GrizzlyメーカーG1067Zの使用説明書/サービス説明書
ページ先へ移動 of 28
WOOD LATHE MODEL G1067Z INSTRUCTION MANUAL COPYRIGHT © 1996 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED FEBRUARY, 1999. PRINTED IN U.
G1067Z Wood Lathe -1- Table Of Contents PAGE 1. INTRODUCTION ........................................................................................................2 SAFETY RULES FOR ALL TOOLS .........................................................
-2- G1067Z Wood Lathe Grizzly Industrial, Inc. is proud to offer the Model G1067Z Wood Lathe. This lathe is a part of Grizzly’s growing family of fine woodworking machinery. When used according to the guide- lines stated in this manual, you can expect years of trouble-free, enjoyable operation.
G1067Z Wood Lathe -3- 12. USE SAFETY GLASSES AND EAR PRO- TECTION. Also use a DUST MASK if the operation is dusty. 13. DO NOT OVERREACH. Keep proper foot- ing and balance at all times. 14. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance.
-4- G1067Z Wood Lathe Unpacking The Model G1067Z Wood Lathe is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice. Save the containers and all packing materials for possible inspection by the carrier or its agent.
G1067Z Wood Lathe -5- Clean up Site Considerations Working Clearances: Consider existing and anticipated needs, size of material to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a home for your Wood Lathe.
-6- G1067Z Wood Lathe Circuit Requirements Be sure that your particular electrical con- figuration complies with local and state codes. The best way to ensure compliance is to check with your local municipality or licensed electrician. The motor supplied with the G1067Z is wired for 110V only.
G1067Z Wood Lathe -7- Pre-assembly Assembly of the G1067Z is straightforward. We have organized the assembly process into steps. Please follow them in sequence.
-8- G1067Z Wood Lathe Figure 2. Figure 3. Figure 4. 4. With an assistant, set the lathe bed assem- bly on the stand, orienting the front of the headstock with the switch opening in the stand leg. Bolt the lathe bed to the stand using the eight 5 ⁄ 16 '' - 18 x 1 1 ⁄ 4 '' Cap Screws and Hex Nuts supplied and tighten down.
G1067Z Wood Lathe -9- Installing the Switch Figure 5. Figure 6. 1. Locate the on/off switch and the front and rear covers which will be held in place by two Phillips ® head screws. 2. Make sure the wiring from the switch goes through the rear cover box.
-10- G1067Z Wood Lathe Tool Rest Figure 7. The tool rest is equipped with a cam-action clamping system to secure it to the lathe bed. When the lever is thrown, a locking plate lifts up and secures the tool rest to the bed. To install the tool rest assembly: 1.
G1067Z Wood Lathe -11- Spur Center Figure 9. Figure 10. The G1067Z is supplied with a #2 Morse taper spur center for use when spindle turning. The spur center is used in conjunction with the tail- stock live center. Install the spur center by insert- ing into the hole in the inboard spindle.
-12- G1067Z Wood Lathe SECTION 3: ADJUSTMENTS The Model G1067Z headstock can be swiveled 180˚ as well as positioned anywhere along the bed. To position the headstock along the bed: 1. Loosen the quick release lever by pushing it down. Figure 12. 2. Move the headstock to the desired position and re-engage the quick release lever.
G1067Z Wood Lathe -13- 3. Release the set pin. Make sure the set pin has engaged in its detent by trying to rotate the headstock. 4. Now position the head stock along the bed as desired and engage the quick release lever. The tailstock is equipped with a cam-action clamping system to secure it to the lathe bed.
(1) The tailstock barrel lock handle must always be locked down while the lathe is in use. Figure 18. The workpiece can be thrown from the lathe if this step is not observed. (2) The tailstock barrel should not protrude from the tailstock housing more than 2''.
G1067Z Wood Lathe -15- SECTION 4: OPERATIONS Safety Rules For Wood Lathes Always wear ANSI-approved safety glasses or goggles and hearing protection when operating equipment — particularly when testing new tools or machinery. Do not allow visitors into your workshop when testing or operating equipment.
-16- G1067Z Wood Lathe Adjust the tool rest as close to the workpiece as possible without actually coming in contact with the workpiece. Test by hand turning the work- piece before turning lathe on. Ensure that the lathe chisel is fully supported by the tool rest.
G1067Z Wood Lathe -17- Spindle turning is described as turning work between the two centers. Turning a spindle can be a very simple or a highly intricate operation. To mount a workpiece between centers: 1. Locate the center point on both ends of the workpiece by carefully drawing diagonal lines from corner to corner.
-18- G1067Z Wood Lathe Outboard turning is usually done when stock diameter is greater than 12''. For the size of this particular lathe and its minimum turning speed, we recommend a maximum diameter of 17'' and a maximum thickness of 2''.
G1067Z Wood Lathe -19- SECTION 5: MAINTENANCE Lubrication Bed The G1067Z Lathe is equipped with a split pulley system which allows the speed of the lathe to be changed while its running. To assure the smooth operation of this pulley system, we recommend the main spindle and motor spindle be greased occasionally.
-20- G1067Z Wood Lathe SECTION 6: CLOSURE The following pages contain general machine data, parts diagram, parts list and Warranty/Return information for your Model G1067Z Lathe. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call the appropriate region- al Service Department.
G1067Z Wood Lathe -21- Design Type ......................................................................................................Floor Model Overall Dimensions: Including Stand ..................................................................
19 1 34 35 34 35 34 35 24 67 74 70 71 72 87 10 86 3 20 8 9 68 74 21 75 80 38 39 12 17 82 84 6 14 13 15 16 2 41 54 85 4 50 52 53 18 55 83 33 27 28 30 79 29 43 26 55 5 7 3 23 37 25 55 32 36 22 98 64 11 .
44 45 77 56 57 66 31 46 49 58 59 60 51 47 59 58 60 62 59 58 65 61 63 48 -23-.
-24- G1067Z Wood Lathe 1 P1067Z001 BED 2 P1067Z002 HEADSTOCK 3 P6205 BEARING 6205-2RS 4 P1067Z004 INDEXING BLOCK 5 P1067Z005 MAIN SPINDLE 6 PFH08 FLAT HD SCR 10-24 X 1 ⁄ 2 '' 7 P1067Z007 K.
10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10".
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_____________________________.
G1067Z Wood Lathe -27- Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
デバイスGrizzly G1067Zの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Grizzly G1067Zをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly G1067Zの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly G1067Zの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly G1067Zで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly G1067Zを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly G1067Zの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly G1067Zに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly G1067Zデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
