Graco Inc.メーカーti11418aの使用説明書/サービス説明書
ページ先へ移動 of 28
310892F Operation GMAX ™ II 3900/5900/5900HD/5 900 Con ver tible/7900 T exSpra y 5900HD Con ver tible/7900HD Airless Spra yer s - For P or table Airless Spra ying of Architectur al Coatings and P aints - 3300 psi (22.
Manual Conventions 2 310892F Manu al Con ventions Note WARNING W ARN ING: a potenti ally hazardous situatio n which, if not av oided, could re sult in death or serious injur y . W ar nings in the instr uctions usually include a symbol indicating the ha zard.
Warning 310892F 3 Wa r n i n g The f ollowing warnings include general saf e ty inf or mation f or this equipment. Fur ther product specific w ar nings ma y be included in the text where applicable. WA R N I N G FIRE AND EXPLOSION HAZARD Flammab le fumes, such as solv ent and paint fumes, in wo rk are a can ignite or e xplode.
Warning 4 310892F EQUIPMENT MISUSE HAZARD Misuse can ca use death or serious injury . • Do not exceed the maximum workin g pressure or temperature rating of the lo west rated system component. See T echnical Dat a in all equipment manuals . • Use fluids and solv ents that are compatib le with equipment wetted pa r ts.
Component Identi fication 310892F 5 Component Identification 1 Engine controls 2 Engine ON/OFF s witch 3 Premium Digital Display 4 Pump On /Off Switch 5 Pressure control 6 Prime valv e & Filter 7 .
Setup 6 310892F Setup 1. Connect appr opr iate Graco high-p ressure hose to spray er. Tighten secu rely . 2. Install adapter an d 3.6m whip hose to other end of 15m airless hose. 3. Install whip hose to fluid inlet of spra y gun. 4. Tighten securely .
Setup 310892F 7 6. Remov e inlet strainer and filter bowl screen when spraying plaster materi- als. 7. Fill throat packing nut with TSL to pre- v ent premature packing wear . Do this each time you spra y . 8. Check engine oil le vel. Add SAE 10W -30 (summer) or 5W -20 (winter), if necessary .
Setup 8 310892F Con ver tible Mod els Chang e Engine to M otor 1. Disconnect engine power cord. 2. Release tension ba r . 3. Remov e e ngine; tilt and slide back.
Setup 310892F 9 Con ver tible Mod els Change Motor to Engine 1. Look through side vent holes and ensure dr ive belt is in motor pulley . 2. Secur e motor with t en- sion bar .
Startup 10 310892F Star tup 1. Place suction tube and drain tube in grounded metal pail par tially fi lled with flushing fluid. Attach ground wire to pail and to ear th ground. 2. T ur n prime valve do wn. T ur n pressure control counterclockwise to low- est pressure.
Startup 310892F 11 4. Start engine a Mov e fuel valve to open. b Mov e choke to closed. c Set throttle to f ast. d Set engine s witch to ON. ti524 8 a ti5249a ti5250a ti5262a.
Startup 12 310892F 5. Set pump s witch ON. - Pump/clutch is now active - e Pull star ter rope. f After engine star ts, mov e choke to open. g Set throttle to desi red setting.
Startup 310892F 13 6. Increase pressure enough to star t pump stroking and allow fluid to circulate f or 15 seconds; tur n pressure down and turn pr ime v alve horizontal. 7. T ake spr ay gun tr igger saf ety OFF . 8. Hold gun against grounded metal flushing pail.
Startup 14 310892F SwitchTip and Guar d Assembly 9. Place siphon tube in material p ail. 10. T r igger gun again i nto flushing fluid pail until material appears. Assemble tip and guard, page 14. 1. Put trigger safe ty ON. Inser t SwitchTip . Inser t seat and OneSeal ™ .
Startup 310892F 15 Clearing Tip Clogs 1. T ri gger gun and spray test pattern. Slowly adjust pressure to elimi- nate heavy edges. Use smaller tip size if pres- sure adjustment can not eliminate heavy edges. 2. Hold gun per pendicular , 10-12 in. (25-30 cm) from surface .
