Graco Inc.メーカー795の使用説明書/サービス説明書
ページ先へ移動 of 20
3A0156A Operation Electric Airless Spra yer s - For P ortable Airless Spraying of Ar chitectural Coatings and P aints - 3300 psi (227 bar , 22.7 MP a) Maximum W orking Pressure IMPORT ANT SAFETY INSTRUCTIONS Read all w ar nings and instr uctions in this manual.
Models: 2 3A0156A Models: 695 UL TRA MAX lIl Model QuikReel Hi-Bo y Lo-Bo y 258719 ✓✓ 258720 ✓ 258722 ✓ 258872 ✓ 258873 ✓ 258874 ✓ 258876 ✓ 258877 ✓✓ 826124 ✓✓ 826125 ✓ 82612.
Warnings 3A0156A 3 W arnings The f ollowing warnings are f or the setup , use, g rounding, maintenance and repair of this equipment. The e xclamation point symbol aler ts y ou to a general wa r ning and the hazard symbol ref ers to procedure-specific risks.
Warnings 4 3A0156A FIRE AND EXPLOSION HAZARD Flammable fumes , such as solvent and p aint fumes, in work area can ignite or e xplode. T o help pre vent fire and e xplosion: • Do not spra y flammabl e or combustible materials near an open flame or sources of ignition such as cig- arettes, motors , and electrical equipment.
Warnings 3A0156A 5 W ARNING EQUIPMENT MISU SE HAZARD Misuse can cause death or serious injur y . • Alwa ys wear appropriate glov es, eye protection, and a respir ator or mask when painting. • Do not operate or spra y near children. K eep children aw a y from equipment at all times.
Component Identification 6 3A0156A Component Identification 11. 12. 10. 13. 1. 2. 4. 5. 6. 7. 8. 9. 3. ti14839a 1 Premium Digital Display 2 ON/OFF Switch 3 W atchDog ™ Switch (not av ailable on Mar .
Grounding 3A0156A 7 Gr ounding The spra yer must be g rounded. Grounding reduces the risk of static and electric shoc k by pro viding an escape wire f or the electrical current due to static bu ild up or in the e v ent of a shor t circuit. The spra yer cord includes a gro unding wire with an appropriate gro unding contact.
15/20 Amp Switch (Not Available on All Units) 8 3A0156A 15/20 Amp Switch (Not A vailable on All Unit s) Select 15A or 20A setting based on your circuit rating. Pressure Relief Pr ocedure 1. T ur n power OFF . Wait 7 seconds f or power to dissipate. 2.
Setup 3A0156A 9 Setup 1. Standard Units Only : Connect Graco airless hose to spra yer . Tighten secure ly . 2. Standard Units Only : Connect other end of hose to gun and tighten securely . 3. Engage gun t rigger s af ety . 4. Remo ve t ip guard. 5. Check inlet strainer f or clogs and de bris.
Startup 10 3A0156A Star tup 1. T ur n pressure control to lowest pressure. 2. T ur n power ON . 3. Increase pressur e 1/2 tur n to star t motor and allo w fluid to circulat e through drain tu be for 15 seconds; turn pressure do wn. 4. T urn pr ime v alve forw ard to SPRA Y position.
Switch Tip Installation 3A0156A 11 Switch Tip Installation 1. Use spray tip (A) to inser t OneSe al ™ (B) into guard (C). 2. Inser t Switch Tip . 3. Scre w assemb ly onto gun. Tighten. Spra y 1. Spra y test patter n. Increa se pressure to eliminate heavy ed ges.
WatchDog ™ Protection System (Not Available on All Uni ts) 12 3A0156A W atchDog ™ Pr otection System (Not A vailab le on All Units) Pump stops automatically when m aterial pa il is empty . To A c t i v a t e : 1. P er f or m Startup . 2. Premium units with digi tal display: T ur n W atchDog swit ch ON and WD ON displa ys.
Hose Reel (Not Available on All Units) 3A0156A 13 Hose Reel (Not A vailab le on All Units) 1. Mak e sure hose is routed throug h hose guide. 2. Lift and tur n piv ot lock 90° to unlock hose reel. Pull on hose to remo ve it from hose reel. 3. Pull reel hand le up and tur n cloc kwise to reel in hose .
Digital Tracking System (Not Available on All Uni ts) 14 3A0156A Digital T rac king System (Not A vailab le on All Units) Operation Main Menu Shor t press to mo ve to next d isplay . Press and hold (5 seconds) to chang e units or reset data. 1. T ur n pressu re to lowest setting.
Digital Tracking System (Not Available on All Units) 3A0156A 15 Secondary Menu - Stored Data and W atchDog Pump Protection Modes 1. P er f or m Pressure Relief, steps 1 - 4 if they hav e not already been do ne. 2. T ur n pow er switch on while holding DTS button down.
Cleanup 16 3A0156A Cleanup 1. P er f or m Pressure Relief Procedure (page 8), steps 1 - 4. Remo ve siphon tube set from paint and place in flushing flui d. Remov e tip guard from gun. NO TE : U se wa ter for wat er- bas e paint, mineral spir its f or oil-base paint, or othe r solvents reco mmended by manuf acturer .
Cleanup 3A0156A 17 9. Remov e filters from gun an d spra yer , if installed. Clean and inspect. Install filters. 10. If flushing with water , flush again with mineral spirits, or Pump Ar mor , to leav e a protective coating to pre- vent freezing or corrosion.
Technica l Data 18 3A0156A Te c h n i c a l D a t a Basic Sprayer Wetted Parts......... ..................... zinc- and nick el-plated carbon steel, nylon, stainl ess steel, PTFE, Acetel, leather , UHMWPE, aluminum tungsten carbide, PEEK, brass Noise Level Sound powe r .
Notes 3A0156A 19 Notes.
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. This manual contains English. MM 3A0156 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC.
デバイスGraco Inc. 795の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Graco Inc. 795をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco Inc. 795の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco Inc. 795の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco Inc. 795で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco Inc. 795を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco Inc. 795の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco Inc. 795に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco Inc. 795デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
