Graco Inc.メーカー313384Bの使用説明書/サービス説明書
ページ先へ移動 of 18
313384B Operation GTX ™ 2000 EX - For W ater- Based Materials Only - Model 257030 Spra ye r with Graco T rigger Gun 120 psi (8.27 bar) Maxim um Working Air Pressure 120 psi (8.27 bar) Maximum W orking Fluid Pressure Related Manuals : Important Safety Instru ctions Read all warnings and instr u ctions in this manual.
2 313384B Wa r n i n g s The f ollowing wa r nings are for t he setup, use , grounding, mainten ance, and repair of this equipment . The exclama- tion point symbol alerts you to a gener al warning and the hazard symbol ref ers to procedu re-specific risk.
313384B 3 PLASTIC P ARTS CLEANING SOL VENT HAZARD Use only compatib le water-based solv ents to clean plastic structural o r pressure-containing par ts. Man y solve nts can degrade plastic part s and cause them to f ail, which could cause serious injur y or proper ty damage.
Component Identification 4 313384B Component Identification ti13066a A B H D C J G E F K L.
Component Identification List 313384B 5 Component Identification List * Ref erence numbers used in gun illustrations reflect n umbers shown in gun manual 308878.
Pressure Relief Procedure 6 313384B Pressure Relief Pr ocedure 1. T ur n OFF air inlet valv e (E). 2. Open gun air valv e (23). 3. T rigger gun. Spra y material bac k into hopper (G).
Setup 313384B 7 Setup Preparation 1. Connect air a nd material hoses to gun. Tighten securely . 2. Connect one end of material hose (cc) to material outlet (K or L ) and other end to gun material inlet (bb).
Setup 8 313384B Installing Hopper (G) 1. P osition coupler (H) o ver material outlet and slide hopper (G) straight down, o v er fitting as f ar as it will go . Mak e sure hopper brac ket is position ed ov er car t handle rod. 2. Secure latches o n each side by pushing them firmly up into locked position.
Wetting Hose 313384B 9 W etting Hose W et inside of hose bef ore each use to flush out sedi- ment and pre vent te xture material from packing out hose. 1. P our one (1) gallon (3.8 liters) of clean water into hopper . 2. Close gun air v alve (2 3). 3.
Wetting System 10 313384B W etting System 1. Fill hopper (G) with prep ared te xtured material. 2. Install tip (see Nozzle Selection Char t, page 13). 3. Open gun air valv e (23 ) to reliev e air pressure. 4. Inspect hose f or kinks which could restrict fluid flow .
Mixing Material 313384B 11 Mixing Material 1. Slo wly add one bag of te xture to clean wate r as instructed on bag. F or best results , do not use par- tial bags . 2. Agitate to a smooth, lum p-free consis tency . 3. After te xture is thoroughly mix ed, gently set ball end of Material Thickne ss gauge on surface of mixtur e.
Operation Characteristics 12 313384B Operation Characteristics • Alwa y s hav e material outlet plug installed in opening (K or L) not in use when ma terial is in ho pper . If plug is remov ed, hopper will drain out. • Alwa y s ha ve material hose installed in opening (K or L) when material is in hopper .
Spray Techniques 313384B 13 Spra y T echniques Nozzle Selection † Control air v olume with gun air flow v alv e (31). ‡ F or more mater ial v olume, use tip with larger orifice. NO TICE K eep pump and hose clean when switching between simulate d acoustic, knoc kdown, and orange pe el applications.
System Adjustment 14 313384B System Adjustment 1. Open gun air valv e (23). 2. T est spra y patter n on cardboard. Hold gu n 18 to 30 in. (45 to 75 cm) from surf ace. Use this spra y dis- tance for most applicat ions. Overlap each str oke 50% in a circular moti on.
System Adjustment 313384B 15 Material Flow Adjustment • For a lighter spra y pa tter n, dec rease mate rial pres- sure at spra yer . • F or a heavier spr ay pa tter n, increase material pres- sure at spra yer . Air Flow Adjustment • T r igger g un.
Shutdown and Cleanup 16 313384B Shutdo wn and Cleanup After Spra ying 1. Relie ve Pressure , page 6. 2. Fill material hopper with 2 - 4 gallons of clean water . 3. Spra y inside material hopper to circ ulate water through gun and hose . While circulating w ater , use gun to clean material hopper .
Maintenance 313384B 17 Maintenance Te c h n i c a l D a t a Component T ask Frequenc y Hoses Check f or wear and/or damage Daily Drain system of all water After each use Air and Material Hose Connecti.
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. This manual contains English. MM 313384 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC.
デバイスGraco Inc. 313384Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Graco Inc. 313384Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco Inc. 313384Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco Inc. 313384Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco Inc. 313384Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco Inc. 313384Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco Inc. 313384Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco Inc. 313384Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco Inc. 313384Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
