GrizzlyメーカーG1007の使用説明書/サービス説明書
ページ先へ移動 of 23
HEAVY-DUTY MILL/DRILL MODEL G1006/G1007 INSTRUCTION MANUAL COPYRIGHT © 1999 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. OCTOBER, 1999 PRINTED IN U.
G1006/G1007 Mill/Drill -2- Table Of Contents PAGE 1. SAFETY SAFETY INSTRUCTIONS FOR POWER TOOLS ............................................................3-4 ADDITIONAL SAFETY INSTRUCTIONS FOR MILL/DRILLS ............................................
-3- Safety Instructions For Power Tools SECTION 1: SAFETY 5. KEEP CHILDREN AND VISITORS AWAY . All children and visitors should be kept a safe distance from work area. 6. MAKE WORK SHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.
-4- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
-5- G1006/G1007 Mill/Drill Additional Safety Instructions Mill / Drills 1. DO NOT use until unit is completely assem- bled and installed according to instructions. 2. DO NOT use the Mill/Drill until all controls and adjustments are understood. 3. BE SURE drill bit or cutter is securely locked in the chuck or holder.
G1006/G1007 Mill/Drill -6- 110V Operation SECTION 2: CIRCUIT REQUIREMENTS The Model G1006/G1007 can be fused at 20 amps. If the circuit breakers trip frequently, and you have determined you are on a dedicated cir- cuit with no other loads, it may be necessary to upgrade to a 25 amp circuit.
We do not recommend the use of extension cords on 220V equipment. It is much better to arrange the placement of your equipment and the installed wiring to eliminate the need for extension cords. Should it be necessary to use an extension make sure the cord is rated Hard Service (grade S) or better.
-8- SECTION 3: INTRODUCTION We are proud to offer the Grizzly Models G1006/G1007 Milling/Drilling Machine. These machines are part of a growing Grizzly family of fine metalworking machinery.
-9- G1006/G1007 Mill/Drill Unpacking This Milling/Drilling Machine is shipped from the manufacturer in a carefully packed crate. If you discover the machine is damaged after you’ve signed for delivery, and the truck and driver are gone, you will need to file a freight claim with the carrier.
-10- Clean Up The unpainted surfaces are coated with a waxy oil to protect it from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser. Avoid chlo- rine-based solvents as they may damage painted surfaces they may contact.
-11- Do not use the angle vise for milling. It is made strictly for holding materials to be drilled. This vise will not adequately clamp an object safely for a milling oper- ation. There is not enough clamping pres- sure available and objects may be pulled out or upset in the vise jaws causing cut- ting tools to break and/or parts to be thrown.
-12- G1006/G1007 Mill/Drill Power feed The Model G1007 features a 110V auto-feed mechanism which allows hands-free, side-to-side passes while milling. Variable-speed feed control makes flat surface milling more consistent. To install the power feed: 1.
-13- G1006/G1007 Mill/Drill Handwheels/Crank There are three handwheels provided with the machine which control table movement. They are secured with setscrews and mounted as follows. Height adjustment is made using the crank pro- vided. Each handwheel has a setscrew which tightens with a 3mm Allen ® wrench.
-14- G1006/G1007 Mill/Drill Drill Chuck/Arbor Your Mill/Drill has been pre-fitted with a drill chuck arbor that has an R-8 shank and a Jacob’s Taper. It is ready to accept the standard drill chuck provided with this machine. To install the drill chuck: 1.
-15- G1006/G1007 Mill/Drill SECTION 5: ADJUSTMENTS Graduated Dials The graduated dials on the handwheels for the table and fine feed can be indexed or “zeroed” to help make accurate and convenient movements. Each dial can be reset or locked with the set- screw or thumbscrew provided.
-16- G1006/G1007 Mill/Drill The G1006/G1007 is capable of twelve different speed settings. Different types of cuts and types of materials require varying speeds. Consult out- side sources for information about appropriate speeds for different applications.
-17- G1006/G1007 Mill/Drill SECTION 6: OPERATIONS The power feed will move the table in the X-plane only. To operate the power feed: 1. Loosen the table locking levers located just below the front edge of the table. 2. Adjust the table stops to the right and left to the desired distance you wish the table to travel.
-18- Once assembly is complete and adjustments are done to your satisfaction, you are ready to test run the machine. Turn on the power supply at the main panel. Press the START button. Make sure that your fin- ger is poised on the STOP button, just in case there’s a problem.
-19- SECTION 7: MAINTENANCE Your Model G1006/G1007 Mill/Drill requires very little maintenance. A thorough cleaning, now and again, will increase the machine’s durability and efficiency by removing chips and grime that can gum up moving parts. It is best of course, to do this after each use.
-20- V-Belts Inspect regularly for tension and wear. Replace when necessary with a size B-42 belt for the spin- dle pulley to the idler pulley belt and a size B-34 belt from the idler pulley to the motor pulley belt. Check pulleys to ensure that they are properly aligned.
-21- The spring tension for automatic quill recoil has been pre-set at the factory. It should not need adjustment under most normal circum- stances. If it does need adjustment, the spring housing is located on the left side of the head. To adjust the spring tension: 1.
-22- The following pages contain general machine data, parts diagrams/lists and Warranty/Return information for your Model G1006/G1007 Milling/Drilling Machine. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department.
-23- G1006/G1007 Mill/Drill Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
デバイスGrizzly G1007の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Grizzly G1007をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly G1007の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly G1007の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly G1007で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly G1007を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly G1007の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly G1007に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly G1007デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。