Graco Inc.メーカーGC-1402の使用説明書/サービス説明書
ページ先へ移動 of 20
Operation Formula-X Chop GC-1402F ENG Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. Low emission external-mix dispense gun for use with polyester resin and gel coat. For professional use only .
2 GC-1402E Contents W arnings .......................................................... 3 Important Safety Information ......................... 5 Grounding .............................................. .......... 6 Set-Up ..........................
3 GC-1402E W arnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure- specic risk. Refer back to these warnings.
4 GC-1402E W ARNING SKIN INJECTION HAZARD High-pressure uid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. • Do not point gun at anyone or at any part of the body .
5 GC-1402E Important Safety Information Methyl Ethyl Ketone Peroxide (MEKP) MEKP is among the more hazardous materials found in commercial channels. Proper handling of the “unstable (reactive)” chemicals presents a denite challenge to the plastics industry .
6 GC-1402E This equipment needs to be grounded. Ground the dispense gun through connection to a GlasCraft approved grounded uid supply hose. Check your local electrical code and related manuals for detailed grounding instructions of all equipment in the work area.
7 GC-1402E Hose Attachment 1. Push in and rotate the trigger lock to stop the trigger from being activated. 2. Attach the (black p/n 21694-25) material hose to the material inlet tting on the back of the gun. 3. Attach the (red) atomize air tubing to the atomize air inlet tting on the back of the gun.
8 GC-1402E Repair Kits Part Number Description 23792-00 GUN AIR KIT 23793-00 GUN SEAL KIT 23732-00 GUN FLUID V AL VE KIT Standard Equipment Part Number Description 23750-03 FORMULA X CHOP DISPENSE GUN.
9 GC -1402E REVISION C 23750-03 Formula X Chop Dispense Gun Assembly Drawings.
10 GC-1402E REVISION C 23750-03 Formula X Chop Dispense Gun Assembly Drawings 189018.
11 GC-1402E REVISION C Part Number Description Qty . 10773-28C SCREW 1 13867-05 O-RING 1 13867-07 O-RING 3 15845-01 5/32in. BALL DRIVER 1 18383-02 1/4in.
12 GC-1402E T o relieve uid and air pressures: 1. Push down Y ellow slide valve, P/N 21402-00 to bleed off air to system. 2. Open P/N 21228-00 on catalyst pump to recirculation position. 3. Open P/N 21 192-00 on bottom of material pump. 4. V erify the trigger lock is engaged.
13 GC-1402E Parts Replacement Procedure Formula X Chop Gun Before performing maintenance on the dispense gun, follow Pressure Relief Procedure. Due to the different o-ring materials and lubricants used in the dispense guns, never submerge or soak any dis - pense gun in any type of solvent.
14 GC-1402E 4. Place PTFE washers, p/n: 23721-04 on top and bottom of uid valve, p/n: 23743-00. 1. Ensure bores are clean before building material valves. 2. Insert bearing, p/n: 23768-01 into gun body . 3. Insert seal, p/n: 23763-00 into gun body .
15 GC-1402E Dispense T ip Reference Chart Part Number Orice 23047-J1 .012 J2 .014 J3 .022 M1 .012 M2 .014 M3 .022 N1 .012 N2 .014 N3 .022 P1 .012 P2 .014 P3 .022 Note: Use p/n: LP A2-120G and p/n: LP A2-121G when using LP A2-147-XXXX and 23047-XX series spray tips.
16 GC-1402E Dispense T ip Reference Chart Part Number Orice LP A2-147-1525 0.015 1540 0.015 1550 0.015 1565 0.015 1825 0.018 1840 0.018 1850 0.018 1865 0.018 2125 0.021 2140 0.021 2150 0.021 2165 0.021 2325 0.023 2340 0.023 2350 0.023 2365 0.023 2625 0.
17 GC-1402E Part Number Orice Min. Width (in.) Max. Width (in.) Min. Output (lbs.) Max Output (lbs.) 23005- C4 0.040 7 16.5 5.4 10.02 C5 0.050 8.5 15.5 6.36 12.23 C6 0.060 7 17 7.31 1 1.01 C7 0.070 7 13 8.53 10.58 C8 0.080 10 12.5 10.28 13.03 C9 0.
18 GC-1402E T echnical Data Category Data Maximum Fluid Working Pressure 2000 psi (14 MPa, 138 bar) Maximum Air Inlet Pressure 100 psi (0.7 MPa, 7 bar) T ypical Flow Rate of Pattern Guns Dependent of spray tip Maximum Fluid temperature 100° F (38° C) T rigger Air 1/4in.
19 GC -1402E Notes.
Graco Ohio Standard W arranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use.
デバイスGraco Inc. GC-1402の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Graco Inc. GC-1402をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco Inc. GC-1402の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco Inc. GC-1402の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco Inc. GC-1402で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco Inc. GC-1402を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco Inc. GC-1402の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco Inc. GC-1402に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco Inc. GC-1402デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
