Graco Inc.メーカーRTX 1250の使用説明書/サービス説明書
ページ先へ移動 of 18
311768B Operation Interior T e xture Spra y er s R TX 900 & R TX 1250 For W ater-Based Materi als Only Models: 254974 & 254975 70 psi (0.49 MP a, 4.9 bar) Maximum Fluid Working Pressure Related Manuals Import ant Safety Instructions. Read all warnings and instr uctions in this manual.
Warnings 2 Wa r n i n g s The f ollowing are general w arnings related to the setup , use, g rounding, mainten ance and repair of th is equipment. Additional, mo re specific warnings ma y be f ound through out the body of this manual where applicab le.
Warnings 3 Burn Hazard Equipment surf aces and fluid that’ s heate d can become v ery hot dur ing opera tion. T o a void se vere b urns, do not touch hot fl uid or equipment.
Warnings 4 CA UTION • W ater or material remaining in unit when temper atures are belo w freezing ca n damage motor and/or delay pump star tup. Do not allow unit to freeze . • Bef ore adding material or starting unit in cold weather , run warm water through pump .
Component Identi fication 5 Component Identification M D F A G C L Model 254975 Sho wn E K U T V B S Y cc R P bb N H J ti8939a W Item Component Item Component A Handle N Burp Guard B T oolbo x P Mater.
Preparation 6 Preparation Pressure Relief Procedure T o reduce risk of injur y , follo w this procedure whene v er y ou see this symbol throug hout this manual, Also , perf or m this procedure whene ver you : • Stop spra ying • Check or repair a ny par t of this system • Install or clean spra y nozzle 1.
Setup 7 Setup T e xture Spra ying (material supplied from unit) 1. Connect air hose and m ater ial hose to spray er a ir and material hose out lets. 2. Open air valv e. 3. Connect ai r hose to gun. 4. Connect material hose to gun. 5. Mak e sure b urp guard is installed, Cautio n , page 3.
Setup 8 9. T urn power switch ON. 10. Close gun air v alv e. 11. P oint gun into waste buck et and pull trig ger to pump water t hrough the system. Cont inue to trigger gun until material hopper is empty . 12. Add pr e-mixed te xture mix to m ater ial hoppe r .
Setup 9 6. T ur n hopper gun/spr a y gun selector s witch to HOP- PER GUN. 7. Open gun air valv e. 8. T urn power switch ON. 9. T o achiev e uniform spray patter n, adjust air valv e and flo w adjustment n ut on gun. If y ou do not achie ve the desired spr a y pattern, change nozzles (see page 11).
Mixing Material 10 Mixing Material Dry Mix - 40 lb (18 kg) ba g 1. Carefully mix te xture material and water according to manuf acturer instructions on bag. 2. Agitate to mix, using a ha lf-inch, variable speed drill with mixing paddle , to a smooth, lump-f ree consis- tency .
Spray Techniques 11 Spra y T echniques Recommended Nozzle Selection Char t 1 Control air volume with gun air v alve. 2 F or more material v o lume try a larger nozzle. Adjusting the System Sufficient fluid ou tput (v olume and pressure) and good atomization is a balance of atomo zing air , material thickne ss/material flow an d nozzle selection.
Shutdown and Cleanup 12 Shutdo wn and Cleanup T e xture Spra ying (8-10 gallon Ma terial Hopper) When you hav e finishe d spra ying: 1. Open gun air valv e. 2. Mak e sure hopp er gun/spr a y gun selection s witch is tur ned to SPRA Y GUN. 3. T urn power switch ON.
Shutdown and Cleanup 13 Removing Ma terial Hopper Fr om Spray er: The material hopper can be rem ov ed for cleaning . T o remov e material hopper : 1. Loosen botto m fitting. 2. Lift mater ial ho pper straight up, off unit. 3. Plug opening on bo ttom of material hopper with y our hand.
Troubleshooting 14 T r oubleshooting Prob lem C ause Solution Spra yer won’t run P ower s witch not on T ur n s witch on. No pow er at wall outle t Chec k outlet by plugging in another appliance . If appliance does not work, try another outlet. Wrong size ge nerator Use a 3500 wa tt or larger gener ator .
Troubleshooting 15 Speed of application slo w or slow er Material too thick Thin material. Nozzle too small Change nozzles to a larger siz e. See Recommended Nozzle Selection Char t, page 11. T oo much air being used. P ar tially close gun air v alve to r educe air flow .
Technica l Data 16 Te c h n i c a l D a t a *Measured while sp ra ying at 1 m. **Measured per ISO- 3744 Main unit pow er requirement s 120 V ac , 60 Hz, 15A, 1 phase Maximum fluid wor king pressure 70 psi, (4.9 bar) Maximum air w orking pressure 50 psi, (3.
Graco Warra nty 17 Graco W arranty Graco warrants all equipment ref erenced in this document which is manufactured b y Graco and bearing its na me to be free from defects in material and workmanship on the date of sale to the or iginal pu rchaser for use .
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. This manual contains English. MM 311768 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC.
デバイスGraco Inc. RTX 1250の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Graco Inc. RTX 1250をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco Inc. RTX 1250の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco Inc. RTX 1250の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco Inc. RTX 1250で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco Inc. RTX 1250を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco Inc. RTX 1250の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco Inc. RTX 1250に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco Inc. RTX 1250デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
