burns, do no t touch hot fluid or equi pment. W ait until equipment /fluid has cooled complete ly . Pressurized Equipment Hazard Compressed a ir can inje ct in skin.
Component I dentification 4 309915D Component Identification WLE < ' & % . / * ) + - 8 7 1 0 3 5 : $ 6 ( = 4 9.
Component I dentification 309915D 5 Component Identification * Ref erence numbers used in gun illustration s coincide with reference numbers shown in gun manual 3 08878 A Gas T ank B Fuel V alve C Cho.
Pressure Relief Procedure 6 309915D Pressure Relief Pr ocedure IMPORT ANT T o reduce the risk of in jur y , f ollow this Pressur e Relief Pr ocedure whene ver you: • Are instructed to relieve pressure • Stop spra ying • Ser vice equipment • Install or clean spra y nozzle • Disconnect or connect hose.
Setup 309915D 7 Setup Preparation 4 Connect air and material hoses to gun. Tighten securely). 5 Connect one end of mater ial hose (cc) to material outlet (K or L) and the other end to gun material inlet (bb). NO TE: Materi al plug must be installed in material outlet (K or L) you are not using.
Setup 8 309915D Compressor P o wer Pa ck Removing Compressor P ower P ack (Z) For outdoor us e , the co mpressor power pack (Z) can be lef t on the cart.
Setup 309915D 9 Reinstalli ng Compressor P o wer Pa ck (Z) Note: For maxim um performance use a 3/8 in. or 1/2 in. inside diameter hose. Hose must be rated f or : • 200°F (93°C) maximum temperatur.
Setup 10 309915D W etting Hose Wet inside of hose before each use to flush out sed iment and pr ev ent te xture material from p acking out hose. 1 P our one (1) gallon (3.8 liters) of clean water into hopper . 2 Close gun air valv e (23). 3 Star t engine, page 15.
Setup 309915D 11 W etting System CA UTION CAUTION 1 Fill hopper (G) with prepared texture material. Do not mix mater ial in hop per . Mixing mater ial in hop per can damage ho pper , result in an inconsist ent mix and pac kout can occur. 2 Install tip .
Setup 12 309915D Mixing Material CA UTION Do not use any solvent-based materials. Use water-based materials only . Proper material mixture is essential. The pump will not operate if material is too thick. NO TE: For best re sults, mix materi al in a separate co ntainer and pour it i nto hopper.
Setup 309915D 13 Fueling Fuel Specifications Refueling Proc edure CA U TION • Use automotiv e gasoline with a pump octane number of 86 or higher. If engine knocks or pi ngs, use a higher octa ne fuel. • U nleaded fuel minimizes com- bustion chamber deposi ts.
Setup 14 309915D • Alwa ys hav e material outlet plug installed in opening (K or L) that you are not using when there is materi al in hopper . If plug is remov ed, hopper will drain out. •a l s o Alwa ys hav e material hose installed in the opening (K or L) when there is material in hop- per .
Startup 309915D 15 Star tup Starting Gas Engine 1 Mov e fuel valv e (B) to open 2 Mov e choke (C) to closed 3 Set throttle (D) to fast 4 Set engine (E) switch ON 5 Flip up pressure unloader valv e (W) to ST ART position. 6 Pull star ter cord (R) . 7 After motor star ts, mov e choke (C) to open and pressure unloader (W) down, to R UN position.
Spray Technique s 16 309915D Spra y T echniques Nozzle Selection 1 Control air volume with gun air f low valv e (31). 2 F or more material v olume, try a larger-orifice tip . IMPORT ANT K eep pump and hose clea n when s witching between simulated acoustic , knockd own and or ange peel applications .
Spray Techniqu es 309915D 17 System Adjustment 1 Open air valv e (A). 2 T est spray pattern on card- board. Hold gun 18 to 30 in. (457 to 762 mm) from surface . Use this spra y distance for most applications. Overlap each stroke 50% in a circular motion.
Spray Technique s 18 309915D Material Flo w Adjustment Air Flow Adjustment Preventing Material Surge at Gun T rigger For Continuous Spraying • For a ligh ter spray patte rn, decrease material pressure at spra y er . • For a hea vier spra y pattern, increase material pressure at spra y er .
Shutdown and Cl eanup 309915D 19 Shutdo wn and Cleanup CA UTION English • T ur n off spray er if you are go ing to stop spra ying for 5 minutes or lo nger .
Maintenan ce 20 309915D Maintenance Component T ask F requency Engine Check Oil Daily Hoses Check f or wear and/or damage Daily Drain system of all water After each use Air and Material Hose Connectio.
Technical Da ta 309915D 21 T echnical Data *Measured while spraying at 1 m. #Measured per ISO-3744 Maximum wor king air pressure 120 psi (8.2 7 bar) Maximum wo rking fluid pressure 120 psi (8.27 bar) Air pressure oper ating range 25 to 120 psi (1.7 to 8.
Warranty 22 309915D Wa r r a n t y Graco warrants all equipment ref erenced in th is document which is manuf actured by Graco and bearing its name to be free from de fe c t s i n material and workmanship on the date of sale to the origin al purch aser for use.
デバイスGraco Inc. 248083の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Graco Inc. 248083をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco Inc. 248083の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco Inc. 248083の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco Inc. 248083で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco Inc. 248083を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco Inc. 248083の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco Inc. 248083に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco Inc. 248083デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