Startup 16 310892F Premium Operat ion Main Men u Close cov er when spra ying to protect display . 1. Do star tup steps 1. - 3. 2. Star t engine, page 11. Spray er M odel momen- tarily displa ys, e.g., G5900 = GMAX 5900 Pressure displa y appears. Dashes appear when pressure is less than 200 psi (14 ba r , 1.
Startup 310892F 17 Digital T racking System ™ (DTS) 3. Shor t press DTS button to move to Job Gallons (or Liters x 10). Note: JOB displa ys briefly , then the number of gallons spray ed above 800 psi (55 bar , 5.5 MP a). 4. Press and hold to reset to z e ro , or shor t press DTS button to mov e to Life- time Gallons (or Liters x 10).
Startup 18 310892F W atchDog ™ Pr otection System Pump stops automatically when materi al pail is empty . Change Display Units: T o Activate: 1. Do Startup. 2. T ur n W atchDog s witch ON and WD ON dis- pla ys. EMPTY displa ys / flashes and the pump stops when W atchDog protection system detects an empty mate- rial pail.
Startup 310892F 19 Secondary Menu - Stored Data an d W atchDog Pump Protec tion Modes 1. Do Startup steps 1. - 3. Pressure must be at zer o. 2. Star t engine, page 11. Pressure displa y appears. 3. Press and hold DTS but- ton and tur n pump s w itch ON.
Startup 20 310892F Secondary Menu - Stored Data and W atchDog Pump Prot ection Modes 4. Shor t press DTS button and date code disp la ys. 5. Shor t press DTS button and par t number dis- pla ys. 6. Shor t press DTS button and engine hours dis- plays .
Startup 310892F 21 Secondary Menu - Stored Data an d W atchDog Pump Protec tion Modes 8. Press and hold DTS but- ton until CLEAR ERROR NO ERROR CODE scrolls through the dis- play and then error code E=00 displa ys. See Manual 310893. 9. Shor t press DTS button again to mov e to W atch- Dog mode.
Startup 22 310892F Secondary Menu - Stored Data and W atchDog Pump Prot ection Modes 12. Shor t press DTS button and software re visi on displa ys. 13.
Cleanup 310892F 23 Cleanup If yo u suspect spra y tip or hose is clogged o r that pres- sure has not been fully r e lie ved after f o llowing the steps abov e, VER Y SLOWL Y lo osen tip guard retaining nut or hose end coupling to re liev e pressure gradually , then loosen completely .
Cleanup 24 310892F 5. Unscrew bo wl, remove filter . Assemble without filter . Clean fliter . 6. Clean filter , guard and SwitchTip in fl ushing fluid. 7. Remov e siph on tube set from materi al and place in flushing fluid. Use water f or water base mater ial and appropri ate solvent f or oil base mater ial.
Cleanup 310892F 25 9. Hold gun against mate - rial pail. T a k e trigger saf ety OFF . T ur n pres- sure control up until motor begins to dr ive pump . T rigger gun until flushing fluid appears. 10. Mo ve gun to fl ushing pail, hold gun against pail, trigge r gun to thor- oughly flush system.
Cleanup 26 310892F Caution: If flushing with w ater, do not leav e water in spra yer . Flush again with min eral spirits, oil or Pump Ar mor and leav e this protec- tive coating in the spr ayer to help prev ent freezing or corrosion and increase spray er li f e.
Warranty / Garantie / Garantía / Garanzia / Garantia 310892F 27 W arranty / Garantie / Garantía / Garanzia / Garantia Graco warrants all equipment referenced in this document which is manuf actured by Graco and bearing its name to be free from de fec t s in material and workmanship on the date of sale to the original pu rc haser for use .
Warranty / Garantie / Garantía / Garanzia / Garantia 28 310892F T O PLACE AN ORDER , contact y our Graco distributor , or call 1-800-69 0-2894 to identify the nearest distr ibu tor . All written and visual data contained in this document reflects the latest product information available at the time of publica tion.
デバイスGraco Inc. ti11418aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Graco Inc. ti11418aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco Inc. ti11418aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco Inc. ti11418aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco Inc. ti11418aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco Inc. ti11418aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco Inc. ti11418aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco Inc. ti11418aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco Inc. ti11418aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
